iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F718-07

(Specification)

Standard for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet

Standard for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet

ABSTRACT
The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet2 provides on one sheet needed information concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation requirements, application requirements, and safety. When filling out the Product/Procedure Data Sheet remember that the information contained therein will be utilized by both technical and production personnel. The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material, by production personnel to evaluate production compatibility of proposed materials and to provide application instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.
SCOPE
1.1 The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet provides on one sheet needed information concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation requirements, application requirements, and safety. The front side of the sheet contains four major, numbered paragraphs and a highlighted section for Special Safety Precautions. These paragraphs are as follows:
I. Generic Type and Description
II. Manufacturers Data
III. Properties
IV. Surface Preparation Minimum Requirements
The back side of the page contains the following paragraphs:
V. Mixing Procedure
VI. Application
1.2 The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material, by production personnel to evaluate production compatibility of proposed materials and to provide application instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.

General Information

Status
Historical
Publication Date
28-Feb-2007
ICS
47.020.05 - Materials and components for shipbuilding
Technical Committee
F25 - Ships and Marine Technology
Drafting Committee
F25.01 - Structures
Current Stage
Ref Project

Relations

Replaces
ASTM F718-99(2005)e1 - Standard for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet
Effective Date
01-Mar-2007
Replaced By
ASTM F718-07(2011)e1 - Standard Specification for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet
Effective Date
01-Mar-2007
Referred By
ASTM F941-99(2019) - Standard Practice for Inspection of Marine Surface Preparation and Coating Application
Effective Date
01-Mar-2007

Buy Standard

ASTM F718-07 - Standard for Shipbuilders and Marine Paints and Coatings Product/Procedure Data SheetASTM F718-07 - Standard for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet
PreviousNext
Technical specification
ASTM F718-07 - Standard for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F718 – 07
Standard Specification for
Shipbuilders and Marine Paints and Coatings Product/
1
Procedure Data Sheet
ThisstandardisissuedunderthefixeddesignationF718;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope D1475 Test Method For Density of Liquid Coatings, Inks,
and Related Products
1.1 The Shipbuilders and Marine Paints and Coatings
2
D1640 Test Methods for Drying, Curing, or Film Formation
Product/Procedure Data Sheet provides on one sheet needed
of Organic Coatings at Room Temperature
information concerning the characteristics of a specific paint or
D1650 Test Methods of Sampling and Testing Shellac
coating to include generic description, physical properties,
4
Varnish
surface preparation requirements, application requirements,
D2697 TestMethodforVolumeNonvolatileMatterinClear
and safety. The front side of the sheet contains four major,
or Pigmented Coatings
numbered paragraphs and a highlighted section for Special
D3278 Test Methods for Flash Point of Liquids by Small
Safety Precautions. These paragraphs are as follows:
Scale Closed-Cup Apparatus
I. Generic Type and Description
2.2 ASTM Adjunct:
II. Manufacturers Data
Shipbuilder’s and Marine Paints and Coatings Product/
III. Properties
2
Procedure Data Sheets
IV. Surface Preparation Minimum Requirements
5
2.3 U.S. EPA Method:
The back side of the page contains the following paragraphs:
24 U.S. Environmental Protection Agency, 40 CFR Ch. 1,
V. Mixing Procedure
Part 60, Appendix A, Determination of Volatile Matter
VI. Application.
Content, Density, Volume Solids, and Weight Solids of
1.2 The completed data sheets can be used by technical
Surface Coatings
personnel to help evaluate the technical acceptability of a
proposed material, by production personnel to evaluate pro-
3. Instructions for Completing Data Sheet
duction compatibility of proposed materials and to provide
3.1 When filling out the Product/Procedure Data Sheet (see
application instructions for selected paints and coatings mate-
Figs. 1 and 2) remember that the information contained therein
rials, and by quality control personnel to verify attributes of
will be utilized by both technical and production personnel.
materials.
Keep it simple and brief but complete. The following instruc-
2. Referenced Documents tions are organized by paragraph numbers contained within the
3 data sheet.
2.1 ASTM Standards:
3.2 Paragraph I—Generic Type and Description—Use only
D56 Test Method for Flash Point by Tag Closed Cup Tester
known and industry-accepted generic descriptions. Also, list
D93 Test Methods for Flash Point by Pensky-Martens
anyspecificationspecificterminology(forexample,MIL-PRF-
Closed Cup Tester
23236 Type I, Class 2, etc.) See Fig. 1.
D523 Test Method for Specular Gloss
3.3 Paragraph II—Manufacturers Data—This section is
self-explanatory with the possible exception of subparagraph
(f).This can be as complete or as brief as the concerned parties
1
This standard is under the jurisdiction of ASTM Committee F25 on Ships and
desire. For example, a separate attached list of compatible and
Marine Technology and is the direct responsibility of Subcommittee F25.01 on
incompatible topcoats or acceptable cargo exposures could be
Structures.
included. See Fig. 1.
Current edition approved March 1, 2007. Published May 2007. Originally
´1
approved in 1981. Last previous edition approved in 2005 as F718 – 99 (2005) .
3.4 Paragraph III—Properties—This section is also self-
DOI: 10.1520/F0718-07.
explanatory with the following exceptions:
2
Available from ASTM International Headquarters. Order Adjunct No.
ADJF0718. Original adjunct produced in 1993.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Withdrawn.
5
Standards volume information, refer to the standard’s Document Summary page on AvailablefromU.S.GovernmentPrintingOfficeSuperintendentofDocuments,
the ASTM website. 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F718 – 07
FIG. 1 Data Sheet (Front)
2

