ASTM F2194-10
(Specification)Standard Consumer Safety Specification for Bassinets and Cradles
Standard Consumer Safety Specification for Bassinets and Cradles
SCOPE
1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of bassinets and cradles.
1.2 This consumer safety performance specification is intended to minimize the risks of incidents to an infant resulting from normal use and reasonably foreseeable misuse of a bassinet or cradle.
1.3 This consumer safety performance specification covers products intended to provide sleeping accommodations (excluding full-size cribs or swings) for an infant up to approximately 5 months in age. Products used in conjunction with an infant swing are not covered by this specification.
1.4 No bassinet or cradle produced after the approval date of this consumer safety performance specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.5 This consumer safety performance specification is not intended to address incidents and injuries resulting from alteration or unreasonable abuse or misuse of the product by a child or child care giver.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.7 The following precautionary caveat pertains only to the test method portion Section 7 of this consumer safety performance specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2194 – 10
Standard Consumer Safety Specification for
1
Bassinets and Cradles
This standard is issued under the fixed designation F2194; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This consumer safety performance specification addresses infant bassinet and cradle incidents
identified by the U.S. Consumer Product Safety Commission (CPSC).
In response to the incident data compiled by the CPSC, this consumer safety performance
specificationattemptstominimizethefollowinghazards:(1)suffocation,(2)tipover,(3)collapse,and
(4)hooddetachment.Italsoaddressescornerpostextensions,whichmaycatchpacifiercords,ribbons,
necklaces, or clothing which a child may be wearing and which may be caught on a projection. This
specification does not cover products that are blatantly misused or used in a careless manner that
disregards the safety instructions and warnings provided with each bassinet or cradle.
1. Scope mance specification. This standard does not purport to address
all of the safety concerns, if any, associated with its use. It is
1.1 This consumer safety specification covers performance
the responsibility of the user of this standard to establish
requirements, test methods, and marking requirements to
appropriate safety and health practices and determine the
promote safe use of bassinets and cradles.
applicability of regulatory requirements prior to use.
1.2 This consumer safety performance specification is in-
tended to minimize the risks of incidents to an infant resulting
2. Referenced Documents
from normal use and reasonably foreseeable misuse of a
2
2.1 ASTM Standards:
bassinet or cradle.
D3359 Test Methods for Measuring Adhesion by Tape Test
1.3 This consumer safety performance specification covers
F406 Consumer Safety Specification for Non-Full-Size
products intended to provide sleeping accommodations (ex-
Baby Cribs/Play Yards
cluding full-size cribs or swings) for an infant up to approxi-
F963 Consumer Safety Specification for Toy Safety
mately 5 months in age. Products used in conjunction with an
3
2.2 Federal Regulations:
infant swing are not covered by this specification.
16 CFR 1303 Ban of Lead-Containing Paint and Certain
1.4 Nobassinetorcradleproducedaftertheapprovaldateof
Consumer Products Bearing Lead-Containing Paint
this consumer safety performance specification shall, either by
16 CFR 1500 Hazardous Substances Act Regulations In-
label or other means, indicate compliance with this specifica-
cluding Sections
tion unless it conforms to all requirements contained herein.
16 CFR 1500.48 Technical Requirements for Determining a
1.5 This consumer safety performance specification is not
Sharp Point in Toys and Other Articles for Use by
intended to address incidents and injuries resulting from
Children Under Eight Years of Age
alteration or unreasonable abuse or misuse of the product by a
16 CFR 1500.49 Technical Requirements for Determining a
child or child care giver.
Sharp Metal or Glass Edge in Toys or Other Articles
1.6 The values stated in inch-pound units are to be regarded
Intended for Use by Children Under Eight Years of Age
as standard. The values given in parentheses are mathematical
16 CFR 1501 Method for Identifying Toys and Other
conversions to SI units that are provided for information only
Articles Intended for Use by Children Under Three Years
and are not considered standard.
of Age Which Present Choking, Aspiration, or Ingestion
1.7 The following precautionary caveat pertains only to the
Hazards Because of Small Parts
test method portion Section 7 of this consumer safety perfor-
1 2
This specification is under the jurisdiction of ASTM Committee F15 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Consumer Products and is the direct responsibility of Subcommittee F15.18 on contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Cribs, Toddler Beds, Play Yards, Bassinets, Cradles and Changing Tables. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved April 1, 2010. Published April 2010. Originally the ASTM website.
´1 3
approved in 2002. Last previous edition approved in 2007 as F2194 – 07a . DOI: AvailablefromU.S.GovernmentPrintingOfficeSuperintendentofDocuments,
10.1520/F2194-10. 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F2194 – 10
3.1.4 fabric, n—any woven, knit, coated, lami
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation:F2194–07a Designation: F2194 – 10
Standard Consumer Safety Specification for
1
Bassinets and Cradles
This standard is issued under the fixed designation F2194; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
´ NOTE—Paragraph 9.1.2 was corrected editorially in December 2007.
INTRODUCTION
This consumer safety performance specification addresses infant bassinet and cradle incidents
identified by the U.S. Consumer Product Safety Commission (CPSC).
In response to the incident data compiled by the CPSC, this consumer safety performance
specificationattemptstominimizethefollowinghazards:(1)suffocation,(2)tipover,(3)collapse,and
(4)hooddetachment.Italsoaddressescornerpostextensions,whichmaycatchpacifiercords,ribbons,
necklaces, or clothing which a child may be wearing and which may be caught on a projection. This
specification does not cover products that are blatantly misused or used in a careless manner that
disregards the safety instructions and warnings provided with each bassinet or cradle.
1. Scope
1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote
safe use of bassinets and cradles.
1.2 This consumer safety performance specification is intended to minimize the risks of incidents to an infant resulting from
normal use and reasonably foreseeable misuse of a bassinet or cradle.
1.3 This consumer safety performance specification covers products intended to provide sleeping accommodations (excluding
full-size cribs or swings) for an infant up to approximately 5 months in age. Products used in conjunction with an infant swing
are not covered by this specification.
1.4 No bassinet or cradle produced after the approval date of this consumer safety performance specification shall, either by
label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.5 This consumer safety performance specification is not intended to address incidents and injuries resulting from alteration
or unreasonable abuse or misuse of the product by a child or child care giver.
1.6
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.7 The following precautionary caveat pertains only to the test method portion Section 7 of this consumer safety performance
specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of
regulatory requirements prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D3359 Test Methods for Measuring Adhesion by Tape Test
F406 Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards
F963 Consumer Safety Specification for Toy Safety
1
This specification is under the jurisdiction of ASTM Committee F15 on Consumer Products and is the direct responsibility of Subcommittee F15.18 on Cribs, Toddler
Beds, Play Yards, Bassinets, Cradles and Changing Tables.
Current edition approved Oct. 1, 2007. Published November 2007. Originally approved in 2002. Last previous edition approved in 2007 as F2194–07. DOI:
10.1520/F2194-07AE01.
´1
Current edition approved April 1, 2010. Published April 2010. Originally approved in 2002. Last previous edition approved in 2007 as F2194 – 07a . DOI:
10.1520/F2194-10.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F2194 – 10
FIG. 1 CAMI Infant Dummy, Mark II 17.5 lb (7.9 kg)
3
2.2 Federal Regulations:
16 CFR 1303 Ban of Lead-Containing Paint and Certain Consumer Products Bearing Lead-Containing Paint
16 CFR 1500 Hazardous Substances Act Regulations Including Sections
16 CFR 1500.48 Technical Requirements for Determining a Sharp Point in Toys a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.