iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E177-13

(Practice)

Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods

Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods

SIGNIFICANCE AND USE
4.1 Part A of the “Blue Book,” Form and Style for ASTM Standards, requires that all test methods include statements of precision and bias. This practice discusses these two concepts and provides guidance for their use in statements about test methods.  
4.2 Precision—A statement of precision allows potential users of a test method to assess in general terms the test method's usefulness with respect to variability in proposed applications. A statement of precision is not intended to exhibit values that can be exactly duplicated in every user's laboratory. Instead, the statement provides guidelines as to the magnitude of variability that can be expected between test results when the method is used in one, or in two or more, reasonably competent laboratories. For a discussion of precision, see 8.1.  
4.3 Bias—A statement of bias furnishes guidelines on the relationship between a set of typical test results produced by the test method under specific test conditions and a related set of accepted reference values (see 9.1).  
4.3.1 An alternative term for bias is trueness, which has a positive connotation, in that greater bias is associated with less favorable trueness. Trueness is the systematic component of accuracy.  
4.4 Accuracy—The term “accuracy,” used in earlier editions of Practice E177, embraces both precision and bias (see 9.3).
SCOPE
1.1 The purpose of this practice is to present concepts necessary to the understanding of the terms “precision” and “bias” as used in quantitative test methods. This practice also describes methods of expressing precision and bias and, in a final section, gives examples of how statements on precision and bias may be written for ASTM test methods.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

General Information

Status
Historical
Publication Date
30-Apr-2013
ICS
19.020 - Test conditions and procedures in general
Technical Committee
E11 - Quality and Statistics
Drafting Committee
E11.20 - Test Method Evaluation and Quality Control
Current Stage
Ref Project

Relations

Replaces
ASTM E177-10 - Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
Effective Date
01-May-2013
Replaced By
ASTM E177-14 - Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
Effective Date
01-May-2014
Referred By
ASTM E1876-22 - Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio by Impulse Excitation of Vibration
Effective Date
01-May-2013
Referred By
ASTM A1013-00(2020) - Standard Test Method for High-Frequency (10 kHz-1 MHz) Core Loss of Soft Magnetic Core Components at Controlled Temperatures Using the Voltmeter-Ammeter-Wattmeter Method
Effective Date
01-May-2013
Referred By
ASTM F2004-17 - Standard Test Method for Transformation Temperature of Nickel-Titanium Alloys by Thermal Analysis
Effective Date
01-May-2013
Referred By
ASTM D2866-11(2018) - Standard Test Method for Total Ash Content of Activated Carbon
Effective Date
01-May-2013
Referred By
ASTM D5349-19 - Standard Test Method for Determination of the Moisture and Volatile Content of Sulfonated, Sulfated Oils and Fatliquors by Oven Method
Effective Date
01-May-2013
Referred By
ASTM D2412-21 - Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
Effective Date
01-May-2013
Referred By
ASTM D6817/D6817M-17(2021) - Standard Specification for Rigid Cellular Polystyrene Geofoam
Effective Date
01-May-2013
Referred By
ASTM D4782-10(2016) - Standard Test Method for Palladium in Molecular Sieve Catalyst by Wet Chemistry
Effective Date
01-May-2013
Referred By
ASTM D3530-20 - Standard Test Method for Volatiles Content of Composite Material Prepreg
Effective Date
01-May-2013
Referred By
ASTM D1316-20 - Standard Test Method for Fineness of Grind of Printing Inks By the NPIRI Grindometer
Effective Date
01-May-2013
Referred By
ASTM E132-17 - Standard Test Method for Poisson’s Ratio at Room Temperature
Effective Date
01-May-2013
Referred By
ASTM C430-17 - Standard Test Method for Fineness of Hydraulic Cement by the 45-μm (No. 325) Sieve
Effective Date
01-May-2013
Referred By
ASTM F1165-20 - Standard Test Method for Measuring Angular Displacement of Multiple Images in Transparent Parts
Effective Date
01-May-2013

