ASTM F2881/F2881M-18

Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications

ABSTRACT
This specification covers test methods and requirements for dual wall polypropylene pipe and fittings. These requirements are intended to provide pipe and fittings suitable for underground use for nonpressure storm sewer systems. This specification also covers pipe and fittings with an interior smooth wall and an annular corrugated profile outer wall.
SCOPE
1.1 This specification covers requirements and test methods for dual wall polypropylene pipe and fittings. The nominal inside diameters covered are 12 to 60 in. [300 to 1500 mm].  
1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure storm sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.  
1.3 This specification covers pipe and fittings with an interior smooth wall and an annular corrugated profile outer wall (Fig. 1).
FIG. 1 Interior Smooth Wall and an Annular Corrugated Profile Outer Wall  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 The following precautionary statement caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Mar-2018
• ICS: 23.040.20 - Plastics pipes
• ICS: 23.040.45 - Plastics fittings
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.62 - Sewer

Relations

• Replaces: ASTM F2881-11(2015) - Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications
• Effective Date: 01-Apr-2018
• Replaced By: ASTM F2881/F2881M-18a - Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications
• Effective Date: 01-Nov-2018
• Referred By: ASTM F2487-21 - Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Corrugated High Density Polyethylene and Polypropylene Pipelines
• Effective Date: 01-Apr-2018
• Referred By: ASTM F2510/F2510M-22 - Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Dual- and Triple-Wall Polyethylene and Polypropylene Pipes
• Effective Date: 01-Apr-2018

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2881/F2881M −18
Standard Specification for
12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall
Pipe and Fittings for Non-Pressure Storm Sewer
1
Applications
ThisstandardisissuedunderthefixeddesignationF2881/F2881M;thenumberimmediatelyfollowingthedesignationindicatestheyear
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This specification covers requirements and test methods
A666 Specification forAnnealed or Cold-WorkedAustenitic
for dual wall polypropylene pipe and fittings. The nominal
Stainless Steel Sheet, Strip, Plate, and Flat Bar
inside diameters covered are 12 to 60 in. [300 to 1500 mm].
D256 Test Methods for Determining the Izod Pendulum
1.2 The requirements of this specification are intended to
Impact Resistance of Plastics
provide pipe and fittings suitable for underground use for
D618 Practice for Conditioning Plastics for Testing
non-pressure storm sewer systems. Pipe and fittings produced D638 Test Method for Tensile Properties of Plastics
in accordance with this specification shall be installed in D790 Test Methods for Flexural Properties of Unreinforced
and Reinforced Plastics and Electrical Insulating Materi-
compliance with Practice D2321.
als
1.3 This specification covers pipe and fittings with an
D792 Test Methods for Density and Specific Gravity (Rela-
interior smooth wall and an annular corrugated profile outer
tive Density) of Plastics by Displacement
wall (Fig. 1).
D1238 Test Method for Melt Flow Rates of Thermoplastics
by Extrusion Plastometer
1.4 Units—The values stated in either SI units or inch-
D1505 Test Method for Density of Plastics by the Density-
pound units are to be regarded separately as standard. The
Gradient Technique
values stated in each system may not be exact equivalents;
D1600 Terminology forAbbreviatedTerms Relating to Plas-
therefore,eachsystemshallbeusedindependentlyoftheother.
tics
Combining values from the two systems may result in non-
D2122 Test Method for Determining Dimensions of Ther-
conformance with the standard.
moplastic Pipe and Fittings
1.5 The following precautionary statement caveat pertains D2321 PracticeforUndergroundInstallationofThermoplas-
tic Pipe for Sewers and Other Gravity-Flow Applications
only to the test method portion, Section 7, of this specification.
D2412 Test Method for Determination of External Loading
This standard does not purport to address all of the safety
Characteristics of Plastic Pipe by Parallel-Plate Loading
concerns, if any, associated with its use. It is the responsibility
D2444 Practice for Determination of the Impact Resistance
of the user of this standard to establish appropriate safety,
of Thermoplastic Pipe and Fittings by Means of a Tup
health, and environmental practices and determine the appli-
(Falling Weight)
cability of regulatory limitations prior to use.
D2990 Test Methods for Tensile, Compressive, and Flexural
1.6 This international standard was developed in accor-
Creep and Creep-Rupture of Plastics
dance with internationally recognized principles on standard-
D3212 Specification for Joints for Drain and Sewer Plastic
ization established in the Decision on Principles for the
Pipes Using Flexible Elastomeric Seals
Development of International Standards, Guides and Recom-
D3895 Test Method for Oxidative-Induction Time of Poly-
mendations issued by the World Trade Organization Technical
olefins by Differential Scanning Calorimetry
Barriers to Trade (TBT) Committee.
D4101 Classification System and Basis for Specification for
Polypropylene Injection and Extrusion Materials
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
2
Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved April 1, 2018. Published May 2018. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved in 2011. Last previous edition approved in 2015 as F2881–11(2015). DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F2881–18. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2881/F2881M − 18
FIG. 1 Interior Smooth Wall and an Annular Corrugated Profile Outer Wall
D4218 Test Method for Determination of Carbon Black 3.2.2 silt-tight joint, n—Joint that prevents the passage of
Content in Polyethylene Compo
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2881 − 11 (Reapproved 2015) F2881/F2881M − 18
Standard Specification for
12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall
Pipe and Fittings for Non-Pressure Storm Sewer
1
Applications
This standard is issued under the fixed designation F2881;F2881/F2881M; the number immediately following the designation indicates
the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification covers requirements and test methods for dual wall polypropylene pipe and fittings. The nominal inside
diameters covered are 12 to 60 in. [300 to 1500 mm].
1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure
storm sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice
D2321.
1.3 This specification covers pipe and fittings with an interior smooth wall and an annular corrugated profile outer wall (Fig.
1).
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the standard.
1.5 The following precautionary statement caveat pertains only to the test method portion, Section 7, of this specification. This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability
of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A666 Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.
Current edition approved Aug. 1, 2015April 1, 2018. Published November 2015May 2018. Originally approved in 2011. Last previous edition approved in 20112015 as
F2881F2881–11(2015).–11. DOI: 10.1520/F2881–11R15.10.1520/F2881–18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2881/F2881M − 18
FIG. 1 Interior Smooth Wall and an Annular Corrugated Profile Outer Wall
D2990 Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
D3212 Specification for Joints for Drai
...