ASTM F2971-13(2021)
(Practice)Standard Practice for Reporting Data for Test Specimens Prepared by Additive Manufacturing
Standard Practice for Reporting Data for Test Specimens Prepared by Additive Manufacturing
SIGNIFICANCE AND USE
4.1 Due to variables unique to each AM process and piece of equipment, it is critical to standardize descriptions used to report the preparation, processing, and post processing of specimens produced for tests or evaluation. The intent of this practice is to consistently document the materials and processing history associated with specimens undergoing test or evaluation. The level of detail for the documentation will match the application.
4.2 This practice establishes minimum data element requirements for reporting of material and process data for the purpose of:
4.2.1 Standardizing test specimen descriptions and test reports,
4.2.2 Assisting designers by standardizing AM materials databases,
4.2.3 Aiding material traceability through testing and evaluation,
4.2.4 Capturing property-parameter-performance relationships of AM specimens to enable predictive modeling and other computational approaches.
SCOPE
1.1 This practice describes a standard procedure for reporting results by testing or evaluation of specimens produced by additive manufacturing (AM). This practice provides a common format for presenting data for AM specimens, for two purposes: (1) to establish further data reporting requirements, and (2) to provide information for the design of material property databases.
1.2 The values stated in SI units are required for all additive manufacturing related standards. However, when this standard is used in combination with any test method or equipment specified in inch-pound units the results should be reported with mathematical conversions to SI units immediately following in parentheses. The conversions shall be provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2971 − 13 (Reapproved 2021)
Standard Practice for
Reporting Data for Test Specimens Prepared by Additive
Manufacturing
This standard is issued under the fixed designation F2971; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope [Metric] (Withdrawn 2008)
F2792 Terminology for Additive Manufacturing Technolo-
1.1 This practice describes a standard procedure for report-
gies (Withdrawn 2015)
ing results by testing or evaluation of specimens produced by
F2921 Terminology for Additive Manufacturing—
additive manufacturing (AM). This practice provides a com-
Coordinate Systems and Test Methodologies
mon format for presenting data for AM specimens, for two
F2924 Specification for Additive Manufacturing Titanium-6
purposes: (1) to establish further data reporting requirements,
Aluminum-4 Vanadium with Powder Bed Fusion
and (2) to provide information for the design of material
property databases.
3. Terminology
1.2 The values stated in SI units are required for all additive
3.1 Definitions—shall be in accordance with Terminologies
manufacturing related standards. However, when this standard
F2792 and F2921.
is used in combination with any test method or equipment
4. Significance and Use
specified in inch-pound units the results should be reported
with mathematical conversions to SI units immediately follow-
4.1 Due to variables unique to each AM process and piece
ing in parentheses. The conversions shall be provided for
of equipment, it is critical to standardize descriptions used to
information only and are not considered standard.
report the preparation, processing, and post processing of
specimens produced for tests or evaluation. The intent of this
1.3 This standard does not purport to address all of the
practice is to consistently document the materials and process-
safety concerns, if any, associated with its use. It is the
ing history associated with specimens undergoing test or
responsibility of the user of this standard to establish appro-
evaluation. The level of detail for the documentation will
priate safety, health, and environmental practices and deter-
match the application.
mine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accor-
4.2 Thispracticeestablishesminimumdataelementrequire-
dance with internationally recognized principles on standard-
mentsforreportingofmaterialandprocessdataforthepurpose
ization established in the Decision on Principles for the
of:
Development of International Standards, Guides and Recom-
4.2.1 Standardizing test specimen descriptions and test
mendations issued by the World Trade Organization Technical
reports,
Barriers to Trade (TBT) Committee.
4.2.2 Assisting designers by standardizing AM materials
databases,
2. Referenced Documents 4.2.3 Aiding material traceability through testing and
evaluation,
2.1 ASTM Standards:
4.2.4 Capturing property-parameter-performance relation-
D638 Test Method for Tensile Properties of Plastics
ships of AM specimens to enable predictive modeling and
E8M Test Methods forTensionTesting of Metallic Materials
other computational approaches.
5. Requirements
This practice is under the jurisdiction of ASTM Committee F42 on Additive
5.1 This section specifies the data and information required
Manufacturing Technologies and is the direct responsibility of Subcommittee
to be reported for test specimens built using AM.
F42.01 on Test Methods.
5.1.1 Materials and Process Reporting Requirements—The
Current edition approved July 15, 2021. Published August 2021. Originally
approved in 2013. Last previous edition approved in 2013 as F2971–13. DOI:
following materials and processes information must be re-
10.1520/F2971-13R21
ported for test specimens built using AM:
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F2971 − 13 (2021)
5.1.1.1 All standard material specifications used. Informa- (1) The shape and dimensions of the test specimens, with
tion from these specifications should include, as minimum: tolerances specified.
(1) Description and preparation of feedstock materials
(2) The test plan. Note: this can be incorporated in the
required for AM operations.
materials and process specifications.
(2) Procedure for using or re-using feedstock material.
(3) Test procedures.
5.1.1.2 A description of all non-standard processes used or
(4) Non-destructive inspection procedures and results.
deviations, or both, from process standards used.
5.1.2.2 A description of all non-standard test methods used
5.1.1.3 All standard process specifications used. Informa-
or deviations, or both, from standard test methods used.
tion form these specifications should include, as a minimum:
5.1.2.3 Post Processing Reporting Requirements—If post
(1) All processes used to produce the specimen from
processing was performed on the test specimens and is not
feedstock material.
included in 5.1.1 or 5.1.2, then it must be reported. Post
(2) Placement and orientation of the test specimen in the
processing may include, but is not limited to support removal,
build chamber.
stress relief, part consolidation, heat treatment, and surface
5.1.1.4 A description of all non-standard processes used or
finishing.
deviations, or both, from process standards used.
5.1.2 Test and Inspection Reporting Requirements—The
following test and inspection information must be reported for 6. Keywords
test specimens built using AM:
6.1 additive manufacturing; reporting requirements
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.