iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3003-01(2022)

(Test Method)

Standard Test Method for Pressure Mottling and Blocking Resistance of Organic Coatings on Metal Substrates

Standard Test Method for Pressure Mottling and Blocking Resistance of Organic Coatings on Metal Substrates

ABSTRACT
This test method covers the procedures for determining the pressure mottling and sticking, or blocking resistance of organic coatings applied on coil-coated or factory coated metal substrates prior to fabrication. The coated metal is cut into at least four, preferably six, suitably-sized panels which are then subjected to a specified pressure and temperature for a specified time. After the heat is turned off and the specimen cooled, the samples are examined for any signs of sticking or blocking and mottling.
SCOPE
1.1 This test method covers determination of the pressure mottling and sticking, or blocking resistance of organic coatings applied to coil-coated or factory-coated metal prior to fabrication.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
30-Nov-2022
ICS
25.220.60 - Organic coatings
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.53 - Coil Coated Metal
Current Stage
Ref Project

Buy Standard

ASTM D3003-01(2022) - Standard Test Method for Pressure Mottling and Blocking Resistance of Organic Coatings on Metal SubstratesASTM D3003-01(2022) - Standard Test Method for Pressure Mottling and Blocking Resistance of Organic Coatings on Metal Substrates
PreviousNext
Standard
ASTM D3003-01(2022) - Standard Test Method for Pressure Mottling and Blocking Resistance of Organic Coatings on Metal Substrates
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D3003 −01(Reapproved 2022)
Standard Test Method for
Pressure Mottling and Blocking Resistance of Organic
Coatings on Metal Substrates
This standard is issued under the fixed designation D3003; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope specimensareexaminedforanysignsofsticking(orblocking),
and mottling.The results are rated on the 0 to 10 scale and may
1.1 This test method covers determination of the pressure
beusedinacceptingorrejectingthecoatinginaccordancewith
mottling and sticking, or blocking resistance of organic coat-
standards established between the purchaser and the seller.
ings applied to coil-coated or factory-coated metal prior to
fabrication.
4. Apparatus
1.2 The values stated in SI units are to be regarded as the
4.1 Suitable Hydraulic or Mechanical Press or Vise may be
standard. The values given in parentheses are for information
used.Theequipmentshallbecapableofproducingtherequired
only.
test pressure in kilopascals (or pounds-force per square inch)
1.3 This standard does not purport to address all of the
and be equipped with a suitable device for measuring the force
safety concerns, if any, associated with its use. It is the
applied.
responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter-
5. Test Specimens and Conditions
mine the applicability of regulatory limitations prior to use.
5.1 At least four, and preferably six, flat panels shall be cut
1.4 This international standard was developed in accor-
from the coated stock, the age of which shall be within the
dance with internationally recognized principles on standard-
limits agreed upon between the purchaser and the seller.
ization established in the Decision on Principles for the
5.2 Panels should be at least 100 mm by 70 mm (4 in. by
Development of International Standards, Guides and Recom-
2.5 in.) to provide an adequate area for assessing the results.
mendations issued by the World Trade Organization Technical
Where the equipment does not provide adequate pressure,
Barriers to Trade (TBT) Committee.
smaller panels may be used. The minimum recommended size
2. Terminology is 50 mm by 50 mm (2 in. by 2 in.).
2.1 Definitions of Terms Specific to This Standard: 5.3 Use only flat panels. If necessary, file the edges smooth
2.1.1 blocking or sticking, n—the condition wherein coated to ensure maximum contact between the surfaces. When the
surfaces adhere to each other. equipment permits, panels larger than the pressure plates may
be used, thus eliminating any effect from uneven edges. With
2.1.2 pressure mottling, n—film distortion or uneven pattern
this method, the kilopascals (or pounds of force per square
giving a change of gloss and nonuniform appearance. It is
inch)iscalculatedusingonlythepanelareawithinthepressure
usually caused by pressures within a painted coil or stacked
plates.
painted sheets or other painted products.
5.4 The film thickness of the coating under test shall be as
3. Summary of Test Method
specified or agreed upon between the purchaser and the seller.
3.1 The coated metal is cut into suitably sized panels. A
5.5 The coated stock shall be tested under the conditions of
stack of these panels is then subjected to a specified pressure
pressure, temperature, and time mutually agreed upon between
and temperature for a specified time to permit any pressure
the purchaser and the seller. Pressures ranging from 750 kPa to
mottling and sticking or blocking to develop. The applied heat
2400 kPa (110 psi to 350 psi), temperatures from 43 °C to
of the test apparatus is turned off and, after cooling, the
60 °C (110 °F to 140 °F), and times of 2 h to 16 h have been
used.
This test method is under the jurisdiction of ASTM Committee D01 on Paint
and Related Coatings, Materials, andApplications and is the direct responsibility of
Subcommittee D01.53 on Coil Coated Metal. Suitable equipment includes presses and drill press vises modified for use with
Current edition approved Dec. 1, 2022. Published December 2022. Originally a torque wrench if agreed upon between purchaser and seller (Hensley, W. L.,
approved in 1971. Last previous edition approved in 2016 as D3003 – 01 (2016). “Pressure Mottling Test,”Journal of Paint Technology, Vol 40, No. 517, February
DOI: 10.1520/D3003-01R22. 1968, p. 54A).
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D3003−01(2022)
5.6 In the absence of agreed or specified test conditions, a 6.7 Maintain panels that are to be reassessed for a mottling
pressure of 750 kPa 6 35 kPa (110 psi 6 5 psi), a temperature grade in accordance with Table 1 after a 24-h recovery period
of 43 °C 6 1.5 °C (110 °F 6 3 °F), and a time of 16 h shall be at 24 °C 6 3 °C (75 °F 6 5 °F).
used.
6.8 For both properties assign each coating a grade that is
5.7 The total force applied is measured by a suitable gage the arithmetic mean of all panels tested.
and the pounds of force per kilopascals (or square inch) is
7. Report
calculated by dividing the force by the area in square inches of
7.1 Report the following information for each coating:
one side of one panel.
7.1.1
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D2793-99(2024)(Test Method)
Standard Test Method for Block Resistance of Organic Coatings on Wood Panel Substrates

