ASTM B1001-17
(Specification)Standard Specification for Copper Electrode Wire Used for Welding Seams of Steel Cans
Standard Specification for Copper Electrode Wire Used for Welding Seams of Steel Cans
ABSTRACT
This specification covers drawn, soft annealed round copper electrode wire used in welding machines for the purpose of seam welding of cans. It does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this specification to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
This specification establishes the requirements with respect to materials and manufacturing process, chemical composition, temper, physical and mechanical properties, workmanship, finish, and appearance. It also provides guidance for sampling, number of tests and retests, specimen preparation, test methods, certification, test report, and packaging and package marking.
SCOPE
1.1 This specification establishes the requirements for drawn, soft annealed round copper electrode wire used in welding machines for the purpose of seam welding of cans.
1.2 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:B1001 −17
Standard Specification for
Copper Electrode Wire Used for Welding Seams of Steel
1
Cans
This standard is issued under the fixed designation B1001; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope F16 Test Methods for Measuring Diameter or Thickness of
Wire and Ribbon for Electronic Devices and Lamps
1.1 This specification establishes the requirements for
4
2.2 NIST Document:
drawn, soft annealed round copper electrode wire used in
NBS Handbook 100 Copper Wire Tables
welding machines for the purpose of seam welding of cans.
1.2 Units—The values stated in SI units are to be regarded
3. General Requirements
as standard. The values given in parentheses are mathematical
3.1 The following sections of Specification B250/B250M,
conversions to inch-pound units that are provided for informa-
as applicable, constitute a part of this specification:
tion only and are not considered standard.
3.1.1 Terminology,
1.3 This standard does not purport to address all of the
3.1.2 Materials and Manufacture,
safety concerns, if any, associated with its use. It is the
3.1.3 Workmanship, Finish, and Appearance,
responsibility of the user of this standard to establish appro-
3.1.4 Sampling,
priate safety and health practices and determine the applica-
3.1.5 Number of Tests and Retests,
bility of regulatory limitations prior to use.
3.1.6 Test Methods,
3.1.7 Significance of Numerical Limits,
2. Referenced Documents
3.1.8 Inspection,
2
2.1 ASTM Standards:
3.1.9 Rejection and Rehearing,
B49 Specification for Copper Rod for Electrical Purposes
3.1.10 Certification,
B193 Test Method for Resistivity of Electrical Conductor
3.1.11 Test Report, and
Materials
3.1.12 Packaging and Package Marking.
B224 Classification of Coppers
4. Ordering Information
B250/B250M Specification for General Requirements for
Wrought Copper Alloy Wire
4.1 Include the following specified choices when placing
B258 Specification for Nominal Diameters and Cross-
orders for product under this specification, as applicable:
SectionalAreasofAWGSizesofSolidRoundWiresUsed
4.1.1 ASTM designation and year of issue,
as Electrical Conductors
4.1.2 Copper [Alloy] UNS No. designation (see Classifica-
E8/E8M Test Methods for Tension Testing of Metallic Ma-
tion B224),
terials
4.1.3 Temper (Temper Section 7),
E53 Test Method for Determination of Copper in Unalloyed
4.1.4 Form (wire) and size (diameter) (Dimensions and
Copper by Gravimetry
Permissible Variations Section 11),
E2575 Test Method for Determination of Oxygen in Copper
4.1.5 How furnished: straight length or coils,
3
and Copper Alloys (Withdrawn 2017)
4.1.6 Quantity; weight for each size and form,
4.1.7 Intended application, and
4.1.8 Package type (stem, reel, bulk or drum).
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
4.1.9 The following options are available but may not be
and CopperAlloys and is the direct responsibility of Subcommittee B05.02 on Rod,
included unless specified at the time of placing the order, when
Bar, Wire, Shapes and Forgings.
Current edition approved Jan. 1, 2017. Published January 2017. DOI: 10.1520/ required:
B1001-17.
4.1.9.1 Heat identification or traceability details,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4.1.9.2 Electromagnetic (eddy current) examination,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3 4
The last approved version of this historical standard is referenced on Available from National Institute of Standards and Technology (NIST), 100
www.astm.org. Bureau Dr., Stop 1070, Gaithersburg, MD 20899-1070, http://www.nist.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B1001−17
4.1.9.3 Certification, and 10.2 The surface of electrode wire shall be free of flaws that
4.1.9.4 Mill Test Report. may interfere with the welding or feeding process.
10.3 The surface of electrode wire shall be free of oils and
5. Materials and Manufacture
other contaminants that may interfere with welding.
