iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 969:1995

(Main)

Ductile iron pipes, fittings accessories and their joints for gas pipelines - Requirements and test methods

Ductile iron pipes, fittings accessories and their joints for gas pipelines - Requirements and test methods

This European Standard specifies the requirements and associated test methods applicable to ductile iron pipes, fittings, accessories and their joints for theconstruction of pipelines: - to convey air or combustible gases (e.g. natural gas or town gas) at pressures up to 16 bar; - to be installed below or above ground. Note 1: A combustible gas is a gas or any fuel that is in a gaseous state at a temperature of 15°C at a pressure of 1 bar.

Rohre, Formstücke, Zubehörteile aus duktilem Gußeisen und ihre Verbindungen für Gasleitungen - Anforderungen und Prüfverfahren

Diese europäische Norm legt die Anforderungen und die diesbezüglichen Prüfverfahren fest, die auf duktile Gußrohre, Formstücke, Zubehörteile und ihre Verbindungen anwendbar sind zur Errichtung von Rohrleitungen: - zum Transport von Luft oder brennbaren Gasen (z.B. Erdgas oder Stadtgas) bis zu einem Druck von 16 bar; -oberirdisch oder erdverlegt. Anmerkung 1: Ein brennbares Gas ist ein Gas oder ein beliebiger Brennstoff, der bei einer Temperatur von 15°C und einen Druck von 1 bar gasförmig ist.

Tuyaux, raccords et accessoires en fonte ductile et leurs assemblages pour canalisations de gaz - Prescriptions et méthodes d'essai

La présente norme européenne prescrit les exigences et les méthodes d'essai associées applicables aux tuyaux, raccords et accessoires en fonte ductile et à leurs assemblages, destinés à la construction de canalisations: - pour transporter de l'air ou des gaz combustibles (p.ex.: gaz naturel ou gaz de ville) à des pressions pouvant atteindre 16 bars; - installées dans le sol ou enaérien. Note 1: Un gaz combustible est un gaz ou tout combustible qui est à l'état gazeux à la température de 15°C et à la pression de 1 bar.

Cevi, fitingi in dodatki iz duktilne litine za plinovode - Zahteve in postopki preskušanja

General Information

Status
Withdrawn
Publication Date
22-Aug-1995
Withdrawal Date
17-Mar-2009
ICS
23.040.10 - Iron and steel pipes
23.040.40 - Metal fittings
Technical Committee
CEN/TC 203 - Cast iron pipes, fittings and their joints
Drafting Committee
CEN/TC 203/WG 5 - Materials, dimensions, common characteristics
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
18-Mar-2009
Completion Date
18-Mar-2009
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Ref Project
SIST EN 969:1998 - Ductile iron pipes, fittings accessories and their joints for gas pipelines - Requirements and test methods

Relations

Replaced By
EN 969:2009 - Ductile iron pipes, fittings, accessories and their joints for gas pipelines - Requirements and test methods
Effective Date
23-Mar-2009
Amended By
EN 969:1995/A1:1998 - Ductile iron pipes, fittings accessories and their joints for gas pipelines - Requirements and test methods
Effective Date
08-Jun-2022

Buy Standard

EN 969:1998EN 969:1998
PreviousNext
Standard
EN 969:1998
English language
61 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 969:1998
01-oktober-1998
Cevi, fitingi in dodatki iz duktilne litine za plinovode - Zahteve in postopki
preskušanja
Ductile iron pipes, fittings accessories and their joints for gas pipelines - Requirements
and test methods
Rohre, Formstücke, Zubehörteile aus duktilem Gußeisen und ihre Verbindungen für
Gasleitungen - Anforderungen und Prüfverfahren
Tuyaux, raccords et accessoires en fonte ductile et leurs assemblages pour
canalisations de gaz - Prescriptions et méthodes d'essai
Ta slovenski standard je istoveten z: EN 969:1995
ICS:
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
91.140.40 Sistemi za oskrbo s plinom Gas supply systems
SIST EN 969:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 969:1998

