ASTM C478-08

Standard Specification for Precast Reinforced Concrete Manhole Sections

ABSTRACT
This specification covers the manufacture and purchase requirements of products intended for the assembly and construction of circular vertical precast reinforced concrete manholes and structures used in sewer and water works. Reinforced concrete shall consist of cementitious materials, mineral aggregates, and water, in which steel reinforcement has been embedded in such a manner so that the steel reinforcement and concrete act together. The allowable combination of cementitious materials shall be one of the following: Portland cement; Portland blast-furnace slag cement; slag modified Portland cement; Portland pozzolan cement; combination of Portland cement and ground granulated blast-furnace slag which shall conform to the requirements of Grade 100 or 120; combination of Portland cement and fly ash which shall conform to the requirements of Class F or C; or combination of Portland cement, ground granulated blast-furnace slag, and fly ash. Steel reinforcement shall consist of wire, wire fabric, or bars while the secondary synthetic fiber shall be a collated fibrillated polypropylene virgin fiber. Concrete products shall be subjected to steam, water, or sealing membrane curing and shall undergo compression and absorption tests to attain and determine the required compressive strength. The acceptance criteria and design of grade rings, flat slab tops, risers and conical tops, base sections, and steps and ladders shall also be determined.
SCOPE
1.1 This specification covers the manufacture and purchase requirements of products used for the assembly and construction of circular vertical precast reinforced concrete manholes and structures used in sewer and water works.
1.2 Part I, Sections 1-11, of this specification presents general requirements and requirements that are common to each precast concrete product covered by this specification.
1.3 Part II of this specification presents specific requirements for each manhole product in the following sections:
ProductSection Grade Rings12 Flat Slab Tops13 Risers and Conical Tops14 Base Sections15 Steps and Ladders16
Note 1—Future products will to be included in Part II in a future revision of this specification.
1.4 A complete metric companion to this specification has been developed, Specification C 478M; therefore, no metric equivalents are presented in this specification.
Note 2—This specification is a manufacturing and purchase specification only and does not include requirements for backfill, or the relationship between field load conditions and the strength requirements of the manhole products and appurtenances. Experience has shown, however, that the successful performance of this product depends upon the proper selection of the product strength, type of foundation and backfill, and care in the field installation of the manhole products and connecting pipes. The owner of the project for which these products are specified herein is cautioned to require inspection at the construction site.

General Information

• Status: Historical
• Publication Date: 14-Mar-2008
• ICS: 13.060.30 - Sewage water
• Technical Committee: C13 - Concrete Pipe
• Drafting Committee: C13.06 - Manholes and Specials

Relations

• Replaces: ASTM C478-07 - Standard Specification for Precast Reinforced Concrete Manhole Sections
• Effective Date: 15-Mar-2008
• Replaced By: ASTM C478-09 - Standard Specification for Precast Reinforced Concrete Manhole Sections
• Effective Date: 01-Feb-2009
• Referred By: ASTM C858-19 - Standard Specification for Underground Precast Concrete Utility Structures
• Effective Date: 15-Mar-2008
• Referred By: ASTM C1889-21 - Standard Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Utility, Water, and Wastewater Structures Using AASHTO LRFD Design
• Effective Date: 15-Mar-2008
• Referred By: ASTM C857-19 - Standard Practice for Minimum Structural Design Loading for Underground Precast Concrete Utility Structures
• Effective Date: 15-Mar-2008
• Referred By: ASTM C990-09(2019) - Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
• Effective Date: 15-Mar-2008

