iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM B775-01

(Specification)

Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe

Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe

SCOPE
1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:Title of SpecificationASTM DesignationWelded UNS N08020, N08024, and N08026 Alloy PipeB 464Welded Nickel-Iron-Chromium Alloy PipeB 514Welded Nickel-Chromium-Iron-Alloy (UNS N06600, UNS N06603, UNS N06025 and UNS N06045) PipeB 517Welded Nickel and Nickel-Cobalt Alloy PipeB 619UNS N08904, UNS N08925, and UNS N08926 Welded PipeB 673UNS N08367 Welded PipeB 675Nickel-Alloy (UNS N06625, N06219, and N08825) Welded PipeB 705Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded PipeB 723Welded Nickel (UNS N02200/UNS N02201) and Nickel Copper Alloy (UNS N04400) PipeB 725
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

General Information

Status
Historical
Publication Date
09-Nov-2001
ICS
77.150.40 - Nickel and chromium products
Technical Committee
B02 - Nonferrous Metals and Alloys
Drafting Committee
B02.07 - Refined Nickel and Cobalt and Their Alloys
Current Stage
Ref Project

Relations

Replaces
ASTM B775-00 - Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
Effective Date
10-Nov-2001
Replaced By
ASTM B775-02 - Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
Effective Date
10-Oct-2002
Referred By
ASTM B619/B619M-19 - Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe
Effective Date
10-Nov-2001
Referred By
ASTM B514-05(2019) - Standard Specification for Welded Nickel-Iron-Chromium Alloy Pipe
Effective Date
10-Nov-2001
Referred By
ASTM B464/B464M-15(2020) - Standard Specification for Welded UNS N08020 Alloy Pipe
Effective Date
10-Nov-2001
Referred By
ASTM B710-20ae1 - Standard Specification for Nickel-Iron-Chromium-Silicon Alloy Welded Pipe
Effective Date
10-Nov-2001
Referred By
ASTM B546-19 - Standard Specification for Electric Fusion-Welded Ni-Cr-Co-Mo Alloy, Ni-Fe-Cr-Si Alloy, Ni-Cr-Fe-Al Alloy, Ni-Cr-Fe Alloy, and Ni-Cr-Fe-Si Alloy Pipe
Effective Date
10-Nov-2001
Referred By
ASTM B675-22 - Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloy Welded Pipe
Effective Date
10-Nov-2001
Referred By
ASTM B673-21 - Standard Specification for Nickel-Iron-Chromium-Molybdenum and Iron-Nickel-Chromium-Molybdenum-Copper Welded Pipe
Effective Date
10-Nov-2001
Referred By
ASTM B725-22 - Standard Specification for Welded Nickel and Nickel Copper Alloy Pipe
Effective Date
10-Nov-2001
Referred By
ASTM B517-19 - Standard Specification for Welded Nickel-Chromium-Iron-Alloy Pipe
Effective Date
10-Nov-2001
Referred By
ASTM B723-20 - Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy Welded Pipe
Effective Date
10-Nov-2001
Referred By
ASTM B705-17 - Standard Specification for Nickel-Alloy (UNS N06625, N06219 and N08825) Welded Pipe
Effective Date
10-Nov-2001

