iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 5832-2:2018

(Main)

Implants for surgery - Metallic materials - Part 2: Unalloyed titanium (ISO 5832-2:2018)

Implants for surgery - Metallic materials - Part 2: Unalloyed titanium (ISO 5832-2:2018)

ISO 5832-2:2018 specifies the characteristics of, and corresponding test methods for, unalloyed titanium for use in the manufacture of surgical implants.
Six grades of titanium based on tensile strength are listed in Table 2.
NOTE      The mechanical properties of a sample obtained from a finished product made of this metal do not necessarily comply with those specified in ISO 5832-2:2018.

Chirurgische Implantate - Metallische Werkstoffe - Teil 2: Unlegiertes Titan (ISO 5832-2:2018)

Dieser Teil von ISO 5832 beschreibt die Eigenschaften und die dazugehörige Prüfverfahren für unlegiertes Titan, das zur Herstellung von chirurgischen Implantaten verwendet wird.
Es werden Festlegungen für sechs verschiedene Titan-Güten auf der Basis der Zugfestigkeit getroffen (siehe Tabelle 2).
ANMERKUNG Die mechanischen Eigenschaften einer Probe, die von einem Fertigprodukt aus diesem Metall werden, müssen nicht notwendigerweise mit den Angaben in diesem Teil von ISO 5832 übereinstimmen.

Implants chirurgicaux - Produits à base de métaux - Partie 2: Titane non allié (ISO 5832-2:2018)

L'ISO 5832-2:2018 spécifie les caractéristiques du titane non allié utilisé pour la fabrication des implants chirurgicaux et les méthodes d'essai correspondantes.
Le Tableau 2 répertorie six nuances de titane fondées sur la résistance à la traction.
NOTE       Les caractéristiques mécaniques d'un échantillon prélevé sur un produit fini fabriqué avec ce métal ne sont pas nécessairement conformes aux valeurs spécifiées dans l'ISO 5832-2:2018.

Vsadki (implantati) za kirurgijo - Kovinski materiali - 2. del: Nelegirani titan (ISO 5832-2:2018)

Ta dokument določa lastnosti in zadevne preskusne metode za nelegirani titan, ki se uporablja pri izdelavi vsadkov za kirurgijo.
V preglednici 2 je navedenih šest stopenj natezne trdnosti titana.
OPOMBA: mehanske lastnosti vzorca končnega izdelka iz te kovine niso nujno v skladu z lastnostmi, ki so določene v tem dokumentu.

General Information

Status
Published
Publication Date
01-May-2018
Withdrawal Date
29-Nov-2018
ICS
11.040.40 - Implants for surgery, prosthetics and orthotics
Technical Committee
CEN/TC 55 - Dentistry
Drafting Committee
CEN/TC 55 - Dentistry
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
02-May-2018
Completion Date
02-May-2018
Directive
93/42/EEC - Council Directive 93/42/EEC of 14 June 1993 concerning medical devices
Ref Project
SIST EN ISO 5832-2:2018 - Implants for surgery - Metallic materials - Part 2: Unalloyed titanium (ISO 5832-2:2018)

Relations

Replaces
EN ISO 5832-2:2012 - Implants for surgery - Metallic materials - Part 2: Unalloyed titanium (ISO 5832-2:1999)
Effective Date
04-May-2016

Buy Standard

EN ISO 5832-2:2018EN ISO 5832-2:2018
PreviousNext
Standard
EN ISO 5832-2:2018
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 5832-2:2018
01-julij-2018
1DGRPHãþD
SIST EN ISO 5832-2:2012
Vsadki (implantati) za kirurgijo - Kovinski materiali - 2. del: Nelegirani titan (ISO
5832-2:2018)
Implants for surgery - Metallic materials - Part 2: Unalloyed titanium (ISO 5832-2:2018)
Chirurgische Implantate - Metallische Werkstoffe - Teil 2: Unlegiertes Titan (ISO 5832-
2:2018)
Implants chirurgicaux - Produits à base de métaux - Partie 2: Titane non allié (ISO 5832-
2:2018)
Ta slovenski standard je istoveten z: EN ISO 5832-2:2018
ICS:
11.040.40 Implantanti za kirurgijo, Implants for surgery,
protetiko in ortetiko prosthetics and orthotics
SIST EN ISO 5832-2:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 5832-2:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 5832-2:2018


EN ISO 5832-2
EUROPEAN STANDARD

NORME EUROPÉENNE

May 2018
EUROPÄISCHE NORM
ICS 11.040.40 Supersedes EN ISO 5832-2:2012
English Version

Implants for surgery - Metallic materials - Part 2:
Unalloyed titanium (ISO 5832-2:2018)
Implants chirurgicaux - Produits à base de métaux - Chirurgische Implantate - Metallische Werkstoffe - Teil
Partie 2: Titane non allié (ISO 5832-2:2018) 2: Unlegiertes Titan (ISO 5832-2:2018)
This European Standard was approved by CEN on 1 March 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5832-2:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 5832-2:2018
EN ISO 5832-2:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 5832-2:2018
EN ISO 5832-2:2018 (E)
European foreword
This document (EN ISO 5832-2:2018) has been prepared by Technical Committee ISO/TC 150
"Implants for surgery" in collaboration with Technical Committee CEN/TC 55 “Dentistry” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2018, and conflicting national standards
shall be withdrawn at the latest by November 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 5832-2:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 5832-2:2018 has been approved by CEN as EN ISO 5832-2:2018 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 5832-2:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 5832-2:2018
INTERNATIONAL ISO
STANDARD 5832-2
Fourth edition
2018-03
Implants for surgery — Metallic
materials —
Part 2:
Unalloyed titanium
Implants chirurgicaux —
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 5832-3:2021(Main)
Implants for surgery - Metallic materials - Part 3: Wrought titanium 6-aluminium 4-vanadium alloy (ISO 5832-3:2021)
SIST EN ISO 5832-3:2022