SIGNIFICANCE AND USE
4.1 Coated wood panel products must be stacked face to face or face to back during warehousing, packaging, and transportation without the coated finish sticking (blocking) and becoming damaged. This test method describes a laboratory means of evaluating conditions of blocking using factors of pressure, heat, time and moisture.  
4.2 Degrees of hardness or degrees of cure of organic coatings, or both, can be evaluated using a blocking test.  
4.3 The rate of volatile loss (drying speed) of organic coatings can be evaluated using a blocking test.  
4.4 The effectiveness of protective packaging materials (slip sheets) for organic coatings on wood substrates can be evaluated using a blocking test.
SCOPE
1.1 This test method covers the determination of the block resistance of organic coatings on wood and wood-based panel substrates. Block resistance is the ability of a coating to resist sticking to another surface and to resist any change in appearance when it is pressed against that surface for a prolonged period of time.  
1.2 General methods for determining block resistance are outlined in Sections 6 and 7. Variations inherent in user materials and procedures, however, may dictate adjustments to the general method to improve accuracy. Paragraphs 7.3 and 7.4 provide guidelines for tailoring the general procedure to a user's specific application. Paragraph 7.5 offers a rating methodology.  
1.3 Test Method D2091 should be used for the determination of print resistance or pressure mottling of organic coatings, particularly lacquers, applied to wood-based case goods such as furniture.  
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2134-19(2024)(Test Method)
Standard Test Method for Determining the Hardness of Organic Coatings with a Sward-Type Hardness Rocker

SIGNIFICANCE AND USE
3.1 Sward-type hardness rocker instruments have been used by the coatings industry for more than a half a century as a nondestructive test instrument to measure cure and ultimate surface hardness of organic coatings (see Refs. (1) through (2)).4 This test method is useful within laboratories to quickly screen and measure the surface hardness of candidate coatings.
Note 1: In previous task group work designed to establish an ASTM method for measuring hardness of organic coatings with Sward-type hardness rocker instruments, round-robin test results continually showed poor interlaboratory reproducibility. This lack of interlaboratory agreement could have resulted from dimensional variations among instruments, with the contact rocker rings as the most likely offender in that regard. There are several producers of Sward-type hardness rockers making instruments that differ among themselves in net weight and ring radius. Some of them exceed the measurements and net weight called for in this test method.
SCOPE
1.1 This test method covers the determination of the relative degree of surface hardness of organic coatings using a specific apparatus used in the coatings industry.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This test method does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4708-24(Practice)
Standard Practice for Preparation of Uniform Free Films of Organic Coatings

SIGNIFICANCE AND USE
5.1 Free films are required for conducting tests to evaluate physical and mechanical properties such as tensile and elongation (Test Methods D2370), moisture vapor permeability (Test Methods D1653 and E96/E96M), microbiological activity resistance (Test Method D5590), and other physical properties of organic coatings where the substrate may interfere with the determination.
SCOPE
1.1 This practice covers the preparation of free films of organic coatings for use in determining the physical properties of the coatings.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D7835/D7835M-23(Test Method)
Standard Test Method for Determining the Solvent Resistance of an Organic Coating Using a Mechanical Rubbing Machine

