ASTM B569-09
(Specification)Standard Specification for Brass Strip in Narrow Widths and Light Gage for Heat-Exchanger Tubing
Standard Specification for Brass Strip in Narrow Widths and Light Gage for Heat-Exchanger Tubing
ABSTRACT
This specification establishes the requirements for brass strips in narrow widths and light gages produced from Copper Alloy UNS Nos. C23000, C26000, and C26130 to be used in heat exchanger tubing. The material for manufacture shall be a cast bar, cake, or slab of such purity and soundness as to be suitable for processing by hot working, cold working, and annealing to produce a uniform wrought structure in the finished product. Products shall be produced in tempers H01 (¼ hard), H02 (½ hard), O81 (annealed-to-temper, ¼ hard), and O82 (annealed-to-temper, ½ hard). Products shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (mass, thickness, width, and straightness), mechanical (tensile and yield strengths, and elongation), chemical composition, and grain size requirements.
SCOPE
1.1 This specification establishes the requirements for brass strip in narrow widths and light gages produced from Copper Alloys Nos. C23000, C26000, and C26130.
Note 1—This product is commonly used for the manufacture of thin-wall tubes for water passages in heat exchangers for internal combustion engines and other closed system heat sources.
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.2.1 Exception—Grain size and chemical analysis sampling are stated in SI units.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B569 −09
StandardSpecification for
Brass Strip in Narrow Widths and Light Gage for Heat-
1
Exchanger Tubing
This standard is issued under the fixed designation B569; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* E478 Test Methods for ChemicalAnalysis of CopperAlloys
1.1 This specification establishes the requirements for brass
3. Terminology
strip in narrow widths and light gages produced from Copper
3.1 For definitions of terms related to copper and copper
Alloys Nos. C23000, C26000, and C26130.
alloys, refer to Terminology B846.
NOTE 1—This product is commonly used for the manufacture of
thin-wall tubes for water passages in heat exchangers for internal
4. Ordering Information
combustion engines and other closed system heat sources.
4.1 Include the following information when placing orders
1.2 Units—The values stated in inch-pound units are to be
for products to this specification:
regarded as standard. The values given in parentheses are
4.1.1 ASTM designation and year of issue (for example,
mathematical conversions to SI units that are provided for
B569–XX),
information only and are not considered standard.
4.1.2 Copper [Alloy] UNS No. designation (for example,
1.2.1 Exception—Grain size and chemical analysis sam-
C26000),
pling are stated in SI units.
4.1.3 Temper (Section 7),
4.1.4 Dimensions:thickness,width,length(Section10),and
2. Referenced Documents
4.1.5 Quantity: total weight each form, temper, and size.
2
2.1 ASTM Standards:
4.2 The following options are available and should be
B601 Classification forTemper Designations for Copper and
specified at the time of placing an order when required:
Copper Alloys—Wrought and Cast
4.2.1 Heat identification or traceability details,
B846 Terminology for Copper and Copper Alloys
4.2.2 Certification, and
B950 Guide for Editorial Procedures and Form of Product
4.2.3 Mill test report.
Specifications for Copper and Copper Alloys
E3 Guide for Preparation of Metallographic Specimens
5. Materials and Manufacture
E8/E8M Test Methods for Tension Testing of Metallic Ma-
5.1 Material:
terials
5.1.1 The material of manufacture shall be a form (cast bar,
E29 Practice for Using Significant Digits in Test Data to
cake, or slab) of Copper Alloy UNS No. C23000, C26000, or
Determine Conformance with Specifications
C26130 of such purity and soundness as to be suitable for
E62 Test Methods for Chemical Analysis of Copper and
3
processing into the products prescribed herein.
CopperAlloys (Photometric Methods) (Withdrawn 2010)
5.1.2 In the event heat identification or traceability is
E112 Test Methods for Determining Average Grain Size
required, the purchaser shall specify the details desired.
E255 Practice for Sampling Copper and Copper Alloys for
the Determination of Chemical Composition
NOTE 2—Because of the discontinuous nature of the processing of
castings into wrought products, it is not always practical to identify a
specific casting analysis with a specific quantity of finished material.
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
5.2 Manufacture:
andCopperAlloysandisthedirectresponsibilityofSubcommitteeB05.01onPlate,
Sheet, and Strip.
5.2.1 The product width shall be no greater than 3 in. (76.2
Current edition approved April 1, 2009. Published May 2009. Originally
mm), and thickness shall be less than 0.0181 in. (0.460 mm).
approved in 1972. Last previous edition approved in 2004 as B569 – 04. DOI:
5.2.2 The product shall be manufactured by such hot-
10.1520/B0569-09.
2
working, cold-working, and annealing processes as to produce
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
a uniform wrought structure in the finished product.
Standards volume information, refer to the standard’s Document Summary page on
5.2.2.1 The product shall be hot- or cold-worked to the
the ASTM website.
3
finished size, and subsequently annealed, when required, to
The last approved version of this historical standard is referenced on
www.astm.org. meet the temper properties specified.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B569−09
5.2.3 Edges: 9.3.1 Product furnished to this specification shall conform
5.2.3.1 Slit edges shall be furnished. to the elongation requirements prescribed in Tables 2 and 3 for
the temper and alloy specified in the ordering information
6
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B569–04 Designation: B 569 – 09
Standard Specification for
Brass Strip in Narrow Widths and Light Gage for Heat-
1
Exchanger Tubing
This standard is issued under the fixed designation B 569; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 ThisspecificationestablishestherequirementsforbrassstripinnarrowwidthsandlightgagesproducedfromCopperAlloys
Nos. C23000, C26000, and C26130.