Buy Standard

ASTM E177-13 - Standard Practice for Use of the Terms Precision and Bias in ASTM Test MethodsASTM E177-13 - Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
PreviousNext
Standard
ASTM E177-13 - Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM E177-13 - Standard Practice for Use of the Terms Precision and Bias in ASTM Test MethodsREDLINE ASTM E177-13 - Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
PreviousNext
Standard
REDLINE ASTM E177-13 - Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E177 − 13 AnAmerican National Standard
Standard Practice for
1
Use of the Terms Precision and Bias in ASTM Test Methods
This standard is issued under the fixed designation E177; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope (3) a consensus or certified value, based on collaborative
experimental work under the auspices of a scientific or
1.1 The purpose of this practice is to present concepts
engineering group.
necessary to the understanding of the terms “precision” and
3.1.1.1 Discussion—A national or international
“bias” as used in quantitative test methods. This practice also
organization, referred to in 3.1.1 (2), generally maintains
describes methods of expressing precision and bias and, in a
measurement standards to which the reference values obtained
final section, gives examples of how statements on precision
are traceable.
and bias may be written for ASTM test methods.
3.1.2 accuracy, n—the closeness of agreement between a
1.2 This standard does not purport to address all of the
test result and an accepted reference value.
safety concerns, if any, associated with its use. It is the
3.1.2.1 Discussion—The term accuracy, when applied to a
responsibility of the user of this standard to establish appro-
set of test results, involves a combination of a random
priate safety and health practices and determine the applica-
component and of a common systematic error or bias compo-
bility of regulatory requirements prior to use.
nent.
2. Referenced Documents
3.1.3 bias, n—the difference between the expectation of the
2
test results and an accepted reference value.
2.1 ASTM Standards:
3.1.3.1 Discussion—Bias is the total systematic error as
E456 Terminology Relating to Quality and Statistics
contrasted to random error. There may be one or more
E691 Practice for Conducting an Interlaboratory Study to
systematic error components contributing to the bias. A larger
Determine the Precision of a Test Method
systematic difference from the accepted reference value is
E1488 GuideforStatisticalProcedurestoUseinDeveloping
reflected by a larger bias value.
and Applying Test Methods
E2282 Guide for Defining the Test Result of a Test Method 3.1.4 characteristic, n—a property of items in a sample or
E2586 Practice for Calculating and Using Basic Statistics
population which, when measured, counted or otherwise
E2587 Practice for Use of Control Charts in Statistical observed, helps to distinguish between the items. E2282
Process Control
3.1.5 coeffıcient of variation, CV, n—for a nonnegative
characteristic, the ratio of the standard deviation to the mean
3. Terminology
for a population or sample. E2586
3.1 Definitions—Terminology E456 provides a more exten-
3.1.6 intermediate precision, n—the closeness of agreement
sive list of terms in E11 standards.
between test results obtained under specified intermediate
3.1.1 accepted reference value, n—a value that serves as an
precision conditions.
agreed-upon reference for comparison, and which is derived
3.1.6.1 Discussion—The specific measure and the specific
as: (1) a theoretical or established value, based on scientific
conditions must be specified for each intermediate measure of
principles, (2) an assigned or certified value, based on experi-
precision; thus, “standard deviation of test results among
mental work of some national or international organization, or
operators in a laboratory,” or “day-to-day standard deviation
within a laboratory for the same operator.”
1
This practice is under the jurisdiction ofASTM Committee E11 on Quality and
3.1.6.2 Discussion—Because the training of operators, the
Statistics and is the direct responsibility of Subcommittee E11.20 on Test Method
agreement of different pieces of equipment in the same
Evaluation and Quality Control.
laboratory and the variation of environmental conditions with