Buy Standard

ASTM B775-01 - Standard Specification for General Requirements for Nickel and Nickel Alloy Welded PipeASTM B775-01 - Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
PreviousNext
Technical specification
ASTM B775-01 - Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: B 775 – 01
Standard Specification for
General Requirements for Nickel and Nickel Alloy Welded
1
Pipe
This standard is issued under the fixed designation B 775; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope E 29 Practice for Using Significant Digits in Test Data to
4
Determine Conformance with Specifications
1.1 This specification contains various requirements that,
5
E 39 Test Methods for Chemical Analysis of Nickel
with the exception of Section 5 and Section 10, are mandatory
E 76 Test Methods for Chemical Analysis of Nickel Copper
requirements to the following ASTM nickel and nickel alloy,
6
2
Alloys
longitudinally welded piping specifications:
E 112 Test Methods for Determining the Average Grain
ASTM
3
2
Size
Title of Specification Designation
E 213 Practice for Ultrasonic Examination of Metal Pipe
Welded UNS N08020, N08024, and N08026 Alloy Pipe B 464
7
and Tubing
Welded Nickel-Iron-Chromium Alloy Pipe B 514
E 426 Practice for Electromagnetic (Eddy-Current) Exami-
Welded Nickel-Chromium-Iron-Alloy (UNS N06600, B 517
UNS N06603, UNS N06025 and UNS N06045) Pipe
nation of Seamless and Welded Tubular Products, Austen-
Welded Nickel and Nickel-Cobalt Alloy Pipe B 619
7
itic Stainless Steel and Similar Alloys
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe B 673
E 571 Practice for Electromagnetic (Eddy-Current) Exami-
UNS N08367 Welded Pipe B 675
7
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded B 705
nation of Nickel and Nickel Alloy Tubular Products
Pipe
E 1473 Test Methods for Chemical Analysis of Nickel,
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe B 723
6
Welded Nickel (UNS N02200/UNS N02201) and Nickel B 725 Cobalt, and High-Temperature Alloys
8
Copper Alloy (UNS N04400) Pipe
2.2 ANSI Standards:
B 1.20.1 Pipe Threads
1.2 One or more of the test requirements of Section 5 apply
B 36.10 Welded and Seamless Wrought Steel Pipe
only if specifically stated in the product specification or in the
B 36.19 Stainless Steel Pipe
purchase order.
1.3 In case of conflict between a requirement of the product
3. Terminology
specification and a requirement of this general specification,
3.1 Definitions:
only the requirement of the product specification needs to be
3.1.1 average diameter—the average of the maximum and
satisfied.
minimum outside diameters, as determined at any one cross
1.4 The values stated in inch-pound units are to be regarded
section of the pipe.
as the standard. The values given in parentheses are for
3.1.2 nominal wall—a specified wall thickness with a plus
information only.
or minus tolerance from the specified thickness.
2. Referenced Documents
3.1.3 welded pipe—a round hollow produced by forming
flat stock and joining the single longitudinal seam by welding,
2.1 ASTM Standards:
and produced to the particular dimensions commercially
B 880 Specification for General Requirements for Chemical
known as pipe sizes (NPS).
Check Analysis Limits for Nickel, Nickel Alloys and
2
Cobalt Alloys
4. Chemical Composition
3
E 8 Test Methods for Tension Testing of Metallic Materials
4.1 In case of disagreement, the chemical composition shall
E 18 Test Methods for Rockwell Hardness and Rockwell
3
be determined in accordance with the following methods:
Superficial Hardness of Metallic Materials
1
This specification is under the jurisdiction of ASTM Committee B02 on
4
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee Annual Book of ASTM Standards, Vol 14.02.
5
B02.07 on Refined Nickel and Cobalt and Their Alloys. Discontinued; See Annual Book of ASTM Standards, Vol 03.05.
6
Current edition approved Nov. 10, 2001. Published January 2002. Originally Annual Book of ASTM Standards, Vol 03.05.
7
published as B 775 – 87. Last previous edition B 775 – 00. Annual Book of ASTM Standards, Vol 03.03.
2 8
Annual Book of ASTM Standards, Vol 02.04. Available from American National Standards Institute, 11 W. 42nd St., 13th
3
Annual Book of ASTM Standards, Vol 03.01. Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
B 775
calibration standard shall contain, at the option of the manu-
UNS No. Prefixes ASTM Method
N02 E 39
facturer, any one of the following discontinuities to establish a
N04 E 76
minimum sensitivity level for rejection. The discontinuity shall
N06,
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM B472-23(Specification)
Standard Specification for Nickel Alloy Billets and Bars for Reforging

ABSTRACT
This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, and UNS R30556 nickel alloy billets and bars for reforging. The products shall be hot worked from ingots by rolling, forging, extruding, hammering, or pressing. The material shall conform to the chemical composition requirements prescribed by the reference material. The chemical composition of the material shall be determined by chemical analysis in accordance with test method E1473.
SCOPE
1.1 This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N10362, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, UNS N06699, and UNS R305562 billets and bars for reforging.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM B574-23(Specification)
Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod and Bar

