ASTM D5213-19
(Specification)Standard Specification for Polymeric Resin Film for Electrical Insulation and Dielectric Applications
Standard Specification for Polymeric Resin Film for Electrical Insulation and Dielectric Applications
ABSTRACT
This specification establishes the requirements for the material, dimensions and tolerances, and property values of polymeric resin films, in sheet or strip form, for use in electrical insulation and dielectric applications. Type I are flexible unsupported films for general purpose, while Type II are heat-sealable coated on one (Grade 1) or both (Grade 2) sides. Materials covered here are (A) poly(N,N'-p,p'-oxydiphenylene pyromellitimide), (B) poly(N,N'-p,p'-oxydiphenylene biphenyltetracarboxylimide, (C) poly(N,N'-p-phenylene biphenyltetracarboxylimide), (D) FEP-fluorocarbon, (E) polyethylene terephthalate, (F) polyethylene naphthalate, and (G) polyetherimide. Individual materials class of films shall be tested and conform accordingly the following property values: tensile strength; elongation; shrinkage; moisture absorption; dielectric strength; volume resistivity; permittivity; and dissipation factor.
SCOPE
1.1 This specification covers requirements for the material, dimensions and tolerances, and property values of film, in sheet or strip form, with or without heat-sealable coatings.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
Note 1: This document is similar to IEC 60674, Part 3, Sheets 2, 4, 5, 6, and 7.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D5213 −19
Standard Specification for
Polymeric Resin Film for Electrical Insulation and Dielectric
1
Applications
This standard is issued under the fixed designation D5213; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 2.2 IEC Standards:
Publication 60674-3 Specification for Electrical Films for
1.1 This specification covers requirements for the material,
4
Electrical Purposes
dimensionsandtolerances,andpropertyvaluesoffilm,insheet
or strip form, with or without heat-sealable coatings.
3. Terminology
1.2 The values stated in SI units are to be regarded as the
3.1 Definitions—Definitions are in accordance with Termi-
standard. The values given in parentheses are for information
nologies D1711 and D883 unless otherwise specified.
only.
4. Classification
NOTE 1—This document is similar to IEC 60674, Part 3, Sheets 2, 4, 5,
4.1 This specification covers the following:
6, and 7.
4.1.1 Type I—General purpose,
1.3 This international standard was developed in accor-
4.1.2 Type II—Heat sealable,
dance with internationally recognized principles on standard-
4.1.2.1 Grade 1—One side coated, and
ization established in the Decision on Principles for the
4.1.2.2 Grade 2—Two sides coated.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
4.2 Materials:
Barriers to Trade (TBT) Committee.
4.2.1 Item A—Poly(N,N'-p,p'-oxydiphenylene
pyromellitimide),
2. Referenced Documents
4.2.2 Item B—Poly(N,N'-p,p'-oxydiphenylene
2
biphenyltetracarboxylimide,
2.1 ASTM Standards:
4.2.3 Item C—Poly(N,N'-p-phenylene
D149 Test Method for Dielectric Breakdown Voltage and
biphenyltetracarboxylimide),
DielectricStrengthofSolidElectricalInsulatingMaterials
4.2.4 Item D—FEP-fluorocarbon, and
at Commercial Power Frequencies
4.2.5 Item E—Polyethylene terephthalate.
D883 Terminology Relating to Plastics
4.2.6 Item F—Polyethylene naphthalate.
D1711 Terminology Relating to Electrical Insulation
4.2.7 Item G—Polyetherimide.
D2305 Test Methods for Polymeric Films Used for Electri-
cal Insulation
4.3 For the purposes of this specification, a sheet refers to
D3636 Practice for Sampling and Judging Quality of Solid
material greater than 75 mm in width and a strip refers to
Electrical Insulating Materials
material 75mm or less in width.
D4088 Practice for Preparation for Shipment of Solid Elec-
3
5. Ordering Information
trical Insulating Materials (Withdrawn 2003)
5.1 Order the film covered by this specification stating the
type, grade, class, thickness, width, and roll dimensions.