---------------------- Page: 2 ----------------------

SIST EN 969:1998

---------------------- Page: 3 ----------------------

SIST EN 969:1998

---------------------- Page: 4 ----------------------

SIST EN 969:1998

---------------------- Page: 5 ----------------------

SIST EN 969:1998

---------------------- Page: 6 ----------------------

SIST EN 969:1998

---------------------- Page: 7 ----------------------

SIST EN 969:1998

---------------------- Page: 8 ----------------------

SIST EN 969:1998

---------------------- Page: 9 ----------------------

SIST EN 969:1998

---------------------- Page: 10 ----------------------

SIST EN 969:1998

---------------------- Page: 11 ----------------------

SIST EN 969:1998

---------------------- Page: 12 ----------------------

SIST EN 969:1998

---------------------- Page: 13 ----------------------

SIST EN 969:1998

---------------------- Page: 14 ----------------------

SIST EN 969:1998

---------------------- Page: 15 ----------------------

SIST EN 969:1998

---------------------- Page: 16 ----------------------

SIST EN 969:1998

---------------------- Page: 17 ----------------------

SIST EN 969:1998

---------------------- Page: 18 ----------------------

SIST EN 969:1998

---------------------- Page: 19 ----------------------

SIST EN 969:1998

---------------------- Page: 20 ----------------------

SIST EN 969:1998

---------------------- Page: 21 ----------------------

SIST EN 969:1998

---------------------- Page: 22 ----------------------

SIST EN 969:1998

---------------------- Page: 23 ----------------------

SIST EN 969:1998

---------------------- Page: 24 ----------------------

SIST EN 969:1998

---------------------- Page: 25 ----------------------

SIST EN 969:1998

---------------------- Page: 26 ----------------------

SIST EN 969:199
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 15655-2:2020(Main)
Ductile iron pipes, fittings and accessories - Requirements and test methods for organic linings of ductile iron pipes and fittings - Part 2: Thermoplastic Acid Modified Polyolefin (TMPO) lining of pipes
SIST EN 15655-2:2021

This document specifies the requirements and test methods applicable to factory applied internal lining made of thermoplastic acid modified polyolefin (TMPO) for the heavy duty corrosion protection of ductile iron pipes conforming to EN 545, EN 598 and EN 969. This document also applies to pipes with only socket and spigot ends coated with TMPO. Fittings and accessories are covered separately by EN 14901-2.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14628-1:2020(Main)
Ductile iron pipes, fittings and accessories - Requirements and test methods - Part 1: PE coatings
SIST EN 14628-1:2020

This document specifies the requirements and test methods applicable to factory applied extruded polyethylene coatings for the external corrosion protection of ductile iron pipes according to EN 545, EN 598 and EN 969 for use at operating temperatures up to 50 °C.
This document is not applicable to ductile iron pipes protected with thin PE sleeve. Special works at site like drilling, tapping, etc. can influence the corrosion protection properties. Those job steps are intended to be included in the instructions of pipe saddle and accessory manufacturers and all other essential installation instructions. These instructions are not part of this document.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14901-2:2019(Main)
Ductile iron pipes, fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 2: Thermoplastic acid modified polyolefin coating (TMPO)
SIST EN 14901-2:2020

This document defines the requirements and test methods for factory applied thermoplastic acid modified polyolefin (TMPO) coatings used for the protection of ductile iron fittings and accessories according to EN 545, EN 598, EN 969, EN 12842 and EN 14525:
-   conveying water (e.g. potable water, raw water, …) at operating temperature up to 50 °C; or
-   conveying waste water at operating temperature up to 45 °C; or
-   conveying gas at operating temperature up to 50 °C;
-   suitable for external environments, i.e. soils, waters and atmospheres of all common corrosion loads, characterized in D.2.3 of EN 545:2010.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14901-1:2014+A1:2019(Main + Amendment)
Ductile iron pipes, fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 1: Epoxy coating (heavy duty)
SIST EN 14901-1:2014+A1:2020

This European Standard defines the requirements and test methods for factory applied epoxy coatings (fusion bonded powder or liquid two-pack) used for the corrosion protection of ductile iron fittings and accessories conforming to EN 545, EN 598, EN 969, EN 12842, EN 14525, for:
-   conveying water (e.g. potable water) at operating temperature up to 50 °C excluding frost; or
-   conveying waste water at operating temperature up to 45 °C excluding frost; or
-   conveying gas at operating temperature up to 50 °C;
-   suitable for external environments, i.e. soils, waters and atmospheres of all common corrosion loads, characterized in EN 545:2010, D.2.3.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15655-1:2018(Main)
Ductile iron pipes, fittings and accessories - Requirements and test methods for organic linings of ductile iron pipes and fittings - Part 1: Polyurethane lining of pipes and fittings
SIST EN 15655-1:2019

This European Standard defines the requirements and test methods applicable to factory applied internal polyurethane high duty corrosion protection of buried ductile iron pipes and fittings conforming to EN 545, EN 598 and EN 969 for use at permanent operating temperatures up to 45 °C

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 16950:2016(Main)
Ductile iron pipes, fittings and accessories - Sanitary characteristics and test methods
SIST-TP CEN/TR 16950:2017

This Technical Report contains the sanitary characteristics and test methods applicable to those factory applied lining, coating and jointing materials of ductile iron pipes and fittings conforming to EN 545 which are in contact with water intended for human consumption for use at operating temperatures up to 50 °C. Ductile cast iron itself is not in direct contact with the conveyed water therefore no characteristics in respect to the sanitary behaviour are necessary. As ductile cast iron is impermeable against diffusion of organic substances the water quality is maintained in service. Different surface/volume ratios are used in the tests for pipes, fittings and joints to reflect the different impact of their surface areas exposed to the water in the overall pipeline.

