ASTM D2058-03(2022)
(Test Method)Standard Test Method for Durability of Finish of Zippers to Drycleaning
Standard Test Method for Durability of Finish of Zippers to Drycleaning
SIGNIFICANCE AND USE
5.1 Test Method D2058 is useful for determining the effect of repeated drycleaning on the appearance of the decorative coating of a zipper.
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.
5.3 The method(s) in the standard along with those in Test Methods D2051, D2052, D2053, D2054, D2057, D2059, D2060, D2061, and D2062 are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and thoroug...
SCOPE
1.1 This test method covers the determination of the durability of the enamel or other decorative coating of zippers when subjected to drycleaning.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D2058 − 03 (Reapproved 2022)
Standard Test Method for
Durability of Finish of Zippers to Drycleaning
This standard is issued under the fixed designation D2058; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D2062 Test Methods for Operability of Zippers
2.2 AATCC Method:
1.1 This test method covers the determination of the dura-
Method 86 Drycleaning: Durability of Applied Designs and
bilityoftheenamelorotherdecorativecoatingofzipperswhen
Finishes
subjected to drycleaning.
1.2 This standard does not purport to address all of the
3. Terminology
safety concerns, if any, associated with its use. It is the
3.1 Definitions:
responsibility of the user of this standard to establish appro-
3.1.1 For definitions of zipper terms used in this standard,
priate safety, health, and environmental practices and deter-
refer to Terminology D2050. For definitions of other textile
mine the applicability of regulatory limitations prior to use.
terminology used in this standard refer to Terminology D123.
1.3 This international standard was developed in accor-
dance with internationally recognized principles on standard-
4. Summary of Test Method
ization established in the Decision on Principles for the
4.1 A specimen is agitated in a solution of solvent and a
Development of International Standards, Guides and Recom-
drycleaning detergent with steel balls to simulate the action
mendations issued by the World Trade Organization Technical
that occurs in a drycleaning machine.
Barriers to Trade (TBT) Committee.
5. Significance and Use
2. Referenced Documents
2 5.1 Test Method D2058 is useful for determining the effect
2.1 ASTM Standards:
of repeated drycleaning on the appearance of the decorative
D123 Terminology Relating to Textiles
coating of a zipper.
D2050 Terminology Relating to Subassemblies Used in the
5.2 This test method is considered satisfactory for accep-
Manufacture of Textiles
D2051 Test Method for Durability of Finish of Zippers to tance testing of commercial shipments because the method has
been used extensively in the trade for acceptance testing.
Laundering
D2052 Test Method for Colorfastness of Zippers to Dry- 5.2.1 If there are differences of practical significance be-
tween reported test results for two laboratories (or more),
cleaning
D2053 Test Method for Colorfastness of Zippers to Light comparative tests should be performed to determine if there is
a statistical bias between them, using competent statistical
D2054 Test Method for Colorfastness of Zipper Tapes to
Crocking assistance.As a minimum, the test samples should be used that
are as homogeneous as possible, that are drawn from the
D2057 Test Method for Colorfastness of Zippers to Laun-
dering material from which the disparate test results were obtained,
and that are randomly assigned in equal numbers to each
D2059 Test Method for Resistance of Zippers to Salt Spray
(Fog) laboratory for testing. Other materials with established test
values may be used for this purpose. The test results from the
D2060 Test Methods for Measuring Zipper Dimensions
D2061 Test Methods for Strength Tests for Zippers two laboratories should be compared using a statistical test
unpaired data, at a probability level chosen prior to the testing
series. If a bias is found, either its cause must be found and
This test method is under the jurisdiction ofASTM Committee D13 on Textiles
corrected, or future test results must be adjusted in consider-
and is the direct responsibility of Subcommittee D13.54 on Subassemblies. The
ation of the known bias.
method was developed in cooperation with the Slide Fastener Assn. Inc.
Current edition approved March 1, 2022. Published March 2022. Originally
5.3 The method(s) in the standard along with those in Test
approved in 1961. Last previous edition approved in 2014 as D2058 – 03(2014).
Methods D2051, D2052, D2053, D2054, D2057, D2059,
DOI: 10.1520/D2058-03R22.
For referenced ASTM standards, visit the ASTM web site, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on Technical Manual of the American Association of Textile Chemists and
the ASTM web site. Colorists, P.O. Box 12215, Research Triangle Park, NC 27709.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.