ASTM F468M-01

Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]

SCOPE
1.1 This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs in nominal thread diameters M6 to M36 inclusive manufactured from a number of alloys in common use and intended for general service applications.  
1.2 Unless otherwise specified, nuts used on these bolts, cap screws, and studs shall conform to the requirements of Specification F467M. Nuts shall be of the same alloy group as the fastener on which they are used, and shall have a specified minimum proof stress equal to or greater than the specified minimum tensile strength stress of the fastener on which they are used.
Note 1—This specification is the metric companion of Specification F468.

General Information

• Status: Historical
• Publication Date: 09-Oct-2001
• ICS: 21.060.10 - Bolts, screws, studs
• Technical Committee: F16 - Fasteners
• Drafting Committee: F16.04 - Nonferrous Fasteners

Relations

• Replaces: ASTM F468M-98 - Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
• Effective Date: 10-Oct-2001
• Replaced By: ASTM F468M-01a - Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
• Effective Date: 10-Oct-2001
• Referred By: ASTM B745/B745M-15(2021) - Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains
• Effective Date: 10-Oct-2001
• Referred By: ASTM F467M-06a(2018) - Standard Specification for Nonferrous Nuts for General Use (Metric)
• Effective Date: 10-Oct-2001
• Referred By: ASTM B746/B746M-22 - Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
• Effective Date: 10-Oct-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: F 468M – 01
METRIC
Standard Specification for
Nonferrous Bolts, Hex Cap Screws, and Studs for General
1
Use [Metric]
This standard is issued under the fixed designation F 468M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope E 8M Test Methods of Tension Testing of Metallic Materi-
6
als [Metric]
1.1 This specification covers the requirements for commer-
E 18 Test Methods for Rockwell Hardness and Rockwell
cial wrought nonferrous bolts, hex cap screws, and studs in
6
Superficial Hardness of Metallic Materials
nominal thread diameters M6 to M36 inclusive manufactured
E 29 Practice for Using Significant Digits in Test Data to
from a number of alloys in common use and intended for
7
Determine Conformance with Specifications
general service applications.
E 34 Test Methods for Chemical Analysis of Aluminum and
1.2 Unless otherwise specified, nuts used on these bolts, cap
8
Aluminum Base Alloys
screws, and studs shall conform to the requirements of Speci-
E 38 Methods for Chemical Analysis of Nickel-Chromium
fication F 467M. Nuts shall be of the same alloy group as the
9
and Nickel-Chromium-Iron Alloys
fastener on which they are used, and shall have a specified
8
E 53 Test Methods for Chemical Analysis of Copper
minimum proof stress equal to or greater than the specified
E 54 Test Methods for Chemical Analysis of Special
minimum tensile strength stress of the fastener on which they
8
Brasses and Bronzes
are used.
E 55 Practice for Sampling Wrought Nonferrous Metals and
NOTE 1—This specification is the metric companion of Specification
Alloys for Determination of Chemical Compo-
F 468.
8
sition
E 62 Test Methods for Chemical Analysis of Copper and
2. Referenced Documents
8
Copper Alloys (Photometric Methods)
2.1 ASTM Standards:
E 75 Test Methods for Chemical Analysis of Copper-Nickel
B 154 Test Method for Mercurous Nitrate Test for Copper
8
and Copper-Nickel-Zinc Alloys
2
and Copper Alloys
E 76 Test Methods for Chemical Analysis of Nickel-Copper
B 193 Test Method for Resistivity of Electrical Conductor
8
Alloys
3
Materials
E 92 Test Method for Vickers Hardness of Metallic Mate-
B 211M Specification for Aluminum and Aluminum-Alloy
6
rials
4
Bar, Rod, and Wire [Metric]
E 101 Test Method for Spectrographic Analysis of Alumi-
B 565 Test Method for Shear Testing of Aluminum and
num and Aluminum Alloys by the Point-to-Plane Tech-
Aluminum-Alloy Rivets and Cold-Heading Wire and
10
nique
4
Rods
E 120 Test Methods for Chemical Analysis of Titanium and
5
D 3951 Practice for Commercial Packaging
8
Titanium Alloys
11
E 165 Test Method for Liquid Penetrant Examination
E 227 Test Method for Optical Emission Spectrometric
1 Analysis of Aluminum and Aluminum Alloys by the
This specification is under the jurisdiction of ASTM Committee F16 on
8
Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous Point-to-Plane Technique
Fasteners.
Current edition approved Apr. 10, 2001. Published June 2001. Originally
published as F 468M – 79. Last previous edition F 468M – 98.
6
2
Annual Book of ASTM Standards, Vol 03.01.
Annual Book of ASTM Standards, Vol 02.01.
7
3
Annual Book of ASTM Standards, Vol 14.02.
Annual Book of ASTM Standards, Vol 02.03.
8
4
Annual Book of ASTM Standards, Vol 03.05.
Annual Book of ASTM Standards, Vol 02.02.
9
5
Discontinued 1989;Replaced by E 350.
Annual Book of ASTM Standards, Vol 15.09.
10
Discontinued; see 1995 Annual Book of ASTM Standards, Vol 03.05.
11
Annual Book of ASTM Standards, Vol 03.03.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F 468M
E 354 Test Methods for Chemical Analysis of High- 4.1.1 The bolts, cap screws, and studs shall be manufactured
Temperature, Electrical, Magnetic, and Other Similar Iron, from material having a chemical composition conforming to
8
Nickel, and Cobalt Alloys the requirements in Table 1 and capable of developing the
E 478 Test Methods for Chemical Analysis of Copper required mechanical properties for the specified alloy in the
8
Alloys finished fastener.
E 1409 Test Method for Determination of Oxygen in Tita-
4.1.2 The starting condition of the raw material shall be at
nium and Titanium Alloys by the Inert Gas Fusion Tech-
the discretion of the fastener manufacturer but shall be such
8
nique
that the finished products conform to all of the specified
F 467M Specification for Nonferrous Nuts for General Use
requirements.
12
[
...