ABSTRACT
This specification2 covers rod of low-carbon nickel-chromium- molybdenum alloys (UNS N10276, N06022, N06035, N06455, N06058, and N06059), low-carbon nickel-molybdenum- chromium-tantalum (UNS N06210), low-carbon nickel-chromium-molybdenum-copper alloy (UNS N06200), and low-carbon nickel-chromium-molybdenum-tungsten (UNS N06686), for use in general corrosive service. Product and chemical analyses shall be performed on the materials and shall conform to the required chemical composition in molybdenum, chromium, iron, tungsten, cobalt, carbon, silicon, manganese, vanadium, phosphorus, sulfur, titanium, nickel, aluminum, copper, and tantalum. Tension test shall be performed and shall comply to required mechanical properties for hot or cold finished, solution annealed rods such as tensile strength, yield strength, and elongation.
SCOPE
1.1 This specification2 covers rod and bar of low-carbon nickel-chromium-molybdenum alloys (UNS N10276, N06022, N06035, N06044, N06455, N06058, and N06059), low-carbon nickel-molybdenum-chromium (USN N10362), low-carbon nickel-molybdenum-chromium-tantalum (UNS N06210), low-carbon nickel-chromium-molybdenum-copper alloy (UNS N06200), and low-carbon nickel-chromium-molybdenum-tungsten (UNS N06686) as shown in Table 1, for use in general corrosive service.      
1.2 The following products are covered under this specification:  
1.2.1 Rods and Bars 5/16 in. to 3/4 in. (7.94 mm to 19.05 mm), exclusive, in dimension3, solution annealed and pickled, or mechanically descaled.  
1.2.2 Rods and Bars 3/4 in. to 31/2 in. (19.05 mm to 88.9 mm), inclusive, in dimension3, solution annealed, ground or turned.  
1.2.3 Rods and Bars 1/4 in. to 3 1/2 in. (6.35 mm to 88.9 mm), inclusive, in dimension3, solution annealed, cold worked, ground or turned (N06022, N06059, N06686, and N10276, see Table 2 and Table 3).  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM B446-23(Specification)
Standard Specification for Nickel-Chromium-Molybdenum-Niobium Alloy, Nickel-Chromium-Molybdenum-Silicon Alloy, and Nickel-Chromium-Molybdenum-Tungsten Alloy Rod and Bar

ABSTRACT
This specification covers nickel-chromium-molybdenum-columbium (UNS N06625), nickel-chromium-molybdenum-silicon alloy (UNS N06219), and nickel-chromium-molybdenum-tungsten alloy (UNS N06650) in the form of hot-worked rod and bar and cold-worked rod. The matreial shall conform to the required chemical composition for carbon, manganese, silicon, phosphorus, sulfur, chromium, columbium, tantalum, cobalt, molybdenum, iorn, aluminum, titanium, copper, nickel, tungsten, and nitrogen. The materials shall conform to the the heat treatment and room temperature tensile properties such as tensile strength, yield strength, and elongation. Dimensions of the alloys such as diameter, thickness, or width, length and straightness shall also be determined.
SCOPE
1.1 This specification covers nickel-chromium-molybdenum-niobium alloy (UNS N06625), nickel-chromium-molybdenum-silicon alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650)2 in the form of both hot-worked and cold-worked rod and bar in the conditions shown in Table 1.  
1.1.1 UNS N06625 products are furnished in three grades of different heat-treated conditions:
1.1.1.1 Grade 1 (Annealed)—Material is normally employed in service temperatures up to 1100 °F (593 °C).
1.1.1.2 Grade 2 (Solution Annealed)—Material is normally employed in service temperatures above 1100 °F (593 °C) when resistance to creep and rupture is required.  
Note 1: Hot-working or reannealing may change properties significantly, depending on working history and temperatures.
1.1.1.3 Grade 3 (Solution Annealed and Cold Worked)—Material is normally employed in services where higher strengths are needed.  
1.1.2 Alloys UNS N06219 and UNS N06650 are supplied in solution annealed condition only.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test methods portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM B668-23(Specification)
Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloy Seamless Pipe and Tube