Current edition approved May 1, 2013. Published May 2013. Originally
longer time intervals all depend on the degree of within-
approved in 1961. Last previous edition approved in 2010 as E177 – 10. DOI:
10.1520/E0177-13.
laboratory control, the intermediate measures of precision are
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
likely to vary appreciably from laboratory to laboratory. Thus,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
intermediate precisions may be more characteristic of indi-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. vidual lab
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E177 − 10 E177 − 13 An American National Standard
Standard Practice for
1
Use of the Terms Precision and Bias in ASTM Test Methods
This standard is issued under the fixed designation E177; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 The purpose of this practice is to present concepts necessary to the understanding of the terms “precision” and “bias” as used
in quantitative test methods. This practice also describes methods of expressing precision and bias and, in a final section, gives
examples of how statements on precision and bias may be written for ASTM test methods.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
requirements prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
E178 Practice for Dealing With Outlying Observations
E456 Terminology Relating to Quality and Statistics
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
E1488 Guide for Statistical Procedures to Use in Developing and Applying Test Methods
E2282 Guide for Defining the Test Result of a Test Method
E2586 Practice for Calculating and Using Basic Statistics
E2587 Practice for Use of Control Charts in Statistical Process Control
3. Terminology
3.1 Definitions:Definitions
3.1.1 Terminology E456 provides a more extensive list of terms in E11 standards.—Terminology E456 provides a more
extensive list of terms in E11 standards.
3.1.1 accepted reference value, n—a value that serves as an agreed-upon reference for comparison, and which is derived as: (1)
a theoretical or established value, based on scientific principles, (2) an assigned or certified value, based on experimental work of
some national or international organization, or (3) a consensus or certified value, based on collaborative experimental work under
the auspices of a scientific or engineering group.
1
This practice is under the jurisdiction of ASTM Committee E11 on Quality and Statistics and is the direct responsibility of Subcommittee E11.20 on Test Method
Evaluation and Quality Control.
Current edition approved Oct. 1, 2010May 1, 2013. Published November 2010May 2013. Originally approved in 1961. Last previous edition approved in 20082010 as
E177 – 08.E177 – 10. DOI: 10.1520/E0177-10.10.1520/E0177-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3.1.1.1 Discussion—
A national or international organization, referred to in 3.1.23.1.1 (2), generally maintains measurement standards to which the
reference values obtained are traceable.
3.1.2 accuracy, n—the closeness of agreement between a test result and an accepted reference value.
3.1.2.1 Discussion—
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E177 − 13
The term accuracy, when applied to a set of test results, involves a combination of a random component and of a common
systematic error or bias component.
3.1.3 bias, n—the difference between the expectation of the test results and an accepted reference value.
3.1.3.1 Discussion—
Bias is the total systematic error as contrasted to random error. There may be one or more systematic error components contributing
to the bias. A larger systematic difference from the accepted reference value is reflected by a larger bias value.
3.1.4 characteristic, n—a property of items in a sample or population which, when measured, counted or otherwise observed,
helps to distinguish between the items. E2282
3.1.5 coeffıcient of variation, CV, n—for a nonnegative characteristic, the ratio of the standard deviation to the mean for a
population or sample. E2586
3.1.6 intermediate precision, n—the closeness of agreement between test results obtained under specified intermediate precision
conditions.
3.1.6.1 Discussion—
The spec
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E2282-23(Guide)
Standard Guide for Defining the Test Result of a Test Method

