ASTM A513-06a
(Specification)Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing
Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing
SCOPE
1.1 This specification covers electric-resistance-welded carbon and alloy steel tubing for use as mechanical tubing.
1.2 This specification covers mechanical tubing made from hot- or cold-rolled steel.
1.3 This specification covers round, square, rectangular, and special shape tubing.
1.4 Optional supplementary requirements are provided and when desired, shall be so stated in the order.
1.5 The values stated in inch-pound units are to be regarded as the standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 513 – 06a
Standard Specification for
Electric-Resistance-Welded Carbon and Alloy Steel
1
Mechanical Tubing
This standard is issued under the fixed designation A 513; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* E 570 Practice for Flux Leakage Examination of Ferromag-
netic Steel Tubular Products
1.1 This specification covers electric-resistance-welded car-
2.2 ANSI Standard:
bon and alloy steel tubing for use as mechanical tubing.
3
B 46.1 Surface Texture
1.2 This specification covers mechanical tubing made from
2.3 Military Standards:
hot- or cold-rolled steel.
4
MIL-STD-129 Marking for Shipment and Storage
1.3 This specification covers round, square, rectangular, and
MIL-STD-163 Steel Mill Products Preparation for Ship-
special shape tubing.
4
ment and Storage
Size Range
2.4 Federal Standard:
Type (Round Tubing)
1
4
Electric-Resistance-Welded Tubing outside diameter from ⁄2
Fed. Std. No. 123 Marking for Shipments (CivilAgencies)
from Hot-Rolled Steel to 15 in. (19.0 to 381.0 mm)
wall from 0.065 to 0.650 in.
3. Ordering Information
(1.65 to 16.50 mm)
3
Electric-Resistance-Welded Tubing outside diameter from ⁄8 to 12 in.
3.1 Orders for material under this specification should
from Cold-Rolled Steel (9.92 to 304.8 mm)
include the following as required to adequately describe the
wall from 0.022 to 0.134 in. (0.71
desired material:
to 3.40 mm)
3.1.1 Quantity (feet or number of lengths),
1.4 Optional supplementary requirements are provided and
3.1.2 Name of material (electric resistance-welded carbon
when desired, shall be so stated in the order.
or alloy steel mechanical tubing),
1.5 The values stated in inch-pound units are to be regarded
3.1.3 Types, conditions and code letters, (Sections 1 and
as the standard.
12),
3.1.4 Thermal condition, (12.2),
2. Referenced Documents
3.1.5 Flash condition, (12.3),
2
2.1 ASTM Standards:
3.1.6 Grade designation, if required, (Section 5),
A 370 Test Methods and Definitions for MechanicalTesting
3.1.7 Report chemical analysis and product analysis, if
of Steel Products
required (Sections 6 and 7),
E 1806 Practice for Sampling Steel and Iron for Determi-
3.1.8 Individual supplementary requirements, if required
nation of Chemical Composition
(S1 to S10, inclusive),
E 213 Practice for Ultrasonic Examination of Metal Pipe
3.1.9 Cross section (round, square, rectangular and special
and Tubing
shapes),
E 273 Practice for Ultrasonic Examination of the Weld
3.1.10 Dimensions, round, outside and inside and wall
Zone of Welded Pipe and Tubing
thickness (see 8.1 and 8.2) or square and rectangular, outside
E 309 Practice for Eddy-Current Examination of Steel Tu-
dimension and wall thickness and corner radii, if required (see
bular Products Using Magnetic Saturation
9.1 and 9.2),
3.1.11 Length, round, mill lengths or definite cut length (see
8.3), square and rectangular, specified length (see 9.4),
1
3.1.12 Squareness of cut, round tubing, if required, (see
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel, and RelatedAlloys and is the direct responsibility of Subcommittee
8.4),
A01.09 on Carbon Steel Tubular Products.
Current edition approved Sept. 1, 2006. Published September 2006. Originally
approved in 1964. Last previous edition approved in 2006 as A 513 – 06.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM 4th Floor, New York, NY 10036.
