ASTM C478-02

Standard Specification for Precast Reinforced Concrete Manhole Sections

SCOPE
1.1 This specification covers the manufacture and purchase requirements of products used for the assembly and construction of precast reinforced concrete manholes used in sewer and water works.
1.2 Part I, Sections 1-11, of this specification presents general requirements and requirements that are common to each precast concrete product covered by this specification.
1.3 Part II of this specification presents specific requirements for each manhole product in the following sections: ProductSectionGrade Rings12Flat Slab Tops13Risers and Conical Tops14Base Sections15Steps and Ladders16
Note 1—Future products will to be included in Part II in a future revision of this specification.
1.4 A complete metric companion to this specification has been developed, Specification C 478M; therefore, no metric equivalents are presented in this specification.
Note 2—This specification is a manufacturing and purchase specification only and does not include requirements for backfill, or the relationship between field load conditions and the strength requirements of the manhole products and appurtenances. Experience has shown, however, that the successful performance of this product depends upon the proper selection of the product strength, type of foundation and backfill, and care in the field installation of the manhole products and connecting pipes. The owner of the project for which these products are specified herein is cautioned to require inspection at the construction site.

General Information

• Status: Historical
• Publication Date: 09-Apr-2002
• ICS: 13.060.30 - Sewage water
• Technical Committee: C13 - Concrete Pipe
• Drafting Committee: C13.06 - Manholes and Specials

Relations

• Replaces: ASTM C478-97 - Standard Specification for Precast Reinforced Concrete Manhole Sections
• Effective Date: 10-Apr-2002
• Replaced By: ASTM C478-02ae1 - Standard Specification for Precast Reinforced Concrete Manhole Sections
• Effective Date: 10-Sep-2002
• Referred By: ASTM C990-09(2019) - Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
• Effective Date: 10-Apr-2002
• Referred By: ASTM C858-19 - Standard Specification for Underground Precast Concrete Utility Structures
• Effective Date: 10-Apr-2002
• Referred By: ASTM C857-19 - Standard Practice for Minimum Structural Design Loading for Underground Precast Concrete Utility Structures
• Effective Date: 10-Apr-2002
• Referred By: ASTM C1889-21 - Standard Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Utility, Water, and Wastewater Structures Using AASHTO LRFD Design
• Effective Date: 10-Apr-2002

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: C 478 – 02
Standard Specification for
1
Precast Reinforced Concrete Manhole Sections
This standard is issued under the fixed designation C 478; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
PART I—GENERAL A 496 Specification for Steel Wire, Deformed, for Concrete
2
Reinforcement
1. Scope
A 497 Specification for Steel Welded Wire Reinforcement,
2
1.1 This specification covers the manufacture and purchase Deformed, for Concrete
requirements of products used for the assembly and construc-
A 615/A 615M Specification for Deformed and Plain
2
tion of precast reinforced concrete manholes used in sewer and Billet-Steel Bars for Concrete Reinforcement
3
water works.
C 33 Specification for Concrete Aggregates
1.2 Part I, Sections 1-11, of this specification presents
C 39 Test Method for Compressive Strength of Cylindrical
3
general requirements and requirements that are common to Concrete Specimens
4
each precast concrete product covered by this specification.
C 150 Specification for Portland Cement
1.3 Part II of this specification presents specific require- C 309 Specification for Liquid Membrane-Forming Com-
3
ments for each manhole product in the following sections:
pounds for Curing Concrete
C 497 Test Methods for Concrete Pipe, Manhole Sections,
Product Section
5
Grade Rings 12
or Tile
Flat Slab Tops 13
4
C 595 Specification for Blended Hydraulic Cements
Risers and Conical Tops 14
Base Sections 15 C 618 Specification for Fly Ash and Raw or Calcined
Steps and Ladders 16
Natural Pozzolan for Use as a Mineral Admixture in
3
NOTE 1—Future products will to be included in Part II in a future Concrete
revision of this specification.
C 822 Terminology Relating to Concrete Pipe and Related
5
Products
1.4 A complete metric companion to this specification has
2.2 ACI Standard:
been developed, Specification C 478M; therefore, no metric
6
318 Building Code, Requirements for Reinforced Concrete
equivalents are presented in this specification.
NOTE 2—This specification is a manufacturing and purchase specifica- 3. Terminology
tion only and does not include requirements for backfill, or the relation-
3.1 Definitions—For definitions of terms relating to precast
ship between field load conditions and the strength requirements of the
reinforced concrete manholes, see Terminology C 822.
manhole products and appurtenances. Experience has shown, however,
that the successful performance of this product depends upon the proper
4. Materials and Manufacture
selection of the product strength, type of foundation and backfill, and care
in the field installation of the manhole products and connecting pipes. The 4.1 General material requirements for precast reinforced
owner of the project for which these products are specified herein is
concrete manhole products are presented in 4.1.1-4.1.5. Other
cautioned to require inspection at the construction site.
materials or additional requirements for a product, if any, are
covered in the Part II section for that specific product.
2. Referenced Documents
4.1.1 Reinforced Concrete—Reinforced concrete shall con-
2.1 ASTM Standards:
sist of cementitious materials, mineral aggregates, and water, in
A 82 Specification for Steel Wire, Plain, for Concrete Re-
which steel reinforcement has been embedded in such a
2
inforcement
manner so that the steel reinforcement and concrete act
A 185 Specification for Steel Welded Wire Reinforcement,
together.
2
Plain, for Concrete
4.1.2 Cementitious Materials:
1
This specification is under the jurisdiction of ASTM Committee C13 on
3
Concrete Pipe and is the direct responsibility of Subcommittee C13.06 on Manholes Annual Book of ASTM Standards, Vol 04.02.
4
and Specials. Annual Book of ASTM Standards, Vol 04.01.
5
Current edition approved April 10, 2002. Published June 2002. Originally Annual Book of ASTM Standards, Vol 04.05.
6
published as C 478 – 61T. Last previous edition C 478 – 97. Available from the American Concrete Institute, Box 4754, Redford Station,
2
Annual Book of ASTM Standards, Vol 01.04. Detroit, MI 48219.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
C 478
4.1.2.1 Cement—Cement shall conform to the requirements requirements are given in the Part II section for a specific
for portla
...