ABSTRACT
The purpose of this guide is to provide guidelines for identifying the elements that comprise the test result of a test method and to illustrate how these elements combine into the test result. It covers the types of measurement scales used for expressing observations and test results. This guide provides information on the construction of test results from more elemental measurements.
SIGNIFICANCE AND USE
4.1 All test methods have an output in the form of a test result. This guide provides information on the construction of test results from more elemental measurements.  
4.2 A well-defined test result is necessary before any precision statements can be made about the test method.  
4.2.1 Form and Style for ASTM Standards,2 Section A21, requires that every test method shall contain a statement regarding its precision, preferably as a result of an interlaboratory test program. Reporting of such studies is described in Practice E177, which illustrates the development of test results from observations and test determinations.  
4.2.2 Precision statements for ASTM test methods are applicable to test results. They are not applicable to test determinations or observations, unless specifically and clearly indicated otherwise.
SCOPE
1.1 This standard provides guidelines for identifying the elements that comprise the test result of a test method and to illustrate how these elements combine into the test result.  
1.2 Types of measurement scales used for expressing observations and test results are discussed.  
1.3 No system of units is specified in this standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1488-23(Guide)
Standard Guide for Statistical Procedures to Use in Developing and Applying Test Methods

ABSTRACT
This guide identifies statistical procedures for use in developing new test methods or revising or evaluating existing test methods, or both. It also cites statistical procedures especially useful in the application of test methods. This standard recommends what approaches may be taken and indicates which standards may be used to perform such assessments.
SIGNIFICANCE AND USE
4.1 The creation of a standardized test method generally follows a series of steps from inception to approval and ongoing use. In all such stages there are questions of how well the test method performs.  
4.1.1 Assessments of a new or existing test method generally involve statistical planning and analysis. This standard recommends what approaches may be taken and indicates which standards may be used to perform such assessments.  
4.2 This standard introduces a series of phases which are recommended to be considered during the life cycle of a test method as depicted in Fig. 1. These begin with a design phase where the standard is initially prepared. A development phase involves a variety of experiments that allow further refinement and understanding of how the test method performs within a laboratory. In an evaluation phase the test method is then examined by way of interlaboratory studies resulting in precision and bias statistics which are published in the standard. Finally, the test method is subject to a monitoring phase.
FIG. 1 Sequence of Steps  
4.3 All ASTM test methods are required to include statements on precision and bias.3  
4.4 Since ASTM began to require all test methods to have precision and bias statements that are based on interlaboratory studies, there has been increased concern regarding what statistical experiments and procedures to use during the development of the test methods. Although there exists a wide range of statistical procedures, there is a small group of generally accepted techniques that are beneficial to follow. This guide is designed to provide a brief overview of these procedures and to suggest an appropriate sequence of conducting these procedures.  
4.5 Statistical procedures often result in interpretations that are not absolutes. Sometimes the information obtained may be inadequate or incomplete, which may lead to additional questions and the need for further experimentation. Information outside the data is also impo...
SCOPE
1.1 This guide identifies statistical procedures for use in developing new test methods or revising or evaluating existing test methods, or both.  
1.2 This guide also cites statistical procedures especially useful in the application of test methods.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    9 pages
    English language
    sale 15% off
  • Guide
    9 pages
    English language
    sale 15% off
ASTM
ASTM E1402-13(2023)(Guide)
Standard Guide for Sampling Design

ABSTRACT
This guide defines terms and introduces basic methods for probability sampling of discrete populations, areas, and bulk materials. It provides an overview of common probability sampling methods employed by users of ASTM standards. This guide also describes the principal types of sampling designs and provides formulas for estimating population means and standard errors of the estimates.
SIGNIFICANCE AND USE
4.1 This guide describes the principal types of sampling designs and provides formulas for estimating population means and standard errors of the estimates. Practice E105 provides principles for designing probability sampling plans in relation to the objectives of study, costs, and practical constraints. Practice E122 aids in specifying the required sample size. Practice E141 describes conditions to ensure validity of the results of sampling. Further description of the designs and formulas in this guide, and beyond it, can be found in textbooks (1-10).3  
4.2 Sampling, both discrete and bulk, is a clerical and physical operation. It generally involves training enumerators and technicians to use maps, directories and stop watches so as to locate designated sampling units. Once a sampling unit is located at its address, discrete sampling and area sampling enumeration proceeds to a measurement. For bulk sampling, material is extracted into a composite.  
4.3 A sampling plan consists of instructions telling how to list addresses and how to select the addresses to be measured or extracted. A frame is a listing of addresses each of which is indexed by a single integer or by an n-tuple (several integer) number. The sampled population consists of all addresses in the frame that can actually be selected and measured. It is sometimes different from a targeted population that the user would have preferred to be covered.  
4.4 A selection scheme designates which indexes constitute the sample. If certified random numbers completely control the selection scheme the sample is called a probability sample. Certified random numbers are those generated either from a table (for example, Ref (11)) that has been tested for equal digit frequencies and for serial independence, from a computer program that was checked to have a long cycle length, or from a random physical method such as tossing of a coin or a casino-quality spinner.  
4.5 The objective of sampling is often to estimate t...
SCOPE
1.1 This guide defines terms and introduces basic methods for probability sampling of discrete populations, areas, and bulk materials. It provides an overview of common probability sampling methods employed by users of ASTM standards.  
1.2 Sampling may be done for the purpose of estimation, of comparison between parts of a sampled population, or for acceptance of lots. Sampling is also used for the purpose of auditing information obtained from complete enumeration of the population.  
1.3 No system of units is specified in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM E691-23(Practice)
Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

