ASTM E561-15a
(Test Method)Standard Test Method for KR Curve Determination
Standard Test Method for <emph type="bdit">K<inf>R</inf></emph> Curve Determination
SIGNIFICANCE AND USE
5.1 The KR curve characterizes the resistance to fracture of materials during slow, stable crack extension and results from the growth of the plastic zone ahead of the crack as it extends from a fatigue precrack or sharp notch. It provides a record of the toughness development as a crack is driven stably under increasing applied stress intensity factor K. For a given material, KR curves are dependent upon specimen thickness, temperature, and strain rate. The amount of valid KR data generated in the test depends on the specimen type, size, method of loading, and, to a lesser extent, testing machine characteristics.
5.2 For an untested geometry, the KR curve can be matched with the crack driving (applied K) curves to estimate the degree of stable crack extension and the conditions necessary to cause unstable crack propagation (2). In making this estimate, KR curves are regarded as being independent of initial crack size ao and the specimen configuration in which they are developed. For a given material, material thickness, and test temperature, KR curves appear to be a function of only the effective crack extension Δae (3).
5.2.1 To predict crack behavior and instability in a component, a family of crack driving curves is generated by calculating K as a function of crack size for the component using a series of force, displacement, or combined loading conditions. The KR curve may be superimposed on the family of crack driving curves as shown in Fig. 1, with the origin of the KR curve coinciding with the assumed initial crack size ao. The intersection of the crack driving curves with the KR curve shows the expected effective stable crack extension for each loading condition. The crack driving curve that develops tangency with the KR curve defines the critical loading condition that will cause the onset of unstable fracture under the loading conditions used to develop the crack driving curves.
5.2.2 Conversely, the KR curve can be shifted left or right in Fig...
SCOPE
1.1 This test method covers the determination of the resistance to fracture of metallic materials under Mode I loading at static rates using either of the following notched and precracked specimens: the middle-cracked tension M(T) specimen or the compact tension C(T) specimen. A KR curve is a continuous record of toughness development (resistance to crack extension) in terms of KR plotted against crack extension in the specimen as a crack is driven under an increasing stress intensity factor, K. (1)2
1.2 Materials that can be tested for KR curve development are not limited by strength, thickness, or toughness, so long as specimens are of sufficient size to remain predominantly elastic to the effective crack extension value of interest.
1.3 Specimens of standard proportions are required, but size is variable, to be adjusted for yield strength and toughness of the materials.
1.4 Only two of the many possible specimen types that could be used to develop KR curves are covered in this method.
1.5 The test is applicable to conditions where a material exhibits slow, stable crack extension under increasing crack driving force, which may exist in relatively tough materials under plane stress crack tip conditions.
1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E561 − 15a
Standard Test Method for
1
K Curve Determination
R
This standard is issued under the fixed designation E561; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
3
2.1 ASTM Standards:
1.1 This test method covers the determination of the
E4Practices for Force Verification of Testing Machines
resistance to fracture of metallic materials under Mode I
E399Test Method for Linear-Elastic Plane-Strain Fracture
loadingatstaticratesusingeitherofthefollowingnotchedand
Toughness K of Metallic Materials
Ic
precrackedspecimens:themiddle-crackedtensionM(T)speci-
E1823TerminologyRelatingtoFatigueandFractureTesting
men or the compact tension C(T) specimen. A K curve is a
R
2.2 Other Document:
continuous record of toughness development (resistance to
4
AISCSteel Construction Manual
crackextension)intermsof K plottedagainstcrackextension
R
in the specimen as a crack is driven under an increasing stress
3. Terminology
2
intensity factor, K. (1)
3.1 Definitions—Terminology E1823 is applicable to this
1.2 Materials that can be tested for K curve development
R
method.
are not limited by strength, thickness, or toughness, so long as
3.2 Definitions of Terms Specific to This Standard:
specimensareofsufficientsizetoremainpredominantlyelastic
3.2.1 apparent plane-stress fracture toughness, K —The
app
to the effective crack extension value of interest.
value of K calculated using the initial crack size and the
maximum force achieved during the test. K is an engineer-
1.3 Specimensofstandardproportionsarerequired,butsize
app
ing estimate of toughness that can be used to calculate residual
is variable, to be adjusted for yield strength and toughness of
strength. K depends on the material, specimen size, and
the materials.
app
specimen thickness and as such is not a material property.
1.4 Only two of the many possible specimen types that
-2
3.2.2 effective modulus, E [FL ]—an elastic modulus that
eff
couldbeusedtodevelop K curvesarecoveredinthismethod.