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C 478 – 08
Standard Specification for
1
Precast Reinforced Concrete Manhole Sections
This standard is issued under the fixed designation C 478; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
PART I—GENERAL 2. Referenced Documents
2
2.1 ASTM Standards:
1. Scope
A 82/A 82M Specification for Steel Wire, Plain, for Con-
1.1 This specification covers the manufacture and purchase
crete Reinforcement
requirements of products used for the assembly and construc-
A 185/A 185M Specification for Steel Welded Wire Rein-
tion of circular vertical precast reinforced concrete manholes
forcement, Plain, for Concrete
and structures used in sewer and water works.
A 496/A 496M Specification for Steel Wire, Deformed, for
1.2 Part I, Sections 1-11, of this specification presents
Concrete Reinforcement
general requirements and requirements that are common to
A 497/A 497M Specification for Steel Welded Wire Rein-
each precast concrete product covered by this specification.
forcement, Deformed, for Concrete
1.3 Part II of this specification presents specific require-
A 615/A 615M Specification for Deformed and Plain
ments for each manhole product in the following sections:
Carbon-Steel Bars for Concrete Reinforcement
Product Section
A 706/A 706M Specification for Low-Alloy Steel De-
Grade Rings 12
formed and Plain Bars for Concrete Reinforcement
Flat Slab Tops 13
Risers and Conical Tops 14 C33 Specification for Concrete Aggregates
Base Sections 15
C 39/C 39M Test Method for Compressive Strength of Cy-
Steps and Ladders 16
lindrical Concrete Specimens
NOTE 1—Future products will to be included in Part II in a future
C 150 Specification for Portland Cement
revision of this specification.
C 260 Specification forAir-EntrainingAdmixtures for Con-
1.4 A complete metric companion to this specification has crete
been developed, Specification C 478M; therefore, no metric C 309 Specification for Liquid Membrane-Forming Com-
equivalents are presented in this specification. pounds for Curing Concrete
C 494/C 494M Specification for Chemical Admixtures for
NOTE 2—This specification is a manufacturing and purchase specifica-
Concrete
tion only and does not include requirements for backfill, or the relation-
C 497 Test Methods for Concrete Pipe, Manhole Sections,
ship between field load conditions and the strength requirements of the
manhole products and appurtenances. Experience has shown, however, or Tile
that the successful performance of this product depends upon the proper
C 595 Specification for Blended Hydraulic Cements
selection of the product strength, type of foundation and backfill, and care
C 618 Specification for Coal Fly Ash and Raw or Calcined
in the field installation of the manhole products and connecting pipes.The
Natural Pozzolan for Use in Concrete
owner of the project for which these products are specified herein is
C 822 Terminology Relating to Concrete Pipe and Related
cautioned to require inspection at the construction site.
Products
C 989 Specification for Ground Granulated Blast-Furnace
1
This specification is under the jurisdiction of ASTM Committee C13 on
2
Concrete Pipe and is the direct responsibility of Subcommittee C13.06 on Manholes For referenced ASTM standards, visit the ASTM website, www.astm.org, or
and Specials. contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Current edition approved March 15, 2008. Published March 2008. Originally Standards volume information, refer to the standard’s Document Summary page on
approved in 1961. Last previous edition approved in 2007 as C 478 – 07. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C478–08
Slag for Use in Concrete and Mortars 4.1.5.3 Chemical admixture for use in producing flowing
C 1017/C 1017M Specification for Chemical Admixtures concrete conforming to Specification C 1017/C 1017M;
for Use in Producing Flowing Concrete 4.1.5.4 Chemical admixture or blend approved by the
3
2.2 ACI Standard: owner.
318 Building Code, Requirements for Reinforced Concrete 4.1.6 Steel Reinforcement—Reinforcement shall consist of
wire conforming to SpecificationA 82/A 82M or Specification
3. Terminology
A 496/A 496M, of wire fabric conforming to Specification
A 185/A 185M or Specification A 497/A 497M, or of bars of
3.1 Definitions—For definitions of terms relating to precast
Grade 40 steel conforming to Specification A 615/A 615M or
reinforced concret
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C478–07 Designation: C 478 – 08
Standard Specification for
1
Precast Reinforced Concrete Manhole Sections
This standard is issued under the fixed designation C 478; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
PART I—GENERAL
1. Scope
1.1 This specification covers the manufacture and purchase requirements of products used for the assembly and construction of
circular vertical precast reinforced concrete manholes and structures used in sewer and water works.
1.2 Part I, Sections 1-11, of this specification presents general requirements and requirements that are common to each precast
concrete product covered by this specification.
1.3 Part II of this specification presents specific requirements for each manhole product in the following sections:
Product Section
Grade Rings 12
Flat Slab Tops 13
Risers and Conical Tops 14
Base Sections 15
Steps and Ladders 16
NOTE 1—Future products will to be included in Part II in a future revision of this specification.
1.4 A complete metric companion to this specification has been developed, Specification C 478M; therefore, no metric
equivalents are presented in this specification.
NOTE 2—This specification is a manufacturing and purchase specification only and does not include requirements for backfill, or the relationship
between field load conditions and the strength requirements of the manhole products and appurtenances. Experience has shown, however, that the
successful performance of this product depends upon the proper selection of the product strength, type of foundation and backfill, and care in the field
installation of the manhole products and connecting pipes. The owner of the project for which these products are specified herein is cautioned to require
inspection at the construction site.
1
ThisspecificationisunderthejurisdictionofASTMCommitteeC13onConcretePipeandisthedirectresponsibilityofSubcommitteeC13.06onManholesandSpecials.
Current edition approved March 1, 2007.15, 2008. Published March 2007.2008. Originally approved in 1961. Last previous edition approved in 20062007as
C478–06b.C 478 – 07.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C478–08
2. Referenced Documents
2
2.1 ASTM Standards:
A 82/A 82M Specification for Steel Wire, Plain, for Concrete Reinforcement
A 185/A 185M Specification for Steel Welded Wire Reinforcement, Plain, for Concrete
A 496/A 496M Specification for Steel Wire, Deformed, for Concrete Reinforcement
A 497/A 497M Specification for Steel Welded Wire Reinforcement, Deformed, for Concrete
A 615/A 615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A 706/A 706M Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement
C 33 Specification for Concrete Aggregates
C 39/C 39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C 150 Specification for Portland Cement
C 260 Specification for Air-Entraining Admixtures for Concrete
C 309 Specification for Liquid Membrane-Forming Compounds for Curing Concrete
C 494/C 494M Specification for Chemical Admixtures for Concrete
C 497 Test Methods for Concrete Pipe, Manhole Sections, or Tile
C 595 Specification for Blended Hydraulic Cements
C 618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C 822 Terminology Relating to Concrete Pipe and Related Products
C 989 Specification for Ground Granulated Blast-Furnace Slag for Use in Concrete and Mortars
C 1017/C 1017M Specification for Chemical Admixtures for Use in Producing Flowing Concrete
3
2.2 ACI Standard:
318 Building Code, Requirements for Reinforced Concrete
3. Terminology
3.1 Definitions— For definitions of terms relating to precast reinforced concrete manholes, see Terminology C 822.
4. Materials and Manufacture
4.1 Generalmaterialrequirementsforprecastreinforcedconcretemanholeproductsarepresentedin4.1.1-4.1.8.Othermaterials
or additional requirements for a product, if any, are covered in the Part II section for that specific product.
4.1.1 Reinforced Concrete—Reinforced concrete shall consist of cementitious materials, mineral aggregates, and water, in
whic
...