---------------------- Page: 2 ----------------------
F718 – 07
FIG. 2 Data Sheet (Back)
3

---------------------- Page: 3 ----------------------
F718 – 07
3.4.1 Subparagraph (a)—If agreed upon by the concerned 3.8 Paragraph V—Mixing Proce
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F1298-90(2023)(Specification)
Standard Specification for Flexible, Expansion-Type Ball Joints for Marine Applications

ABSTRACT
This specification covers the design, manufacture, and testing of ball joints utilized for accommodating thermal expansion and contraction, or mechanical movement of a pipeline carrying fluid. Ball joints shall be designed to conform to the requirements prescribed. Flex cycle test, thermal cycling test, and hydrostatic test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers the design, manufacture, and testing of ball joints utilized for accommodating thermal expansion and contraction, or mechanical movement of a pipeline carrying fluid. The ball joints are intended for use in systems operating above 0 °F (18 °C).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F992-17(2022)(Specification)
Standard Specification for Valve Label Plates

ABSTRACT
This specification covers the materials, dimensions, inscription, and methods of inscribing for shipboard valve label plates. Label plates shall be classified by type, grade, class, size, and letter size in accordance with material and method of inscribing, method of attachment, thickness of sheet, strip, or plate, dimensions, and letter size to be used. Types and materials: type I - anodized aluminium, engraved; type II - anodized aluminium, metal photo; type III - stainless steel, engraved; type IV - brass, engraved; and type V - plastic, engraved. Grades and methods of attachment: grade A - adhesive on metal bracket (backling plate); grade B - metal strapping or screw; grade C - welding; grade D - secured by handwheel nut; and grade E - connection to valve stem, bonnet, or flange. Inscription on label plates shall include the system identification number, valve identification number, and the function of the valve. The pressure in line, where the line is coming from or going to, or both, may be included along with any other pertinent information.
SCOPE
1.1 This specification covers the materials, dimensions, inscription, and methods of inscribing for shipboard valve label plates.  
1.2 Fasteners shall be ordered separately and are not included in this specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F718-22(Specification)
Standard Specification for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet

ABSTRACT
The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet2 provides on one sheet needed information concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation requirements, application requirements, and safety. When filling out the Product/Procedure Data Sheet remember that the information contained therein will be utilized by both technical and production personnel. The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material, by production personnel to evaluate production compatibility of proposed materials and to provide application instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.
SCOPE
1.1 The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet2 provides on one sheet needed information concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation requirements, application requirements, and safety. The front side of the sheet contains four major, numbered paragraphs and a highlighted section for Special Safety Precautions. These paragraphs are as follows:
I. Generic Type and Description
II. Manufacturers Data
III. Properties  
IV. Surface Preparation Minimum Requirements  
The back side of the page contains the following paragraphs:
V. Mixing Procedure
VI. Application  
1.2 The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material, by production personnel to evaluate production compatibility of proposed materials and to provide application instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1138-21(Specification)
Standard Specification for Spray Shields for Mechanical Joints