ABSTRACT
This specification covers the standard requirements for UNS N08028 seamless cold-finished or hot-finished pipe and tube intended for general corrosive services. The pipe and tube shall be furnished in the solution-annealed condition and heat treated at a certain range of temperature by subsequent quenching in water or rapidly cooling by other means. Chemical and product analysis shall be conducted on each lot of material as described in a referenced ASTM document and shall conform to the required chemical composition for carbon, silicon, manganese, phosphorus, sulfur, chromium, nickel, molybdenum, copper, and iron. The material shall also be subjected to tension test, flaring test, and hydrostatic or nondestructive test to determine its mechanical properties which shall be in conformity with the tensile strength, yield strength, and elongation requirements.
SCOPE
1.1 This specification covers UNS N08028 and N08029 seamless cold-finished or hot-finished pipe and tube intended for general corrosive service.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B474/B474M-19(2023)(Specification)
Standard Specification for Electric Fusion Welded Nickel and Nickel Alloy Pipe

ABSTRACT
This specification covers electric fusion welded pipe suitable for high-temperature or corrosive service. The pipes are designated into five classes namely Class 1, Class 2, Class 3, Class 4 and Class 5, according to how they are to be welded. The joints shall be full penetration double-welded or single-welded butt joints employing fusion welding processes. The furnished pipe shall undergo heat treatment and a chemical analysis shall be employed for both plate and weld. Each pipe shall be subjected to transverse tension test, transverse guided weld bend test and hydrostatic pressure test.
SCOPE
1.1 This specification covers electric fusion welded pipe suitable for high-temperature or corrosive service as listed in Table 1. (Although no restrictions are placed on the sizes of pipe that may be furnished under this specification, commercial practice is commonly limited to sizes not less than 8 in. [203 mm] nominal diameter.)  
1.2 Five classes of pipe are covered as follows:  
1.2.1 Class 1—Pipe shall be double welded by processes employing filler metal in all passes and shall be completely radiographed.  
1.2.2 Class 2—Pipe shall be double welded by processes employing filler metal in all passes. No radiography is required.  
1.2.3 Class 3—Pipe shall be single welded by processes employing filler metal in all passes and shall be completely radiographed.  
1.2.4 Class 4—Same as Class 3 except that the weld pass exposed to the inside pipe surface may be made without the addition of filler metal.  
1.2.5 Class 5—Pipe shall be double welded by processes employing filler metal in all passes and shall be spot radiographed.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM B167-23(Specification)
Standard Specification for Nickel-Chromium-Aluminum Alloys, Nickel-Chromium-Iron Alloys, Nickel-Chromium-Cobalt-Molybdenum Alloy, Nickel-Iron-Chromium-Tungsten Alloy, and Nickel-Chromium-Molybdenum-Copper Alloy Seamless Pipe and Tube

ABSTRACT
This specification covers nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696) and nickel-chromium-cobalt molybdenum alloy (UNS N06617) in cold-worked annealed, hot-worked annealed, and hot-finished seamless pipe and tube intended for general corrosion resistant and heat resistant applications. The material shall conform to the required chemical composition for nickel, chromium, iron, manganese, molybdenum, cobalt, aluminum, carbon, copper, boron, silicon, sulfur, titanium, niobium, phosphorous, zirconium, yttrium, and cerium. The following test methods shall be performed on the alloys, namely: chemical analysis, tension test, and hydrostatic or nondestructive electric test. The material shall conform to the required mechanical properties such as tensile strength, yield strength, elongation, nondestructive electric test, and rounding method.
SCOPE
1.1 This specification2 covers nickel-chromium-aluminum alloys (UNS N06699), nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696),3 nickel-chromium-cobalt-molybdenum alloy (UNS N06617), nickel-iron-chromium-tungsten alloy (UNS N06674), and nickel-chromium-molybdenum-copper alloy (UNS N06235) in cold-worked annealed, hot-worked annealed, and hot-finished seamless pipe and tube intended for general corrosion resistant and heat resistant applications.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM B444-23(Specification)
Standard Specification for Nickel-Chromium-Molybdenum-Niobium Alloys and Nickel-Chromium-Molybdenum-Silicon Alloy Pipe and Tube