R
allows a theoretical (modulus normalized) compliance to
1.5 The test is applicable to conditions where a material match an experimentally measured compliance for an actual
exhibits slow, stable crack extension under increasing crack initial crack size a .
o
driving force, which may exist in relatively tough materials
3.2.3 plane-stress fracture toughness, K —The value of K
c R
under plane stress crack tip conditions.
at instability in a force-controlled test corresponding to the
maximum force point in the test. K depends on the material,
c
1.6 The values stated in SI units are to be regarded as the
specimen size, and specimen thickness and as such is not a
standard. The values given in parentheses are for information
material property.
only.
3.2.3.1 Discussion—See the discussion of plane-strain frac-
1.7 This standard does not purport to address all of the
ture toughness in Terminology E1823.
safety concerns, if any, associated with its use. It is the
4. Summary of Test Method
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
4.1 During slow-stable fracturing, the developing crack
bility of regulatory limitations prior to use.
extension resistance K is equal to the applied stress intensity
R
factor K. The crack is driven forward by continuously or
incrementally increasing force or displacement. Measurements
1
This test method is under the jurisdiction ofASTM Committee E08 on Fatigue
and Fracture and is the direct responsibility of Subcommittee E08.07 on Fracture
3
Mechanics. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Dec. 1, 2015. Published December 2015. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1974. Last previous edition approved in 2015 as E561–15. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/E0561-15A. the ASTM website.
2 4
Theboldfacenumbersinparenthesesrefertothelistofreferencesattheendof Available from American Institute of Steel Construction (AISC), One E.
this standard. Wacker Dr., Suite 700, Chicago, IL 60601-1802, http://www.aisc.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E561 − 15a
are made periodically for determination of the effective crack
size and for calculation of K values, which are
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E561 − 15 E561 − 15a
Standard Test Method for
1
K Curve Determination
R
This standard is issued under the fixed designation E561; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This test method covers the determination of the resistance to fracture of metallic materials under Mode I loading at static
rates using either of the following notched and precracked specimens: the middle-cracked tension M(T) specimen or the compact
tension C(T) specimen. A K curve is a continuous record of toughness development (resistance to crack extension) in terms of
R
2
K plotted against crack extension in the specimen as a crack is driven under an increasing stress intensity factor, K.(1)
R
1.2 Materials that can be tested for K curve development are not limited by strength, thickness, or toughness, so long as
R
specimens are of sufficient size to remain predominantly elastic to the effective crack extension value of interest.
1.3 Specimens of standard proportions are required, but size is variable, to be adjusted for yield strength and toughness of the
materials.
1.4 Only two of the many possible specimen types that could be used to develop K curves are covered in this method.
R
1.5 The test is applicable to conditions where a material exhibits slow, stable crack extension under increasing crack driving
force, which may exist in relatively tough materials under plane stress crack tip conditions.
1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
E4 Practices for Force Verification of Testing Machines
E399 Test Method for Linear-Elastic Plane-Strain Fracture Toughness K of Metallic Materials
Ic
E1823 Terminology Relating to Fatigue and Fracture Testing
2.2 Other Document:
4
AISC Steel Construction Manual
3. Terminology
3.1 Definitions—Terminology E1823 is applicable to this method.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 apparent plane-stress fracture toughness, K —The value of K calculated using the originalinitial crack size and the
app
maximum force achieved during the test. K is an engineering estimate of toughness that can be used to calculate residual
app
strength. K depends on the material, specimen size, and specimen thickness and as such is not a material property.
app
-2
3.2.2 effective modulus, E [FL ]—an elastic modulus that allows a theoretical (modulus normalized) compliance to match an
eff
experimentally measured compliance for an actual initial crack size a .
o
1
This test method is under the jurisdiction of ASTM Committee E08 on Fatigue and Fracture and is the direct responsibility of Subcommittee E08.07 on Fracture
Mechanics.
Current edition approved Oct. 15, 2015Dec. 1, 2015. Published December 2015. Originally approved in 1974. Last previous edition approved in 20102015 as
ε2
E561 – 10E561 – 15. . DOI: 10.1520/E0561-15.10.1520/E0561-15A.
2
The boldface numbers in parentheses refer to the list of references at the end of this standard.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American Institute of Steel Construction (AISC), One E. Wacker Dr., Suite 700, Chicago, IL 60601-1802, http://www.aisc.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E561 − 15a
3.2.3 plane-stress fracture toughness, K —The value of K at instability in a force-controlled test corresponding to the
c R
maximum force point in the test. K depends on the material, specimen size, and specimen thickness and as such is not a material
c
property.
3.2.3.1 Discussion—
See the discussion of plane-strain fractu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.