1
This specification is under the jurisdiction of ASTM Committee D09 on
Electrical and Electronic Insulating Materials and is the direct responsibility of
6. Materials
Subcommittee D09.07 on Electrical Insulating Materials.
Current edition approved March 1, 2019. Published March 2019. Orginally
6.1 Type I material is flexible, unsupported film.
approved in 1991. Last previous edition approved in 2012 as D5213 – 12. DOI:
6.2 Type II material is film meeting all of the requirements
10.1520/D5213-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
of Type I, and having a heat-sealable coating on one or both
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
sides.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3
4
The last approved version of this historical standard is referenced on Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
www.astm.org. 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5213−19
7. Requirements that might affect either appearance or serviceability. The
heat-sealable coating for Type II material shall be uniform in
7.1 The film covered by this specification shall meet the
appearance.
property requirements given in Tables 1-7 and Table 8 when
tested by the methods given in Test Methods D2305.
8. Sampling
7.1.1 Type II films, prior to coating, shall meet all of the
8.1 Sample in accordance with Practice D3636, unless
requirementsgiveninTable1forfilmsofthethicknessesgiven
otherwise
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D5213 − 12 D5213 − 19
Standard Specification for
Polymeric Resin Film for Electrical Insulation and Dielectric
1
Applications
This standard is issued under the fixed designation D5213; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers requirements for the material, dimensions and tolerances, and property values of film, in sheet or
strip form, with or without heat-sealable coatings.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
NOTE 1—This document is similar to IEC 60674, Part 3, Sheets 2, 4, 5, 6, and 7.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at
Commercial Power Frequencies
D883 Terminology Relating to Plastics
D1711 Terminology Relating to Electrical Insulation
D2305 Test Methods for Polymeric Films Used for Electrical Insulation
D3636 Practice for Sampling and Judging Quality of Solid Electrical Insulating Materials
3
D4088 Practice for Preparation for Shipment of Solid Electrical Insulating Materials (Withdrawn 2003)
2.2 IEC Standards:
4
Publication 60674-3 Specification for Electrical Films for Electrical Purposes
3. Terminology
3.1 Definitions—Definitions are in accordance with Terminologies D1711 and D883 unless otherwise specified.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 sheet, n—material greater than 75 mm in width.
3.2.2 strip, n—material 75 mm or less in width.
4. Classification
4.1 This specification covers the following:
4.1.1 Type I—General purpose,
4.1.2 Type II—Heat sealable,
4.1.2.1 Grade 1—One side coated, and
1
This specification is under the jurisdiction of ASTM Committee D09 on Electrical and Electronic Insulating Materials and is the direct responsibility of Subcommittee
D09.07 on Flexible and Rigid Electrical Insulating Materials.
Current edition approved Nov. 1, 2012March 1, 2019. Published November 2012March 2019. Orginally approved in 1991. Last previous edition approved in 20072012
as D5213 – 07.D5213 – 12. DOI: 10.1520/D5213-12.10.1520/D5213-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
4
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5213 − 19
4.1.2.2 Grade 2—Two sides coated.
4.2 Materials:
4.2.1 Item A—Poly(N,N'-p,p'-oxydiphenylene pyromellitimide),
4.2.2 Item B—Poly(N,N'-p,p'-oxydiphenylene biphenyltetracarboxylimide,
4.2.3 Item C—Poly(N,N'-p-phenylene biphenyltetracarboxylimide),
4.2.4 Item D—FEP-fluorocarbon, and
4.2.5 Item E—Polyethylene terephthalate.
4.2.6 Item F—Polyethylene naphthalate.
4.2.7 Item G—Polyetherimide.
4.3 For the purposes of this specification, a sheet refers to material greater than 75 mm in width and a strip refers to material
75mm or less in width.
5. Ordering Information
5.1 Order the film covered by this specification stating the type, grade, class, thickness, width, and roll dimensions.
6. Materials
6.1 Type I material is flexible, unsupported film.
6.2 Type II material is film meeting all of the requirements of Type I, and having a heat-sealable coating on one or both sides.
7. Requirements
7.1 The film covered by this specification shall meet the property requirements given in Tables 1-7 and Table 8 when tested
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.