ABSTRACT
This specification covers UNS N06625 and UNS N06852 nickel-chromium-molybdenum-columbium alloys and UNS N06219 nickel-chromium-molybdenum-silicon alloy in the form of cold-worked seamless pipe and tube. UNS N06625 products are furnished in annealed Grade 1 and solution annealed Grade 2 while UNS N06219 and UNS N06852 are in solution annealed condition only. Chemical testing shall be performed on each type of material and shall conform to the chemical composition limits specified for carbon, manganese, silicon, phosphorus, sulfur, chromium, tantalum, columbium, cobalt, molybdenum, iron, aluminum, titanium, copper, and nickel. The material shall undergo tensile testing and shall conform to the required room temperature tensile properties like tensile strength, yield strength, and elongation depending on the heat treatment used and including small diameter and light-walled tubing. Each pipe or tube shall undergo hydrostatic testing and shall conform to the allowable fiber stress and also be examined with a nondestructive electric test as prescribed.
SCOPE
1.1 This specification2 covers nickel-chromium-molybdenum-niobium alloys (UNS N06625 and UNS N06852) and nickel-chromium-molybdenum-silicon alloy (UNS N06219)3 in the form of cold-worked seamless pipe and tube. The general requirements for pipe and tube are covered by Specification B829.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM B805-23(Specification)
Standard Specification for Precipitation Hardening Nickel Alloys Bar and Wire

ABSTRACT
This specification covers UNS N07716, N07725, N07773, N07776, N09777, and N09925 nickel alloy hot or cold finished rounds, squares, hexagons, rectangles, and cold finished wires. Bars should be supplied in solution treated conditions while wires should be in both solution-treated and cold-finished conditions. The recommended solution treatment should consist of heating the material to a certain temperature followed by rapid cooling. Solution-treated materials should at least conform to the minimum room temperature mechanical properties and should be suitable for subsequent age hardening.
SCOPE
1.1 This specification covers nickel alloys UNS N07716, N07725, N07773, N07776, N09777, and N09925 in the form of hot or cold finished rounds, squares, hexagons, rectangles, and cold finished wire.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test methods, portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM B575-17(2023)(Specification)
Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Tungsten, and Low-Carbon Nickel-Molybdenum-Chromium Alloy Plate, Sheet, and Strip

ABSTRACT
This specification covers plate, sheet, and strip of low-carbon nickel-chromium-molybdenum alloys (UNS N10276, N06022, N06455, N06035, UNS N06058, UNS N06059), low carbon nickel-chromium-molybdenum-copper alloy (UNS N06200), low-carbon nickel-chromium-molybdenum-tantalum alloy (UNS N06210), and low-carbon nickel-chromium-molybdenum-tungsten alloy (UNS N06686) for use in general corrosive service. The materials shall conform to the required chemical composition for molybdenum, chromium, iorn, tungsten, cobalt, arbon, silicon, manganese, vanadium, phosphorus, sulfur, titanium, nickel, aluminum, copper, and tantalum. The alloys shall connform to the required tensile properties such as tensile strength, yield strength, elongation, and Rockwell hardness. Sheet and strip shall conform to the required grain sizes. Dimensions such as plate, sheet and strip thickness, width, length, straightness, squareness, flatness and edges shall be determined.
SCOPE
1.1 This specification2 covers plate, sheet, and strip of low-carbon nickel-chromium-molybdenum alloys (UNS N10276, N06022, N06455, N06035, N06044, UNS N06058, UNS N06059),3 low-carbon nickel-chromium-molybdenum-copper alloy (UNS N06200), low-carbon nickel-molybdenum-chromium (UNS N10362), low-carbon nickel-chromium-molybdenum-tantalum alloy (UNS N06210), and low-carbon nickel-chromium-molybdenum-tungsten alloy (UNS N06686) as shown in Table 1, for use in general corrosive service.    
1.2 The following products are covered under this specification:  
1.2.1 Sheet and Strip—Hot or cold rolled, solution annealed, and descaled unless solution anneal is performed in an atmosphere yielding a bright finish.  
1.2.2 Plate—Hot or cold rolled, solution annealed, and descaled.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off