5.1 Materials:
5.1.1 The material of manufacture shall be drawn wire of
11. Dimensions, Mass, and Permissible Variations
the designated copper UNS number of such purity to be
11.1 Electrode wire diameter sizes shall be expre
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B1001 − 17
Standard Specification for
Copper Electrode Wire Used for Welding Seams of Steel
1
Cans
This standard is issued under the fixed designation B1001; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope F16 Test Methods for Measuring Diameter or Thickness of
Wire and Ribbon for Electronic Devices and Lamps
1.1 This specification establishes the requirements for
4
2.2 NIST Document:
drawn, soft annealed round copper electrode wire used in
NBS Handbook 100 Copper Wire Tables
welding machines for the purpose of seam welding of cans.
1.2 Units—The values stated in SI units are to be regarded
3. General Requirements
as standard. The values given in parentheses are mathematical
3.1 The following sections of Specification B250/B250M,
conversions to inch-pound units that are provided for informa-
as applicable, constitute a part of this specification:
tion only and are not considered standard.
3.1.1 Terminology,
1.3 This standard does not purport to address all of the
3.1.2 Materials and Manufacture,
safety concerns, if any, associated with its use. It is the
3.1.3 Workmanship, Finish, and Appearance,
responsibility of the user of this standard to establish appro-
3.1.4 Sampling,
priate safety and health practices and determine the applica-
3.1.5 Number of Tests and Retests,
bility of regulatory limitations prior to use.
3.1.6 Test Methods,
3.1.7 Significance of Numerical Limits,
2. Referenced Documents
3.1.8 Inspection,
2
2.1 ASTM Standards:
3.1.9 Rejection and Rehearing,
B49 Specification for Copper Rod for Electrical Purposes
3.1.10 Certification,
B193 Test Method for Resistivity of Electrical Conductor
3.1.11 Test Report, and
Materials
3.1.12 Packaging and Package Marking.
B224 Classification of Coppers
4. Ordering Information
B250/B250M Specification for General Requirements for
Wrought Copper Alloy Wire
4.1 Include the following specified choices when placing
B258 Specification for Nominal Diameters and Cross-
orders for product under this specification, as applicable:
Sectional Areas of AWG Sizes of Solid Round Wires Used
4.1.1 ASTM designation and year of issue,
as Electrical Conductors
4.1.2 Copper [Alloy] UNS No. designation (see Classifica-
E8/E8M Test Methods for Tension Testing of Metallic Ma-
tion B224),
terials
4.1.3 Temper (Temper Section 7),
E53 Test Method for Determination of Copper in Unalloyed
4.1.4 Form (wire) and size (diameter) (Dimensions and
Copper by Gravimetry
Permissible Variations Section 11),
E2575 Test Method for Determination of Oxygen in Copper
4.1.5 How furnished: straight length or coils,
3
and Copper Alloys (Withdrawn 2017)
4.1.6 Quantity; weight for each size and form,
4.1.7 Intended application, and
4.1.8 Package type (stem, reel, bulk or drum).
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper
4.1.9 The following options are available but may not be
and Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod,
included unless specified at the time of placing the order, when
Bar, Wire, Shapes and Forgings.
Current edition approved Jan. 1, 2017. Published January 2017. DOI: 10.1520/ required:
B1001-17.
4.1.9.1 Heat identification or traceability details,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4.1.9.2 Electromagnetic (eddy current) examination,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3 4
The last approved version of this historical standard is referenced on Available from National Institute of Standards and Technology (NIST), 100
www.astm.org. Bureau Dr., Stop 1070, Gaithersburg, MD 20899-1070, http://www.nist.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B1001 − 17
4.1.9.3 Certification, and 10.2 The surface of electrode wire shall be free of flaws that
4.1.9.4 Mill Test Report. may interfere with the welding or feeding process.
10.3 The surface of electrode wire shall be free of oils and
5. Materials and Manufacture
other contaminants that may interfere with welding.
5.1 Materials:
5.1.1 The material of manufacture shall be drawn wire of
11. Dimensions, Mass, and Permissible Variations
the designated copper UNS number of such purity to be
11.1 Electrode wire diameter sizes shall be expressed as the
suitable for use prescribed herein.
nominal diameter of the wire in decimal fractions of a
5.2 Manufa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.