ASTM F1488-09
(Specification)Standard Specification for Coextruded Composite Pipe
Standard Specification for Coextruded Composite Pipe
ABSTRACT
This specification covers coextruded composite pipe, produced by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die. Coextruded composite pipe conforming to the requirements prescribed are used for different applications: IPS Schedule 40 Series-coextruded composite pipe is used for above or below ground installation for communication conduit, electrical conduit, drain, waste, and vent pipe, and plastic underdrain systems for highway, airport, and similar drainage, where a Schedule 40 IPS is required; IPS-DR-PS Series-coextruded composite pipe is used for above or below ground installation for communication conduit, electrical conduit, and drain, waste, and vent pipe; and Sewer and Drain DR-PS Series-coextruded composite pipe is used for gravity flow sewer and drain pipe, and plastic underdrain systems for highway, airport, and similar drainage. The pipe stiffness, impact resistance, and bond strength shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers coextruded composite pipe, produced by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die.
1.1.1 Materials listed in the material section are permitted to be used in any layer of the coextruded composite pipe. When coextruded composite pipe is produced with three layers, the middle layer is permitted to be solid or thermally foamed.
1.1.2 The function of this specification is to provide standardization of product, to produce technical data, and to serve as a purchasing guide.
1.2 Compounds that do not meet the requirements of the material section are excluded.
1.3 The coextruded composite pipe is permitted to be perforated in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.4 The coextruded composite pipe is permitted to be belled for joining by solvent cementing or belled for joining by an elastomeric seal (gaskets), in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.5 Recommendations for storage, joining, installation, and rationale are listed in Appendixes X1, X2, X3, and X4, respectively.
1.6 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. A companion standard written in SI units is under development.
1.7 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—Related specifications are as follows: D 2661, D 2665, D 2729, D 2750, D 2751, D 2949, D 3034, F 512, F 628, F 758, F 789, and F 891.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F1488 – 09
Standard Specification for
1
Coextruded Composite Pipe
This standard is issued under the fixed designation F1488; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (ϵ) indicates an editorial change since the last revision or reapproval.
D2750, D2751, D2949, D3034, F512, F628, F758, F789, and F891.
1. Scope
1.1 This specification covers coextruded composite pipe,
2. Referenced Documents
produced by a coextrusion die system, in which the concentric
2.1 The following standards contain provisions which,
layers are formed and combined before exiting the die.
thoughreferencedinthisspecification,constituteprovisionsof
1.1.1 Materialslistedinthematerialsectionarepermittedto
this specification. All standards are subject to revision and
be used in any layer of the coextruded composite pipe. When
parties using this specification shall reference the most recent
coextruded composite pipe is produced with three layers, the
edition of the standards listed as follows.
middle layer is permitted to be solid or thermally foamed.
2
2.2 ASTM Standards:
1.1.2 The function of this specification is to provide stan-
D618 Practice for Conditioning Plastics for Testing
dardization of product, to produce technical data, and to serve
D696 Test Method for Coefficient of Linear Thermal Ex-
as a purchasing guide.
pansion of Plastics Between Ø30°C and 30°C with a
1.2 Compounds that do not meet the requirements of the
Vitreous Silica Dilatometer
material section are excluded.
D883 Terminology Relating to Plastics
1.3 The coextruded composite pipe is permitted to be
D1600 Terminology for Abbreviated Terms Relating to
perforated in accordance with any specified standard or by
Plastics
agreement between the purchaser and the supplier.
3
D1898 Standard Practice for Sampling of Plastics
1.4 Thecoextrudedcompositepipeispermittedtobebelled
D1972 Practice for Generic Marking of Plastic Products
for joining by solvent cementing or belled for joining by an
D2122 Test Method for Determining Dimensions of Ther-
elastomeric seal (gaskets), in accordance with any specified
moplastic Pipe and Fittings
standard or by agreement between the purchaser and the
D2235 Specification for Solvent Cement for Acrylonitrile-
supplier.