ABSTRACT
This practice describes the techniques for planning, conducting, analyzing, and treating the results of an interlaboratory study (ILS) of a test method. The statistical techniques described in this practice provide adequate information for formulating the precision statement of a test method. This practice is also concerned exclusively with test methods which yield a single numerical figure as the test result, although the single figure may be the outcome of a calculation from a set of measurements. ASTM regulations require precision statements in all test methods in terms of repeatability and reproducibility and knowledge of the test method precision is useful in commerce and in technical work when comparing test results against standard values or between data sources.
SIGNIFICANCE AND USE
4.1 ASTM regulations require precision statements in all test methods in terms of repeatability and reproducibility. This practice may be used in obtaining the needed information as simply as possible. This information may then be used to prepare a precision statement in accordance with Practice E177. Knowledge of the test method precision is useful in commerce and in technical work when comparing test results against standard values (such as specification limits) or between data sources (different laboratories, instruments, etc.).  
4.1.1 When a test method is applied to a large number of portions of a material that are as nearly alike as possible, the test results obtained will not all have the same value. A measure of the degree of agreement among these test results describes the precision of the test method for that material. Numerical measures of the variability between such test results provide inverse measures of the precision of the test method. Greater variability implies smaller (that is, poorer) precision and larger imprecision.  
4.1.2 Precision is reported as a standard deviation, coefficient of variation (relative standard deviation), variance, or a precision limit (a data range indicating no statistically significant difference between test results).  
4.1.3 This practice is designed only to estimate the precision of a test method. However, when accepted reference values are available for the property levels, the test result data obtained according to this practice may be used in estimating the bias of the test method. For a discussion of bias estimation and the relationships between precision, bias, and accuracy, see Practice E177.  
4.2 The procedures presented in this practice consist of three basic steps: planning the interlaboratory study, guiding the testing phase of the study, and analyzing the test result data.  
4.2.1 The planning phase includes forming the ILS task group, the study design, selection, and number of participating laborato...
SCOPE
1.1 This practice describes the techniques for planning, conducting, analyzing, and treating the results of an interlaboratory study (ILS) of a test method. The statistical techniques described in this practice provide adequate information for formulating the precision statement of a test method.  
1.2 This practice does not concern itself with the development of test methods but rather with gathering the information needed for a test method precision statement after the development stage has been successfully completed. The data obtained in the interlaboratory study may indicate, however, that further effort is needed to improve the test method.  
1.3 Since the primary purpose of this practice is the development of the information needed for a precision statement, the experimental design in this practice may not be optimum for evaluating materials, apparatus, or individual laboratories.  
1.4 Field of Application—This practice is concerned exclusively with test methods which yield a single numerical figure as the test result, although the single figure may be the outcome of a calculation from a set of measurements.  
1.4.1 This practice ...