  • Technical report
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 16470:2013(Main)
Environmental aspects of ductile iron pipe systems for water and sewerage applications
SIST-TP CEN/TR 16470:2013

This Technical Report applies to all water and sewerage applications of ductile iron pipe systems and provides a structure on how to identify and consider environmental aspects and potential environmental impacts of ductile iron pipe systems throughout their life cycle.
This Technical Report gives guidance on how the life cycle of ductile iron pipelines should be considered in accordance with EN ISO 14044. This Technical Report also includes health and safety aspects related to the production, use and recycling of ductile iron pipe systems.

  • Technical report
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 545:2010(Main)
Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
SIST EN 545:2011

This European Standard specifies the requirements and associated test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of pipelines outside buildings:
-   to convey different types of water (e.g. raw water, treated water, re-used water) for all types of applications (e.g. water intended for human consumption, for fire protection, for snow making, for irrigation, for hydro-electricity etc.);
-   with or without pressure;
-   to be installed below or above ground.
This European Standard is applicable to pipes, fittings and accessories which are:
-   manufactured with socketed, flanged or spigot ends;
-   supplied externally and internally coated;
-               suitable for fluid temperatures between 0 °C and 50 °C, excluding frost;
-   not intended for use in areas subject to fire regulations.
NOTE 1   This does not preclude special arrangements for the products to be used at higher temperatures.
This European Standard covers pipes and fittings cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints and accessories, in a size range extending from DN 40 to DN 2 000, inclusive.
This European Standard specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all components including joints. Joint design and gasket shapes are outside the scope of this standard.
In addition, reference is made to the performance requirements of couplings, flange adaptors and saddles manufactured for use with ductile iron pipes and fittings.
NOTE 2   In this European Standard, all pressures are relative pressures, expressed in bars (100 kPa = 1 bar).

  • Standard
    93 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard + National Annex and/or Foreword
    96 pages
    Foreword and/or annex in Slovenian language, body of the standard in English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 16017:2010(Main)
Guide to the use of EN 598
SIST-TP CEN/TR 16017:2010

EN 598 specifies the requirements and associated test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of drains and sewers outside buildings:
-   operating without pressure (gravity sewerage), or with positive or negative pressure;
-   to be installed below or above ground;
-   to convey surface water, domestic waste water and certain types of industrial effluents, either in separate systems or in combined systems.
This technical report:
-   explains in more detail the process of testing for the performance tests;
-   explains in more detail the benefits of high alumina cement lining;
-   explains in more detail the definitions of the different types/levels of attestation to enable customers to ensure their requirements are fulfilled;
-   explains in more detail the ways of certification of conformity with EN 598 for a reliable evaluation of the performance of products;
-   explains in more detail CE marking and its relevance i.e. the CE mark is not a mark of conformity with a standard but only a self-declaration concerning the CPD essential requirements.
In order to make the use of this Technical Report easier, the clauses of this document refer to the corresponding clause numbers in EN 598.

  • Technical report
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 969:2009(Main)
Ductile iron pipes, fittings, accessories and their joints for gas pipelines - Requirements and test methods
SIST EN 969:2009

This European Standard specifies the requirements and associated test methods applicable to ductile iron pipes, fittings, accessories and their joints used for the construction of external pipelines:
-   to convey air or combustible gases (e.g. natural gas or town gas) at pressures up to 16 bar;
-   to be installed below or above ground.
NOTE 1   A combustible gas is a gas or any fuel that is in gaseous state at a temperature of 15 °C at a pressure of 1 bar.
This European Standard applies to pipes, fittings and accessories which are:
-   manufactured with socketed, flanged or spigot ends;
-   normally delivered externally and internally coated;
-   suitable for gas temperatures between - 15 °C and 50 °C.
This European Standard covers pipes, fittings and accessories cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints, in a size range extending from DN 40 to DN 600 inclusive.
This European Standard specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all components including joints. Joint design and gasket shape are outside the scope of this European Standard.
NOTE 2   In this European Standard, all pressures are relative pressures expressed in bars (100 kPa = 1 bar).

  • Standard
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day