ABSTRACT
This specification describes the manufacturing requirements for spray shield stock and the fabrication and installation requirements for spray shields made from that stock. The physical and mechanical properties for the aluminized glass cloth, thread, and protective outer jacket shall be as specified. If lacing hooks or rings are of the type that fastens by stitching, the hooks or rings shall be attached to the backup washers using a wire stitch machine and wire. The methods for testing the aluminized glass cloth, thread, and protective outer jacket shall be as specified.
SCOPE
1.1 This specification describes the manufacturing requirements for spray shield stock and the fabrication and installation requirements for spray shields made from that stock.  
1.1.1 Sections 2 – 14 address the manufacturing requirements for the spray shield stock. Annex A1 addresses the fabrication and installation requirements for the spray shields.  
1.1.2 Fig. 1 shows the typical construction of a spray shield. Figs. 2-6 show methods of installation of a spray shield on various mechanical joints.
FIG. 1 Spray Shield Construction (Typical)  
FIG. 2 Installation of Butterfly Valve Shield  
FIG. 3 Spray Shield for Pump Inlet Head  
FIG. 4 Spray Shield for Simplex Strainer  
FIG. 5 Spray Shield for Butterfly Valve  
FIG. 6 Spray Shield for Valve Bonnet  
1.2 The shields are intended for use around mechanical joints (flanged, bolted unions, and so forth) in liquid piping systems with an internal pressure exceeding 26.1 psi (0.18 N/mm2) to prevent the impingement of flammable liquid on hot surfaces or fluids onto electrical switchboards and components resulting from a leak in the mechanical joint, unless otherwise invoked by contractual requirements. Spray Shields are excluded on all suction lines with a head pressure less than 26.1 psi (0.18 N/mm2) and mechanical joints in non-flammable liquid systems in excess of 10 ft of an electrical switchboard, unless otherwise invoked by contractual requirements.2  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM F941-99(2019)(Practice)
Standard Practice for Inspection of Marine Surface Preparation and Coating Application

SIGNIFICANCE AND USE
3.1 This practice may be invoked by any of the parties mentioned in 1.2 and may be included as part of a specification or used to clarify or reinforce an existing specification that does not adequately address inspection. When invoked by the ship owner on the shipbuilder, the shipbuilder is responsible for the coordination effort.  
3.2 As surface preparation and coating requirements generally differ from ship area to ship area, this practice shall be applied separately to those areas of similar requirements.  
3.3 The contents of this practice shall be addressed (for each applicable ship area) at a prestartup meeting attended by the parties mentioned in 1.2.
SCOPE
1.1 This practice is intended to serve as a guide for determining specific inspection requirements for marine surface preparation and coating application during new construction, major retrofit, or routine maintenance contracts.  
1.2 It is intended that this practice be used to coordinate inspection activities between ship owner, ship builder, coatings manufacturer and coatings applicator, and that specific requirements be developed before the commencement of surface preparation or coating application, or both.  
1.3 This practice does not provide a means of recording required data (for example, film thicknesses, temperatures, relative humidity, and so forth), but instead establishes a format for deciding what data must be recorded, when during the preparation/coating process, and by whom.  
1.4 This practice does not establish accept/reject criteria for surface preparation or coating inspection, nor does it address methods of repairing deficiencies found. It does, however, provide a means of determining them.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F940-99(2019)e1(Practice)
Standard Practice for Quality Control Receipt Inspection Procedures for Protective Coatings (Paint), Used in Marine Construction and Shipbuilding

SIGNIFICANCE AND USE
5.1 This practice provides a means of assuring that products supplied during ship construction and maintenance are substantially the same as the materials on which the original selection was based. The selection of a paint for shipboard use frequently involves laboratory and field evaluations of candidate materials as part of the specification process. When a paint is selected, it shall have the same composition and characteristics throughout the delivery period as the materials originally evaluated.  
5.1.1 When significant changes in composition or paint characteristics are observed, it is necessary to determine the cause of the change (production error or formulation change) and its impact on coating performance. Actions to take if a formulation change is required are specified in 6.5.  
5.2 This practice is not meant to cover all possible chemical or physical tests that may be used to identify a coating. Additional tests may be needed to meet specific user needs.  
5.3 This practice does not recommend specific tolerance limits for the tests indicated. Tolerance values need to be agreed upon by the coating supplier, the shipbuilder, and the ship’s owner.  
5.4 This practice does not establish critical attributes that must be controlled. These attributes are selected by the shipbuilder and the ship’s owner based on specific needs (for example, colors).
SCOPE
1.1 This practice provides the quality control receipt inspection procedures for protective coatings (paints) procured for end item use on ships and other marine structures. The practice includes methods and procedures for verifying that coating materials received are within the range of physical and chemical characteristics as those originally specified and tested.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1267-18(2023)(Specification)
Standard Specification for Metal, Expanded, Steel