SIGNIFICANCE AND USE
5.1 Many coatings used in the coil coating and other industries achieve a degree of solvent resistance after they have experienced a bake condition characterized by exposure to elevated temperatures in an oven over time. Insufficient bake, or occasionally over bake, may affect the intended chemical bonds or physical curing of the film and result in reduced solvent resistance.  
5.2 The mechanical rubbing machine provides consistent stroke length, rate, pressure, and contact area that are not subject to variables such as human fatigue (see Practice D5402).  
5.3 Factors other than bake can influence degree of solvent resistance of a coated surface. Paint film chemistry and composition, surface preparation, oven dwell time, oven air velocity, ambient oven temperature, oven profiling, film thickness, etc., all are influential. The test solvent used in the rub machine has a significant effect on the number of double rubs measured. Common solvents used for these tests include Methyl Ethyl Ketone (MEK), Methyl Isobutyl Ketone (MIBK), and Isopropyl Alcohol to name a few. The specific solvent to be used and the umber of double rubs to be achieved should be agreed upon between manufacturer and user for any given coating system, thickness, and application.
SCOPE
1.1 This test method covers a mechanical rub method for assessing the solvent resistance of an organic coating that chemically and/or physically changes during the curing process. This technique can be used in the laboratory, in the field, or in the fabricating shop.  
1.2 This test method does not specify the solvent, number of double rubs, or expected test results.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1474/D1474M-13(2023)(Test Method)
Standard Test Methods for Indentation Hardness of Organic Coatings

SIGNIFICANCE AND USE
4.1 Indentation hardness measurements have proven to be useful in rating coatings on rigid substrates for their resistance to mechanical abuse, such as that produced by blows, gouging, and scratching. These measurements do not necessarily characterize the resistance to mechanical abuse of coatings that are required to remain intact when deformed.
SCOPE
1.1 These test methods cover the determination of the indentation hardness of organic materials such as dried paint, varnish, and lacquer coatings, when applied to an acceptable plane rigid surface, for example, metal or glass.  
1.2 Two methods are covered as follows:    
Sections  
Method A—Knoop Indentation Hardness  
6 – 12  
Method B—Pfund Indentation Hardness  
13 – 19  
1.3 Method A, which has the greater precision, provides hardness values in terms of Knoop Hardness Number (KHN). Method B provides hardness in terms of Pfund Hardness Number (PHN). Although the hardness value scales of these methods differ, the methods agree in the ranking of coating hardness.  
1.4 Test Method A of these test methods is similar in content (but not technically equivalent) to ISO 6441-1 and ISO 6441-2.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.6 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D2197-16(2022)(Test Method)
Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion

SIGNIFICANCE AND USE
4.1 Coatings to perform satisfactorily must adhere to the substrates on which they are applied. This test method has been found useful in differentiating the degree of adhesion of coatings to substrates. It is most useful in providing relative ratings for a series of coated panels exhibiting significant differences in adhesion.  
4.2 Studies performed in a laboratory using the loop stylus specified in the previous edition showed meaningful adhesion data were impossible when loads of 10 to 20 kg were required to break the surface of a solvent based coating. The chrome plated loop stylus chattered and skipped across the coating surface when loads of this magnitude were required. Similar meaningless data were obtained when powder coatings were tested that required more than 10 kg to break the surface. Therefore, testing under these conditions is not applicable.
SCOPE
1.1 This test method covers the determination of the adhesion of organic coatings such as paint, varnish, and lacquer when applied to smooth, flat (planar) panel surfaces.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6991-17(2022)(Test Method)
Standard Test Method for Measurements of Internal Stresses in Organic Coatings by Cantilever (Beam) Method

SIGNIFICANCE AND USE
5.1 Stresses in coatings arise as a result of their shrinkage or expansion if expected movements are prevented by coating adhesion to its substrate.  
5.2 There are several causes leading to arrival of stresses in the coatings: film formation (cross-linking, solvent evaporation, etc.); differences in thermal expansion coefficients between coating and substrate; humidity and water absorption; environmental effects (ultraviolet radiation, temperature and humidity), and others.  
5.3 Knowledge of the internal stresses in coatings is very important because they may effect coating performance and service life. If the internal stress exceeds the tensile strength of the film, cracks are formed. If stress exceeds adhesion between coating and substrate, it will reduce adhesion and can lead to delamination of coatings. Quantitative information about stresses in coatings can be useful in coating formulation and recommendations for their application and use.  
5.4 This method has been found useful for air-dry industrial organic coatings but the applicability has not yet been assessed for thin coatings (thickness
SCOPE
1.1 This test method covers the procedure for measurements of internal stresses in organic coatings by using the cantilever (beam) method.  
1.2 This method is appropriate for the coatings for which the modulus of elasticity of substrate (Es) is significantly greater than the modulus of elasticity of coating (Ec) and for which the thickness of substrate is significantly greater than thickness of coating (see Note 7 and Note 8).  
1.3 The stress values are limited by the adhesion values of coating to the substrate and by the tensile strength of the coating, or both.  
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D3363-22(Test Method)
Standard Test Method for Film Hardness by Pencil Test