  • Standard
    23 pages
    English language
    sale 15% off
  • Standard
    23 pages
    English language
    sale 15% off
ASTM
ASTM E29-22(Practice)
Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

ABSTRACT
This practice is intended to assist the various technical committees in the use of uniform methods of indicating the number of digits which are to be considered significant in specification limits, for example, specified maximum values and specified minimum values. This practice is also intended to be used in determining conformance with specifications when the applicable ASTM specifications or standards make a direct reference.
SCOPE
1.1 This practice is intended to assist the various technical committees in the use of uniform methods of indicating the number of digits which are to be considered significant in specification limits, for example, specified maximum values and specified minimum values. Its aim is to outline methods which should aid in clarifying the intended meaning of specification limits with which observed values or calculated test results are compared in determining conformance with specifications.  
1.2 This practice is intended to be used in determining conformance with specifications when the applicable ASTM specifications or standards make direct reference to this practice.  
1.3 Reference to this practice is valid only when a choice of method has been indicated, that is, either absolute method or rounding method.  
1.4 The system of units for this practice is not specified. Dimensional quantities in the practice are presented only as illustrations of calculation methods. The examples are not binding on products or test methods treated.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E1169-21(Practice)
Standard Practice for Conducting Ruggedness Tests

SIGNIFICANCE AND USE
4.1 A ruggedness test is a special application of a statistically designed experiment that makes changes in the test method variables, called factors, and then calculates the subsequent effect of those changes upon the test results. Factors are features of the test method or of the laboratory environment that are known to vary across laboratories and are subject to control by the test method.  
4.1.1 Statistical design enables more efficient and cost-effective determination of the factor effects than would be achieved if separate experiments were carried out for each factor. The proposed designs are easy to use in developing the information needed for evaluating quantitative test methods.  
4.2 In ruggedness testing, the two levels (settings) for each factor are chosen to use moderate separations between the high and low settings. In general, if there is an underlying difference between the levels, then the size of effects will increase with increased separation between the high and low settings of the factors. A run is an execution of the test method under prescribed settings of each of the factors under study. A ruggedness test consists of a set of runs.  
4.3 A ruggedness test is usually conducted within a single laboratory on uniform material, so that the effects of changing only the factors are measured. The results may then be used to assist in determining the degree of control required of factors described in the test method.  
4.4 Ruggedness testing should precede an interlaboratory (round robin) study to correct any deficiencies in the test method and may also be part of the validation phase of developing a standard test method as described in Guide E1488.  
4.5 This standard discusses design and analysis of ruggedness testing in Section 5 and contains an example of a basic eight run design. Some caution must be used in interpretation of results, since interaction effects may be present. These effects are present when a factor effect changes with the ...
SCOPE
1.1 This practice covers conducting ruggedness tests. The purpose of a ruggedness test is to identify those factors that strongly influence the measurements provided by a specific test method and to estimate how closely those factors need to be controlled.  
1.2 This practice restricts itself to experimental designs with two levels per factor. The designs require the simultaneous change of the levels of all of the factors, thus permitting the determination of the effects of each of the factors on the measured results.  
1.3 The system of units for this practice is not specified. Dimensional quantities in the practice are presented only as illustrations of calculation methods. The examples are not binding on products or test methods treated.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    17 pages
    English language
    sale 15% off
  • Standard
    17 pages
    English language
    sale 15% off
ASTM
ASTM E1325-21(Terminology)
Standard Terminology Relating to Design of Experiments

ABSTRACT
This standard includes those statistical items related to the area of design of experiments for which standard definitions appear desirable. It provides definitions, descriptions, discussion, and comparison of terms.
SIGNIFICANCE AND USE
3.1 This standard is a subsidiary to Terminology E456.  
3.2 It provides definitions, descriptions, discussion, and comparison of terms.
SCOPE
1.1 This standard includes those statistical items related to the area of design of experiments for which standard definitions appear desirable.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM E3264-21(Guide)
Standard Guide for Homogeneity of Samples and Reference Materials Used for Inter- and Intra-Laboratory Studies