Butadiene-Styrene (ABS) Plastic Pipe and Fittings
1.5 Recommendations for storage, joining, installation, and
D2321 Practice for Underground Installation of Thermo-
rationale are listed in Appendixes X1, X2, X3, and X4,
plastic Pipe for Sewers and Other Gravity-Flow Applica-
respectively.
tions
1.6 Thevaluesstatedininch-poundunitsaretoberegarded
D2412 Test Method for Determination of External Loading
asstandard.Nootherunitsofmeasurementareincludedinthis
Characteristics of Plastic Pipe by Parallel-Plate Loading
standard. A companion standard written in SI units is under
D2444 Test Method for Determination of the Impact Resis-
development.
tance of Thermoplastic Pipe and Fittings by Means of a
1.7 Thetextofthisspecificationreferencesnotes,footnotes,
Tup (Falling Weight)
and appendixes which provide explanatory material. These
D2564 Specification for Solvent Cements for Poly(Vinyl
notesandfootnotes(excludingthoseintablesandfigures)shall
Chloride) (PVC) Plastic Piping Systems
not be considered as requirements of this specification.
D2661 Specification for Acrylonitrile-Butadiene-Styrene
1.8 This standard does not purport to address all of the
(ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe
safety concerns, if any, associated with its use. It is the
and Fittings
responsibility of the user of this standard to establish appro-
D2665 SpecificationforPoly(VinylChloride)(PVC)Plastic
priate safety and health practices and determine the applica-
Drain, Waste, and Vent Pipe and Fittings
bility of regulatory limitations prior to use.
D2729 SpecificationforPoly(VinylChloride)(PVC)Sewer
NOTE 1—Related specifications are as follows: D2661, D2665, D2729,
Pipe and Fittings
D2750 Specification for Acrylonitrile- Butadiene-Sytrene
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.11 on
2
Composite. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Aug. 1, 2009. Published August 2009. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1994. Last previous edition approved in 2003 as F1488–03. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F1488-09. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 1
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F 1488–03 Designation: F 1488 – 09
Standard Specification for
1
Coextruded Composite Pipe
This standard is issued under the fixed designation F 1488; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers coextruded composite pipe, produced by a coextrusion die system, in which the concentric layers
are formed and combined before exiting the die.
1.1.1 Materials listed in the material section are permitted to be used in any layer of the coextruded composite pipe. When
coextruded composite pipe is produced with three layers, the middle layer is permitted to be solid or thermally foamed.
1.1.2 The function of this specification is to provide standardization of product, to produce technical data, and to serve as a
purchasing guide.
1.2 Compounds that do not meet the requirements of the material section are excluded.
1.3 The coextruded composite pipe is permitted to be perforated in accordance with any specified standard or by agreement
between the purchaser and the supplier.
1.4 The coextruded composite pipe is permitted to be belled for joining by solvent cementing or belled for joining by an
elastomeric seal (gaskets), in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.5 Recommendationsforstorage,joining,installation,andrationalearelistedinAppendixesX1,X2,X3,andX4,respectively.
1.6The values stated in inch-pound units are to be regarded as the standard.Acompanion standard written in SI units is under
development.
1.6 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this
standard. A companion standard written in SI units is under development.
1.7 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
NOTE1—Relatedspecificationsareasfollows:D2661,D2665,D2729,D2750,D2751,D2949,D3034,F512,F628,F758,F789,andF891. 1—Related
specifications are as follows: D2661, D2665, D2729, D2750, D2751, D2949, D3034, F512, F628, F758, F789, and F891.
2. Referenced Documents
2.1 The following standards contain provisions which, though referenced in this specification, constitute provisions of this
specification.All standards are subject to revision and parties using this specification shall reference the most recent edition of the
standards listed as follows.
2
2.2 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D696 Test Method for Coefficient of LinearThermal Expansion of Plastics Between −30°C30C and 30°C30C with aVitreous
Silica Dilatometer
D883 Terminology Relating to Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
3
D 1898 Standard Practice for Sampling of Plastics
D1972 Practice for Generic Marking of Plastic Products
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.11 on Composite.
´1
Current edition approved Aug. 10, 2003. Published September 2003. Originally approved in 1994. Last previous edition approved in 2000 as F 1488–00 .
Current edition approved Aug. 1, 2009. Published August 2009. Originally approved in 1994. Last previous edition approved in 2003 as F1488–03.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
, Vol 08.01.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.