ASTM D3543-17
(Test Method)Standard Test Method for Metal Glide Adhesion
Standard Test Method for Metal Glide Adhesion
SIGNIFICANCE AND USE
3.1 This test method is used to determine the effect of plasticizers in tile on the floor polish itself. If the floor polish is softened by the plasticizers in the tile it will become an adhesive and adhere to the metal glide that is placed on the polish under standard weights at standard temperatures. Various degrees of attack on the polish are evaluated by the damage to the tile underneath the polish.
SCOPE
1.1 This test method2 covers a laboratory procedure for determining damage resulting from metal glide adhesion on floor surfaces.
1.2 The values stated in SI units are to be regarded as the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautions are given in 8.2.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D3543 − 17
Standard Test Method for
1
Metal Glide Adhesion
This standard is issued under the fixed designation D3543; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope is softened by the plasticizers in the tile it will become an
2 adhesive and adhere to the metal glide that is placed on the
1.1 This test method covers a laboratory procedure for
polish under standard weights at standard temperatures. Vari-
determining damage resulting from metal glide adhesion on
ousdegreesofattackonthepolishareevaluatedbythedamage
floor surfaces.
to the tile underneath the polish.
1.2 The values stated in SI units are to be regarded as the
4. Apparatus
standard.
1.3 This standard does not purport to address all of the 4.1 Metal Glide Adhesion Tester.
safety concerns, if any, associated with its use. It is the 4,5
4.2 Metal Glides.
responsibility of the user of this standard to establish appro-
4.3 Oven, or other facility, capable of maintaining 37.8 6
priate safety and health practices and determine the applica-
2.8°C(100 65°F)andlargeenoughtoaccommodatethemetal
bility of regulatory limitations prior to use. Specific precau-
glide adhesion tester.
tions are given in 8.2.
1.4 This international standard was developed in accor- 4.4 Black Offıcial Vinyl Composition Tile, 304.8 by 304.8
6
dance with internationally recognized principles on standard- mm (12 by 12 in.).
ization established in the Decision on Principles for the
4.5 Steel Wool (00 grade or finer).
Development of International Standards, Guides and Recom-
7
5. Description of Metal Glide Adhesion Apparatus
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
5.1 The test apparatus (Figs. 1-3) consists of three basic
parts: a housing frame, a support cover, and nine brass weights
2. Referenced Documents
and metal glides.
3
2.1 ASTM Standards:
5.1.1 The housing frame consists of base plate A, frame
D1436 Test Methods for Application of Emulsion Floor
sections C and D, all made of plastic, and support plate B,
Polishes to Substrates for Testing Purposes
made of plate glass (see Fig. 1).
D3153 Test Method for Recoatability of Water-Emulsion
5.1.2 The support cover is constructed of plastic and fits
Floor Polishes
snugly onto the housing frame. The nine tubes allow for
supportingandpositioningofuptoninebrassweights(seeFig.
3. Significance and Use
2).
3.1 This test method is used to determine the effect of
plasticizers in tile on the floor polish itself. If the floor polish
4
Metal glides, 0.035–in. cold roll temper 5, nickel plate, |n & -in. base diameter,
available from Faultless Caster Corp., Evansville, IN, or their equivalent, have been
1
ThistestmethodisunderthejurisdictionofASTMCommitteeD21onPolishes found satisfactory.
5
and is the direct responsibility of Subcommittee D21.04 on Performance Tests. Thisisthesolesourceofsupplyoftheapparatusknowntothecommitteeatthis
Current edition approved March 1, 2017. Published April 2017. Originally time. If you are aware of alternative suppliers, please provide this information to
approved in 1976. Last previous edition approved in 2016 as D3543 – 93 (2016). ASTM International Headquarters. Your comments will receive careful consider-
1
DOI: 10.1520/D3543-17. ation at a meeting of the responsible technical committee, which you may attend.
2 6
The test method is empirical in that it allows a comparison of the relative OVCT tile may be obtained through Armstrong Flooring from various home
performance of up to three polishes on the same substrate for each test. It also improvement stores. The following Armstrong tile substrates have been found to
permits comparison of two polishes with an uncoated portion of the substrate for perform adequately for this test method: Armstrong Excelon Feature Tile: Black
each test. (56790), http://www.armstrong.com/commflooringna/product_details_toolbox_
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or magnify.jsp?item_id=47394.
7
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM The preferred material for constructing housing frame and support cover is
Standards volume information, refer to the standard’s Document Summary page on plastic such as poly(methyl methacrylate). However, other materials of construction
the ASTM website. may be used provided that variables are not introduced due to warping or bending.
Copyright © ASTM Inter
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3543 − 93 (Reapproved 2016) D3543 − 17
Standard Test Method for
1
Metal Glide Adhesion
This standard is issued under the fixed designation D3543; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
2
1.1 This test method covers a laboratory procedure for determining damage resulting from metal glide adhesion on floor
surfaces.
1.2 The values stated in SI units are to be regarded as the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. Specific precautions are given in 8.2.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
D1436 Test Methods for Application of Emulsion Floor Polishes to Substrates for Testing Purposes
D3153 Test Method for Recoatability of Water-Emulsion Floor Polishes
3. Significance and Use
3.1 This test method is used to determine the effect of plasticizers in tile on the floor polish itself. If the floor polish is softened
by the plasticizers in the tile it will become an adhesive and adhere to the metal glide that is placed on the polish under standard
weights at standard temperatures. Various degrees of attack on the polish are evaluated by the damage to the tile underneath the
polish.
4. Apparatus
4.1 Metal Glide Adhesion Tester.
4,5
4.2 Metal Glides.
4.3 Oven, or other facility, capable of maintaining 37.8 6 2.8°C (100 6 5°F) and large enough to accommodate the metal glide
adhesion tester.
6,
4.4 Black Offıcial Vinyl Composition Tile, 304.8 by 304.8 mm (12 by 12 in.).
4.5 Steel Wool (00 grade or finer).
1
This test method is under the jurisdiction of ASTM Committee D21 on Polishes and is the direct responsibility of Subcommittee D21.04 on Performance Tests.
Current edition approved Oct. 1, 2016March 1, 2017. Published October 2016April 2017. Originally approved in 1976. Last previous edition approved in 20082016 as
D3543 – 93 (2008).(2016). DOI: 10.1520/D3543-93R16.10.1520/D3543-17.
2
The test method is empirical in that it allows a comparison of the relative performance of up to three polishes on the same substrate for each test. It also permits
comparison of two polishes with an uncoated portion of the substrate for each test.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Metal glides, 0.035–in. cold roll temper 5, nickel plate, |n & -in. base diameter, available from Faultless Caster Corp., Evansville, IN, or their equivalent, have been found
satisfactory.
5
This is the sole source of supply of the apparatus known to the committee at this time. If you are aware of alternative suppliers, please provide this information to ASTM
1
International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
6
Available from Chemical Specialties Manufacturers Assoc., 1913 Eye St., N.W. Washington, DC 20006.OVCT tile may be obtained through Armstrong Flooring from
various home improvement stores. The following Armstrong tile substrates have been found to perform adequately for this test method: Armstrong Excelon Feature Tile: Black
(56790), http://www.armstrong.com/commflooringna/product_details_toolbox_magnify.jsp?item_id=47394.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3543 − 17
7
5. Description of Metal Glide Adhesion Apparatus
5.1 The test apparatus (Figs. 1-3) consists of three basic parts: a housing frame, a support cover, and nine brass weights and
metal glides.
5.1.1 The housing frame consists of base plate A, frame sections C
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.