SIGNIFICANCE AND USE
5.1 Pencil hardness measurements have been used by the coatings industry for many years to determine the hardness of clear and pigmented organic coating films. This test method has also been used to determine the cure of these coatings, especially when using forced dried heat.  
5.2 This test method is convenient in developmental work and in production control testing in a single laboratory. It should be recognized that the results obtained may vary between different laboratories when different manufacturer’s pencils as well as when different substrates are used. To improve test result reproducibility for a specific group of tests, it is recommended to utilize drawing leads or pencils made by the same manufacturer and from the same batch. If drawing leads or pencils from the same manufacturer and from the same batch are not available at the time of subsequent evaluations, it shall be noted on the test report.
Note 3: Using leads or pencils made by different manufacturers or from the same manufacturer but different production batches, may result in significant variation for leads within the same pencil hardness scale.  
5.3 This test method has been found to be useful in providing relative rankings for a series of coatings that exhibit significant differences in film hardness. Caution should be used when attempting to compare coatings of similar film hardness.  
5.4 This test method may not be appropriate for coatings applied to a wood or other softer substrate in which results may be more a function of substrate deformation than coating hardness.  
5.5 If this test method is used as a basis for purchase agreement, maximum precision will be achieved if a given set of referee pencils be agreed upon between the interested parties.
SCOPE
1.1 This test method covers a procedure for rapid, inexpensive determination of the film hardness of an organic coating on a metal or similarly hard substrate in terms of drawing leads or pencil leads of known hardness.  
1.2 This test method is similar in content (but not technically equivalent) to ISO 15184.
Note 1: Other procedures are available to measure permanent deformation of organic coatings under the action of a single point (stylus tip) including but not limited to Test Methods D2197, D5178, and G171.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D968-22(Test Method)
Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive

SIGNIFICANCE AND USE
5.1 Silica sand produces a slower rate of abrasion for organic coatings than that provided by silicon carbide. For some types of coatings, it may also provide greater differentiation.  
5.2 The abrasion resistance scales produced by the two methods differ, but the methods provide approximately the same rankings of coatings for abrasion resistance.  
5.3 Each of the methods has been found useful for rating the abrasion resistance of specific types of coatings. For example Method A (falling sand) has been used for rating floor coatings while Method B (falling silicon carbide) has been used for rating coatings for ship decks.
FIG. 1 Abrasion Test Apparatus
SCOPE
1.1 These test methods cover the determination of the resistance of organic coatings to abrasion produced by abrasive falling onto coatings applied to a plane rigid surface, such as a metal or glass panel.  
1.2 Two test methods based on different abrasives are covered as follows:    
Sections  
Method A—Falling Sand Abrasion Test  
6 – 13  
Method B—Falling Silicon Carbide Abrasion Test  
14 – 21  
1.3 These methods should be restricted to testing in only one laboratory when numerical values are used because of the poor reproducibility of the methods (see 13.1.2 and 21.1.2). Interlaboratory agreement is improved significantly when ranking is used in place of numerical values.  
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses after SI units are for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D1640/D1640M-14(2022)(Test Method)
Standard Test Methods for Drying, Curing, or Film Formation of Organic Coatings

SIGNIFICANCE AND USE
3.1 These test methods can be used to determine the various stages and rates of drying, curing, and film formation of organic coatings for comparing types of coatings, assessing the impact of compositional changes on drying time, or for assessing drying/curing time in the shop or field. Low temperature can significantly slow the drying rate of coatings so low temperature curing agents, catalysts and/or accelerators are often available to aid drying and film formation under cooler temperatures. Method B is designed to evaluate these components and/or to determine the effect of cooler temperatures on drying rates. Conversely, the drying/curing rate of certain coatings can be accelerated under elevated temperature/humidity conditions, while others may be adversely impacted by elevated humidity. Method C is designed to evaluate the effects of elevated temperature and relative humidity conditions on drying, curing, and film formation of paints and coatings. The terms dry or drying, cure or curing, and film formation are used interchangeably throughout this standard.  
3.2 Test Methods A, B and C are limited to a comparison of paints/coatings applied to smooth, non-absorbent substrates and do not reflect the effect of absorption of the paint vehicle into the substrate material.
SCOPE
1.1 These test methods cover the determination of the various stages and rates of film formation in the drying or curing of organic coatings under laboratory controlled conditions of air temperature, (low, ambient and/or elevated) and/or humidity. Procedures for assessing drying under prevailing conditions of temperature and humidity in the shop and field are also described.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off