ASTM A479/A479M-01

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels

SCOPE
1.1 This specification  covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction.
Note 1—There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol 02.04.
1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standards; within the text and tables, the SI units are shown in [brackets]. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.3 Unless the order specifies the applicable "M" specification designation, the material shall be furnished to the inch-pound units.

General Information

• Status: Historical
• Publication Date: 09-Mar-2002
• ICS: 77.140.30 - Steels for pressure purposes
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.17 - Flat-Rolled and Wrought Stainless Steel

Relations

• Replaces: ASTM A479/A479M-00 - Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
• Effective Date: 10-Mar-2002
• Replaced By: ASTM A479/A479M-02a - Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
• Effective Date: 10-Dec-2002
• Referred By: ASTM A484/A484M-23 - Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
• Effective Date: 10-Mar-2002
• Referred By: ASTM F1376-92(2020) - Standard Guide for Metallurgical Analysis for Gas Distribution System Components (Withdrawn 2023)
• Effective Date: 10-Mar-2002
• Referred By: ASTM A182/A182M-23 - Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
• Effective Date: 10-Mar-2002
• Referred By: ASTM A1069/A1069M-19 - Standard Specification for Laser and Laser Hybrid Welded Stainless Steel Bars, Plates, and Shapes
• Effective Date: 10-Mar-2002
• Referred By: ASTM A1082/A1082M-16(2021) - Standard Specification for High Strength Precipitation Hardening and Duplex Stainless Steel Bolting for Special Purpose Applications
• Effective Date: 10-Mar-2002
• Referred By: ASTM A580/A580M-23 - Standard Specification for Stainless Steel Wire
• Effective Date: 10-Mar-2002
• Referred By: ASTM F1508-96(2021) - Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services
• Effective Date: 10-Mar-2002
• Referred By: ASTM C1533-15(2022) - Standard Guide for General Design Considerations for Hot Cell Equipment
• Effective Date: 10-Mar-2002
• Referred By: ASTM F3184-16 - Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion
• Effective Date: 10-Mar-2002
• Referred By: ASTM F1387-23 - Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings
• Effective Date: 10-Mar-2002
• Referred By: ASTM B649-21 - Standard Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloy and Cr-Ni-Fe-N <brk/>Low-Carbon Alloy Bar and Wire, Ni-Cr-Fe-Mo-N Alloy Wire, and Ni-Fe-Cr-Mo-N Alloy Bar
• Effective Date: 10-Mar-2002

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
An American National Standard
Designation: A 479/A 479M – 01
Used in USDOE-NE Standards
Standard Specification for
Stainless Steel Bars and Shapes for Use in Boilers and
1
Other Pressure Vessels
This standard is issued under the fixed designation A 479/A 479M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope E 112 Test Methods for Determining the Average Grain
4
2
Size
1.1 This specification covers hot- and cold-finished bars of
5
E 527 Practice for Numbering Metals and Alloys (UNS)
stainless steel, including rounds, squares, and hexagons, and
2.2 Other Document:
hot-rolled or extruded shapes such as angles, tees, and channels
2 SAE J1086 Recommended Practice for Numbering Metals
for use in boiler and pressure vessel construction.
6
and Alloys
NOTE 1—There are standards covering high nickel, chromium, austen-
itic corrosion, and heat-resisting alloy materials. These standards are
3. Ordering Information
under the jurisdiction of ASTM Subcommittee B02.07 and may be found
3.1 It is the responsibility of the purchaser to specify all
in Annual Book of ASTM Standards, Vol 02.04.
requirements that are necessary for material ordered under this
1.2 The values stated in either inch-pound units or SI
specification. Such requirements may include, but are not
(metric) units are to be regarded separately as standards; within
limited to, the following:
the text and tables, the SI units are shown in [brackets]. The
3.1.1 Quantity (weight or number of pieces),
values stated in each system are not exact equivalents; there-
3.1.2 Dimensions, including diameter or thickness (and
fore, each system must be used independent of the other.
width), shape or form, applicable prints or sketches, length,
Combining values from the two systems may result in noncon-
etc.,
formance with the specification.
3.1.3 Type or UNS designation, (Table 1),
1.3 Unless the order specifies the applicable “M” specifica-
3.1.4 ASTM designation and edition year if other than latest
tion designation, the material shall be furnished to the inch-
edition,
pound units.
3.1.5 Heat treated condition (Section 4),
3.1.6 Finish (see Manufacture section of Specification
2. Referenced Documents
A 484/A 484M),
2.1 ASTM Standards:
3.1.7 Supplementary Requirements invoked for special ser-
A 262 Practices for Detecting Susceptibility to Intergranu-
vices (described at the end of this specification),
3
lar Attack in Austenitic Stainless Steels
3.1.8 Whether bars are to be rolled as bars or cut from strip
A 370 Test Methods and Definitions for Mechanical Testing
or plate,
3
of Steel Products
3.1.9 Preparation for delivery (see Preparation for Delivery
A 484/A 484M Specification for General Requirements for
section of Specification A 484/A 484M),
3
Stainless Steel Bars, Billets, and Forgings
3.1.10 Marking requirements (see Marking section of
A 751 Test Methods, Practices, and Terminology for
Specification A 484/A 484M),
3
Chemical Analysis of Steel Products
3.1.11 Surface preparation of shapes (see Manufacture sec-
tion of Specification A 484/A 484M),
3.1.12 The intended use of the material, if the purchaser
considers this useful information.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
NOTE 2—A typical ordering description is as follows: 5000 lb [2000
Stainless Steel and Related Alloys, and is the direct responsibility of Subcommittee
A01.17 on Flat-Rolled and Wrought Stainless Steel Products.
Current edition approved Sept. 10, 2001. Published October 2001. Originally
4
published as A 479 – 62 T. Last previous edition A 479/A 479M – 00. Annual Book of ASTM Standards, Vol 03.01.
2 5
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Annual Book of ASTM Standards, Vol 01.01.
6
cation SA-479/SA-479M in Section II of that Code. Available from Society of Automotive Engineers, 400 Commonwealth Drive,
3
Annual Book of ASTM Standards, Vol 01.03. Warrendale, PA 15096.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A 479/A 479M
kg]; 1.000 in. [25 mm] round bar by 10 to 12 ft [3 to 4 m]; Type 304 or
lished for different applications: Level 1 and Level 2 (see Table
UNS S30400; to Specification A 479 [A 479M]; annealed; centerless
2).
ground; plus any optional supplementary requirements, such as, for
4.1.4 High tensile Type XM-19 shall be in the hot-rolled or
example, special marking instructions.
strain-hardened
...