ASTM D3035-14
(Specification)Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
ABSTRACT
This specification covers polyethylene (PE) pipes made in thermoplastic pipe dimension ratios based on outside diameter, and pressure rated for water. All pipes produced under this specification may be used for the transport of water, industrial process liquids, effluents, slurries, municipal sewage, etc. Included are criteria for classifying PE plastic pipe materials and PE plastic pipe, and a system of nomenclature for PE plastic pipe. PE pipes shall be evaluated by the test procedures given herein, and shall conform to specified requirements for workmanship, dimensions, sustained pressure at ambient and elevated temperatures, hydrostatic burst pressure, tensile strength at yield, and environmental stress cracking.
SCOPE
1.1 This specification covers polyethylene (PE) pipe made in thermoplastic pipe dimension ratios based on outside diameter and pressure rated for water (see Appendix X1). Included are requirements for polyethylene compounds and PE plastic pipe, a system of nomenclature for PE plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained pressure, and burst pressure. Methods of marking are also given.
1.2 All pipes produced under this specification may be used for the transport of water, industrial process liquids, effluents, slurries, municipal sewage, etc. The user should consult the manufacturer to determine whether the material being transported is compatible with polyethylene pipe and will not affect the service life beyond limits acceptable to the user.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D3035 −14 AnAmerican National Standard
Standard Specification for
Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled
1
Outside Diameter
This standard is issued under the fixed designation D3035; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D1598 Test Method for Time-to-Failure of Plastic Pipe
Under Constant Internal Pressure
1.1 This specification covers polyethylene (PE) pipe made
D1599 Test Method for Resistance to Short-Time Hydraulic
in thermoplastic pipe dimension ratios based on outside diam-
Pressure of Plastic Pipe, Tubing, and Fittings
eter and pressure rated for water (see Appendix X1). Included
D1600 Terminology forAbbreviatedTerms Relating to Plas-
are requirements for polyethylene compounds and PE plastic
tics
pipe, a system of nomenclature for PE plastic pipe, and
D2122 Test Method for Determining Dimensions of Ther-
requirements and test methods for materials, workmanship,
dimensions, sustained pressure, and burst pressure. Methods of moplastic Pipe and Fittings
D2290 Test Method for Apparent Hoop Tensile Strength of
marking are also given.
Plastic or Reinforced Plastic Pipe
1.2 All pipes produced under this specification may be used
D2837 Test Method for Obtaining Hydrostatic Design Basis
for the transport of water, industrial process liquids, effluents,
forThermoplasticPipeMaterialsorPressureDesignBasis
slurries, municipal sewage, etc. The user should consult the
for Thermoplastic Pipe Products
manufacturer to determine whether the material being trans-
D3350 Specification for Polyethylene Plastics Pipe and Fit-
ported is compatible with polyethylene pipe and will not affect
tings Materials
the service life beyond limits acceptable to the user.
F412 Terminology Relating to Plastic Piping Systems
1.3 The values stated in inch-pound units are to be regarded
2.2 NSF International Standards:
as standard. The values given in parentheses are mathematical
NSF/ANSI Standard No. 14 for Plastic Piping Components
conversions to SI units that are provided for information only
3
and Related Materials
and are not considered standard.
NSF/ANSI Standard No. 61 for Drinking Water System
1.4 The following safety hazards caveat pertains only to the
3
Components—Health Effects
test methods portion, Section 7, of this specification:This
standard does not purport to address all of the safety concerns,
2.3 Other Documents:
if any, associated with its use. It is the responsibility of the user
TR-4 Listing of Hydrostatic Design Bases (HDB), Strength
of this standard to establish appropriate safety and health
Design Bases (SDB), Pressure Design Bases (PDB) and
practices and determine the applicability of regulatory limita-
Minimum Required Strength (MRS) Ratings for Thermo-
4
tions prior to use.
plastic Piping Materials or Pipe
5
APWA Uniform Color Code
2. Referenced Documents
2
2.1 ASTM Standards:
3. Terminology
D618 Practice for Conditioning Plastics for Testing
3.1 Definitions—Definitions are in accordance with Termi-
D1238 Test Method for Melt Flow Rates of Thermoplastics
nology F412, and abbreviations are in accordance with Termi-
by Extrusion Plastometer
nology D1600, unless otherwise specified.
3.2 Definitions of Terms Specific to This Standard:
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.26 on Olefin
Based Pipe.
Current edition approved March 1, 2014. Published March 2014. Originally
ε2
3
approved in 1972. Last previous edition approved in 2012 as D3035 – 12 . DOI: Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd.,Ann
10.1520/D3035-14. Arbor, MI 48113-0140, http://www.nsf.org.
2 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or .Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Irving, TX 75062, http://www.plasticpipe.org.
5
Standards volume information, refer to the standard’s Document Summary page on APWA, 2345 Grand Boulevard, Suite 500, Kansas City, MO 64018-2641,
the ASTM website. http://www.apwa.net.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3035−14
TABLE 1 Polyethylene Compound Requirements
Material Designation
PE1404 PE2708 PE3608 PE4608 PE4710
Requirement Required Value
HDB at 140ºF (60ºC), psi
(MPa),
A B B B B
800 (5.5) 800 (5.5)
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´2
Designation: D3035 − 12 D3035 − 14 An American National Standard
Standard Specification for
Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled
1
Outside Diameter
This standard is issued under the fixed designation D3035; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1 E
ε NOTE—Editorially corrected Table 1. Removed blank footnote in November 2012.
2
ε NOTE—Table 1 alignment was editorially corrected in December 2013.
1. Scope*
1.1 This specification covers polyethylene (PE) pipe made in thermoplastic pipe dimension ratios based on outside diameter and
pressure rated for water (see Appendix X1). Included are requirements for polyethylene compounds and PE plastic pipe, a system
of nomenclature for PE plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained
pressure, and burst pressure. Methods of marking are also given.
1.2 All pipes produced under this specification may be used for the transport of water, industrial process liquids, effluents,
slurries, municipal sewage, etc. The user should consult the manufacturer to determine whether the material being transported is
compatible with polyethylene pipe and will not affect the service life beyond limits acceptable to the user.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification:This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1603 Test Method for Carbon Black Content in Olefin Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2290 Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
D2837 Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for
Thermoplastic Pipe Products
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
D4218 Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
F412 Terminology Relating to Plastic Piping Systems
2.2 NSF International Standards:
3
NSF/ANSI Standard No. 14 for Plastic Piping Components and Related Materials
3
NSF/ANSI Standard No. 61 for Drinking Water System Components—Health Effects
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.26 on Olefin Based
Pipe.
Current edition approved July 1, 2012March 1, 2014. Published October 2012March 2014. Originally approved in 1972. Last previous edition approved in 20102012 as
ε2
D3035 – 10.D3035 – 12 . DOI: 10.1520/D3035-12.10.1520/D3035-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from the National Sanitation Foundation, P.O. Box 1468, NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48106.48113-0140,
http://www.nsf.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3035 − 14
2.3 Other Documents:
TR-4 Listing of Hydrostatic Design Bases (HDB), Strength Design Bases (SDB), Pressure Design Bases (PDB
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.