ABSTRACT
This specification covers expanded metal. Expanded metal shall be of the following types, classes, grades such as type I-expanded, type II-expanded and flattened, class I-uncoated, class2-hot-dip zinc uncoated, class 3-corrosion resisting steel, grade A and grade B. Expanded metal shall be made from commercial steel, carbon steel sheets or from stainless steel sheets. Expanded metal shall be manufactured with the corresponding thickness, design size, opening size and strand size. Each single strand test specimen shall be visually inspected, and that surface of the strand observed to have the most nearly uniform coating shall be the tension surface when the strand is subject to bending. The coating thickness shall be measured microscopically at a suitable magnification. The minimum and maximum coating thicknesses shall be measured on each of the four exposed surfaces, but not at the corners.
SCOPE
1.1 This specification covers expanded metal.  
1.1.1 Expanded metal covered by this specification is intended for a variety of applications.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only and may be approximate.  
1.3 The following precautionary caveat pertains only to the test methods portion, Section 11, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM F1298-90(2023)(Specification)
Standard Specification for Flexible, Expansion-Type Ball Joints for Marine Applications

ABSTRACT
This specification covers the design, manufacture, and testing of ball joints utilized for accommodating thermal expansion and contraction, or mechanical movement of a pipeline carrying fluid. Ball joints shall be designed to conform to the requirements prescribed. Flex cycle test, thermal cycling test, and hydrostatic test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers the design, manufacture, and testing of ball joints utilized for accommodating thermal expansion and contraction, or mechanical movement of a pipeline carrying fluid. The ball joints are intended for use in systems operating above 0 °F (18 °C).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM E1123-86(2023)(Practice)
Standard Practices for Mounting Test Specimens for Sound Transmission Loss Testing of Naval and Marine Ship Bulkhead Treatment Materials

SIGNIFICANCE AND USE
3.1 The sound transmission loss provided by a material that covers a flat surface depends not only on the physical properties of the material but also on the type of structure to which it is mounted and the mounting method used.  
3.2 Naval and marine architects and design engineers require specific transmission loss characteristics of acoustical treatment materials as they would exhibit installed on a ship's structure. The mounting structure and procedures specified in these practices are intended to simulate such a shipboard environment.  
3.3 Test reports may refer to this mounting by Practices E1123 instead of providing a detailed description of the mounting used.
SCOPE
1.1 These practices describe test specimen mountings to be used for naval and marine ship applications during sound transmission loss tests performed in accordance with Test Method E90.  
1.2 The structure specified in these practices is intended for mounting of single-layer treatments or composite treatments consisting of various materials and configurations. Acoustical treatment materials may be combinations of acoustical absorbent materials, limp mass septums, and insulation materials.  
1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F718-22(Specification)
Standard Specification for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet

ABSTRACT
The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet2 provides on one sheet needed information concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation requirements, application requirements, and safety. When filling out the Product/Procedure Data Sheet remember that the information contained therein will be utilized by both technical and production personnel. The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material, by production personnel to evaluate production compatibility of proposed materials and to provide application instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.
SCOPE
1.1 The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet2 provides on one sheet needed information concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation requirements, application requirements, and safety. The front side of the sheet contains four major, numbered paragraphs and a highlighted section for Special Safety Precautions. These paragraphs are as follows:
I. Generic Type and Description
II. Manufacturers Data
III. Properties  
IV. Surface Preparation Minimum Requirements  
The back side of the page contains the following paragraphs:
V. Mixing Procedure
VI. Application  
1.2 The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material, by production personnel to evaluate production compatibility of proposed materials and to provide application instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off