4
Standards volume information, refer to the standard’s Document Summary page on AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
the ASTM website. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A 513 – 06a
3.1.13 Burrs removed, if required (see 11.2), 6. Heat Analysis
3.1.14 Protective coating (see 14.1),
6.1 An analysis of each heat of steel shall be made by the
3.1.15 Special packaging (see 17.1),
steel manufacturer to determine the percentages of the ele-
3.1.16 Specification designation, ments specified; if secondary melting processes are employed,
the heat analysis shall be obtained from one remelted ingot or
3.1.17 End use,
the product of one remelted in
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A 513–06 Designation: A 513 – 06a
Standard Specification for
Electric-Resistance-Welded Carbon and Alloy Steel
1
Mechanical Tubing
This standard is issued under the fixed designation A 513; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification covers electric-resistance-welded carbon and alloy steel tubing for use as mechanical tubing.
1.2 This specification covers mechanical tubing made from hot- or cold-rolled steel.
1.3 This specification covers round, square, rectangular, and special shape tubing.
Size Range
Type (Round Tubing)
1
Electric-Resistance-Welded Tubing outside diameter from ⁄2
from Hot-Rolled Steel to 15 in. (19.0 to 381.0 mm)
wall from 0.065 to 0.650 in.
(1.65 to 16.50 mm)
3
Electric-Resistance-Welded Tubing outside diameter from ⁄8 to 12 in.
from Cold-Rolled Steel (9.92 to 304.8 mm)
wall from 0.022 to 0.134 in. (0.71
to 3.40 mm)
1.4 Optional supplementary requirements are provided and when desired, shall be so stated in the order.
1.5 The values stated in inch-pound units are to be regarded as the standard.
2. Referenced Documents
2
2.1 ASTM Standards:
A 370 Test Methods and Definitions for Mechanical Testing of Steel Products
E 1806 Practice for Sampling Steel and Iron for Determination of Chemical Composition
E 213 Practice for Ultrasonic Examination of Metal Pipe and Tubing
E 273 Practice for Ultrasonic Examination of the Weld Zone of Welded Pipe and Tubing
E 309 Practice for Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation
E 570 Practice for Flux Leakage Examination of Ferromagnetic Steel Tubular Products
2.2 ANSI Standard:
3
B 46.1 Surface Texture
2.3 Military Standards:
4
MIL-STD-129 Marking for Shipment and Storage
4
MIL-STD-163 Steel Mill Products Preparation for Shipment and Storage
2.4 Federal Standard:
4
Fed. Std. No. 123 Marking for Shipments (Civil Agencies)
3. Ordering Information
3.1 Orders for material under this specification should include the following as required to adequately describe the desired
material:
3.1.1 Quantity (feet or number of lengths),
3.1.2 Name of material (electric resistance-welded carbon or alloy steel mechanical tubing),
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel, and RelatedAlloys and is the direct responsibility of SubcommitteeA01.09
on Carbon Steel Tubular Products.
Current edition approved MaySept. 1, 2006. Published MaySeptember 2006. Originally approved in 1964. Last previous edition approved in 20002006 as A 513 – 006.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. ForAnnualBookofASTMStandards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036.
4
Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A 513 – 06a
3.1.3Type, description and code letters, (Section
3.1.3 Types, conditions and code letters, (Sections 1 and 12.1and 12),
3.1.4 Thermal condition, (12.2),
3.1.5 Flash condition, (12.3),
3.1.6 Grade designation, if required, (Section 5),
3.1.7 Report chemical analysis and product analysis, if required (Sections 6 and 7),
3.1.8 Individual supplementary requirements, if required (S1 to S10, inclusive),
3.1.9 Cross section (round, square, rectangular and special shapes),
3.1.10 Dimensions, round, outside and inside and wall thickness (see 8.1 and 8.2) or square and rectangular, outside dimension
and wall thickness and corner radii, if required (see 9.1 and 9.2),
3.1.11Surface finish (see 11.2),
3.1.12Length, round, mill lengths or definite cut length (see
3.1.11 Length, round, mill lengths or definite cut length (see 8.3), square and rectangular, specified length (see 9.4),
3.1.132 Squareness of cut, round tubing, if required, (see 8.4),
3.1.14B
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.