NOTE 1—This product is commonly used for the manufacture of thin-wall tubes for water passages in heat exchangers for internal combustion engines
and other closed system heat sources.
1.2 Units—Thevaluesstatedininch-poundunitsaretoberegardedasstandard,exceptforgrainsize,whichisstatedinSIunits.
The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not
considered standard. —The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are
mathematical conversions to SI units that are provided for information only and are not considered standard.
1.2.1 Exception—Grain size and chemical analysis sampling are stated in SI units.
2. Referenced Documents
2
2.1 ASTM Standards:
B248Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
B601Classification for Temper Designations for Copper and CopperAlloys—Wrought and Cast 601 Classification for Temper
Designations for Copper and Copper AlloysWrought and Cast
B 846 Terminology for Copper and Copper Alloys
B 950 Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys
E3 PracticeGuide for Preparation of Metallographic Specimens
E8 8/E 8M Test Methods for Tension Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance With Specifications Practice for Using
Significant Digits in Test Data to Determine Conformance with Specifications
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E112 Test Methods for Determining Average Grain Size
E 255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E 478 Test Methods for Chemical Analysis of Copper Alloys
3. Terminology
3.1Definitions— For definitions of terms used in this specification, refer to Terminology B846
3.1 For definitions of terms related to copper and copper alloys, refer to Terminology B 846.
3.2Definitions of Terms Specific to This Standard:
3.2.1capable of—thetestneednotbeperformedbytheproducerofthematerial.However,ifsubsequenttestingbythepurchaser
establishes that the material does not meet these requirements, the material shall be subject to rejection.
4. Ordering Information
4.1 Include the following information when placing orders for products to this specification:
4.1.1 ASTM designation and year of issue (for example, B 569–XX),
4.1.2 Copper [Alloy] UNS No. designation (for example, C26000),
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.01 on Plate,
Sheet, and Strip.
Current edition approved MayApril 1, 2004.2009. Published May 2004.2009. Originally approved in 1972. Last previous edition approved in 19982004 as
B569–98.B 569 – 04.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B569–09
4.1.3 Temper (Section 7),
4.1.4 Dimensions: thickness, width, length (Section 10), and
4.1.5 Quantity: total weight each form, temper, and size.
4.2 The following options are available and should be specified at the time of placing an order when required:
4.2.1 Heat identification or traceability details,
4.2.2 Certification, and
4.2.3 Mill test report.
5. Materials and Manufacture
5.1 Material:
5.1.1 The material of manufacture shall be a form (cast bar, cake, or slab) of Copper Alloy UNS No. C23000, C
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B569–04 Designation: B 569 – 09
Standard Specification for
Brass Strip in Narrow Widths and Light Gage for Heat-
1
Exchanger Tubing
This standard is issued under the fixed designation B 569; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 ThisspecificationestablishestherequirementsforbrassstripinnarrowwidthsandlightgagesproducedfromCopperAlloys
Nos. C23000, C26000, and C26130.
NOTE 1—This product is commonly used for the manufacture of thin-wall tubes for water passages in heat exchangers for internal combustion engines
and other closed system heat sources.
1.2 Units—Thevaluesstatedininch-poundunitsaretoberegardedasstandard,exceptforgrainsize,whichisstatedinSIunits.
The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not
considered standard. —The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are
mathematical conversions to SI units that are provided for information only and are not considered standard.
1.2.1 Exception—Grain size and chemical analysis sampling are stated in SI units.
2. Referenced Documents
2
2.1 ASTM Standards:
B248Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
B601Classification for Temper Designations for Copper and CopperAlloys—Wrought and Cast 601 Classification for Temper
Designations for Copper and Copper AlloysWrought and Cast
B 846 Terminology for Copper and Copper Alloys
B 950 Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys
E3 PracticeGuide for Preparation of Metallographic Specimens
E8 8/E 8M Test Methods for Tension Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance With Specifications Practice for Using
Significant Digits in Test Data to Determine Conformance with Specifications
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E112 Test Methods for Determining Average Grain Size
E 255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E 478 Test Methods for Chemical Analysis of Copper Alloys
3. Terminology
3.1Definitions— For definitions of terms used in this specification, refer to Terminology B846
3.1 For definitions of terms related to copper and copper alloys, refer to Terminology B 846.
3.2Definitions of Terms Specific to This Standard:
3.2.1capable of—thetestneednotbeperformedbytheproducerofthematerial.However,ifsubsequenttestingbythepurchaser
establishes that the material does not meet these requirements, the material shall be subject to rejection.
4. Ordering Information
4.1 Include the following information when placing orders for products to this specification:
4.1.1 ASTM designation and year of issue (for example, B 569–XX),
4.1.2 Copper [Alloy] UNS No. designation (for example, C26000),
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.01 on Plate,
Sheet, and Strip.
Current edition approved MayApril 1, 2004.2009. Published May 2004.2009. Originally approved in 1972. Last previous edition approved in 19982004 as
B569–98.B 569 – 04.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B569–09
4.1.3 Temper (Section 7),
4.1.4 Dimensions: thickness, width, length (Section 10), and
4.1.5 Quantity: total weight each form, temper, and size.
4.2 The following options are available and should be specified at the time of placing an order when required:
4.2.1 Heat identification or traceability details,
4.2.2 Certification, and
4.2.3 Mill test report.
5. Materials and Manufacture
5.1 Material:
5.1.1 The material of manufacture shall be a form (cast bar, cake, or slab) of Copper Alloy UNS No. C23000, C
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.