SIGNIFICANCE AND USE
5.1 This guide presents techniques and guidance for evaluating and assuring homogeneity of individual samples or bulk materials and can be used for either interlaboratory or intra-laboratory studies. The types of studies include, but are not limited to, studies to determine precision estimates for test methods, proficiency testing programs, and studies related to quality control of testing within a single laboratory.  
5.2 Because the test results of any laboratory study are affected by the quality of the samples tested, producing homogeneous samples and determining the degree of homogeneity is important for interpreting the results of the study.  
5.3 Five techniques are presented in this guide to evaluate sample homogeneity for a range of circumstances and degrees of rigor. The circumstances under which the studies are conducted and the degree of rigor required may differ. The user should consider the circumstances listed in each technique to determine which is appropriate for the study at hand.  
5.4 Each of the Techniques 1, 2, and 3 provides a procedure for testing and evaluating sample homogeneity when replicate testing of the samples is possible. Technique 4 provides a plan to evaluate sample homogeneity when replicate testing is not possible. Technique 5 recommends practices for producing homogeneous samples for circumstances when homogeneity testing is not possible.  
5.5 When the conditions of adequate within-sample homogeneity and between-sample homogeneity are satisfied, any differences in test results on multiple samples can reasonably be attributed to testing variation and not due to sample variation.  
5.6 When differences within or between samples are discovered and the samples are deemed insufficiently homogeneous, the sample preparation process can be improved or corrected and a new set of samples can be prepared. Or, in cases where the sample homogeneity cannot be improved or for other reasons when the samples must be used, the method of eval...
SCOPE
1.1 This guide presents techniques and guidance for evaluating and assuring homogeneity of individual samples and bulk materials used for interlaboratory and intra-laboratory studies.  
1.2 This guide is applicable to samples and reference materials used for proficiency testing programs and for interlaboratory studies to determine precision estimates for test methods. It may also be useful for activities related to quality control of testing within a single laboratory.  
1.3 Five techniques are presented for assessing sample homogeneity. The five techniques are not an exhaustive list of available techniques for assessing homogeneity of samples, but the techniques were chosen to cover a range of circumstances (and various degrees of rigor required) for laboratory studies of various types and purposes.  
1.4 Each of the first four techniques provides a scheme for testing for homogeneity and a statistical procedure for evaluating the results of the homogeneity testing. The circumstances are described for which each of the techniques is suited.  
1.5 For circumstances when homogeneity testing is not possible, the fifth technique provides guidance for producing homogeneous samples.  
1.6 The appendixes of this guide provide example spreadsheets for Techniques 1, 2, 3, and 4.  
1.7 This guide is not intended for evaluation of certified reference materials (CRMs) or materials used for calibration.  
1.8 Units—The system of units for this standard is not specified. Dimensional quantities in the standard are presented only as illustrations of calculation methods. The examples are not binding on products or test methods treated.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to ...

  • Guide
    32 pages
    English language
    sale 15% off
ASTM
ASTM E177-20(Practice)
Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods

ABSTRACT
The purpose of this practice is to present concepts necessary to the understanding of the terms “precision” and “bias” as used in quantitative test methods. This practice also describes methods of expressing precision and bias and, in a final section, gives examples of how statements on precision and bias may be written for ASTM test methods. A statement of precision allows potential users of a test method to assess in general terms the test method’s usefulness with respect to variability in proposed applications.
SIGNIFICANCE AND USE
4.1 Part A of the “Blue Book,” Form and Style for ASTM Standards, requires that all test methods include statements of precision and bias. This practice discusses these two concepts and provides guidance for their use in statements about test methods.  
4.2 Precision—A statement of precision allows potential users of a test method to assess in general terms the test method’s usefulness with respect to variability in proposed applications. A statement of precision is not intended to exhibit values that can be exactly duplicated in every user’s laboratory. Instead, the statement provides guidelines as to the magnitude of variability that can be expected between test results when the method is used in one, or in two or more, reasonably competent laboratories. For a discussion of precision, see 8.1.  
4.3 Bias—A statement of bias furnishes guidelines on the relationship between a set of typical test results produced by the test method under specific test conditions and a related set of accepted reference values (see 9.1).  
4.3.1 An alternative term for bias is trueness, which has a positive connotation, in that greater bias is associated with less favorable trueness. Trueness is the systematic component of accuracy.  
4.4 Accuracy—The term “accuracy,” used in earlier editions of Practice E177, embraces both precision and bias (see 9.3).
SCOPE
1.1 The purpose of this practice is to present concepts necessary to the understanding of the terms “precision” and “bias” as used in quantitative test methods. This practice also describes methods of expressing precision and bias and, in a final section, gives examples of how statements on precision and bias may be written for ASTM test methods.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM E2554-18e1(Practice)
Standard Practice for Estimating and Monitoring the Uncertainty of Test Results of a Test Method Using Control Chart Techniques

ABSTRACT
This practice describes techniques for a laboratory to estimate the uncertainty of a test result using data from test results on a control sample. This practice provides one method for a laboratory to estimate Measurement Uncertainty in accordance with Section A22.3 in Form and Style for ASTM Standards. This practice describes the use of control charts to evaluate the data obtained and presents a special type of control chart to monitor the estimate of uncertainty.
This practice provides one way for a laboratory to develop data-based Type A estimates of uncertainty as referred to in Section A22 in Form and Style for ASTM Standards.
SIGNIFICANCE AND USE
4.1 This practice provides one way for a laboratory to develop data-based Type A estimates of uncertainty as referred to in Section A22 in Form and Style for ASTM Standards.  
4.2 Laboratories accredited under ISO/IEC 17025 are required to present uncertainty estimates for their test results. This practice provides procedures that use test results to develop uncertainty estimates for an individual laboratory.  
4.3 Generally, these test results will be from a single sample of stable and homogeneous material known as a control or check sample.  
4.4 The true value of the characteristic(s) of the control sample being measured will ordinarily be unknown. However, this methodology may also be used if the control sample is a reference material, in which case the test method bias may also be estimated and incorporated into the uncertainty estimate. Many test methods do not have true reference materials available to provide traceable chains of uncertainty estimation.  
4.5 This practice also allows for ongoing monitoring of the laboratory uncertainty. As estimates of the level of uncertainty change, possibly as contributions to uncertainty are identified and minimized, revision to the laboratory uncertainty will be possible.
SCOPE
1.1 This practice describes techniques for a laboratory to estimate the uncertainty of a test result using data from test results on a control sample. This practice provides one method for a laboratory to estimate Measurement Uncertainty in accordance with Section A22.3 in Form and Style for ASTM Standards.  
1.2 Uncertainty as defined by this practice applies to the capabilities of a single laboratory. Any estimate of uncertainty determined through the use of this practice applies only to the individual laboratory for which the data are presented.  
1.3 The laboratory uses a well defined and established test method in determining a series of test results. The uncertainty estimated using this practice only applies when the same test method is followed. The uncertainty only applies for the material types represented by the control samples, and multiple control samples may be needed, especially if the method has different precision for different sample types or response levels.  
1.4 The uncertainty estimate determined by this practice represents the intermediate precision of test results. This estimate seeks to quantify the total variation expected within a single laboratory using a single established test method while incorporating as many known sources of variation as possible.  
1.5 This practice does not establish error estimates (error budget) attributed to individual factors that could influence uncertainty.  
1.6 This practice describes the use of control charts to evaluate the data obtained and presents a special type of control chart to monitor the estimate of uncertainty.  
1.7 The system of units for this standard is not specified. Dimensional quantities in the standard are presented only as illustrations of calculation methods. The examples are not binding on products or test methods treated.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmenta...

  • Standard
    8 pages
    English language
    sale 15% off