This document specifies the characteristics of, and corresponding test methods for, the wrought titanium alloy known as titanium 6-aluminium 4-vanadium alloy (Ti-6Al-4V alloy) for use in the manufacture of surgical implants.
NOTE      The mechanical properties of a sample obtained from a finished product made of this alloy might not necessarily comply with the specifications given in this document.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13356:2015(Main)
Implants for surgery - Ceramic materials based on yttria-stabilized tetragonal zirconia (Y-TZP) (ISO 13356:2015)
SIST EN ISO 13356:2015

ISO 13356:2015 specifies the requirements and corresponding test methods for a biocompatible and biostable ceramic bone-substitute material based on yttria-stabilized tetragonal zirconia (yttria tetragonal zirconia polycrystal, Y-TZP) for use as a material for surgical implants.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12417-1:2024(Main)
Cardiovascular implants and extracorporeal systems - Vascular device-drug combination products - Part 1: General requirements (ISO 12417-1:2024)
SIST EN ISO 12417-1:2024

This document specifies requirements for vascular device-drug combination products (VDDCPs).
With regard to safety, this document outlines requirements for intended performance, design attributes, materials, design evaluation, manufacturing, sterilization, packaging and information supplied by the manufacturer.
For implanted products, this document is intended to be used as a supplement to ISO 14630, which specifies general requirements for the performance of non-active surgical implants. This document is intended to be used as a supplement to relevant device-specific standards, such as the ISO 25539 series specifying requirements for endovascular devices. Requirements listed in this document also address VDDCPs that are not permanent implants.
NOTE 1        Due to variations in the design of combination products covered by this document and due to the relatively recent development of some of these combination products, acceptable standardized in vitro test results and clinical study results are not always available. As further scientific and clinical data become available, appropriate revision of this document can be necessary.
This document applies to delivery systems or parts of the delivery system that are an integral component of the vascular device and that are drug-covered (e.g. drug-covered balloon catheters and drug-covered guidewires).
This document does not apply to devices whose PMOA provide a conduit for delivery of a drug (e.g. infusion catheters), unless they contain a drug component that is intended to have an ancillary action to the device part (e.g. antimicrobial coated infusion catheter).
This document does not apply to procedures and devices used prior to and following the introduction of the VDDCP (e.g. balloon angioplasty devices) that do not affect the drug-related aspects of the device.
This document does not provide a comprehensive pharmacological evaluation of VDDCPs.
NOTE 2        Some information about the requirements of certain national and regional authorities is given in Annex B.
The connection of absorbable components of VDDCPs (e.g. coatings) with drug-related aspects of the device are addressed in this document. This document does not provide an exhaustive list of the degradation and other time-dependent aspects of absorbable implants and coatings.
NOTE 3        For more information on absorbable coatings, refer to ISO/TS 17137 and ASTM F3036-13.
This document does not address issues associated with viable or non-viable biological materials such as tissues, cells or proteins.
This document does not address issues associated with active surgical implants (i.e. implants that require power not generated by the human body or gravity).

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21917:2022(Main)
Anaesthetic and respiratory equipment - Voice prostheses (ISO 21917:2021)
SIST EN ISO 21917:2023

This document specifies performance requirements for voice prostheses including requirements for marking, packaging and information to be provided by the manufacturer as well as test methods for the evaluation of physical characteristics of voice prostheses.
NOTE      There is guidance or rationale for this list item contained in A.2.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14708-4:2022(Main)
Implants for surgery - Active implantable medical devices - Part 4: Implantable infusion pump systems (ISO 14708-4:2022)
SIST EN ISO 14708-4:2022

This document specifies particular requirements for active implantable medical devices intended to deliver a medicinal substance to site-specific locations within the human body, to provide basic assurance of safety for both patients and users. It amends and supplements ISO 14708-1:2014. The requirements of this document take priority over those of ISO 14708-1.
This document is applicable to active implantable medical devices intended to deliver medicinal substances to site-specific locations within the human body.
This document is also applicable to some non-implantable parts and accessories of the devices defined in Clause 3.
The tests that are specified in this document are type tests intended to be carried out on a sample of a device to show compliance and are not intended to be used for the routine testing of manufactured products.
NOTE       This document is not intended to apply to non-implantable infusion systems.

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14708-3:2022(Main)
Implants for surgery - Active implantable medical devices - Part 3: Implantable neurostimulators (ISO 14708-3:2017)
SIST EN ISO 14708-3:2023

ISO 14708-3:2017 is applicable to active implantable medical devices intended for electrical stimulation of the central or peripheral nervous system.
The tests that are specified in this document are type tests and are to be carried out on a sample of a device to assess device behavioural responses, and are not intended to be used for the routine testing of manufactured products.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14708-2:2022(Main)
Implants for surgery - Active implantable medical devices - Part 2: Cardiac pacemakers (ISO 14708-2:2019)
SIST EN ISO 14708-2:2022

This document specifies requirements that are applicable to those active implantable medical devices intended to treat bradyarrhythmias and devices that provide therapies for cardiac resynchronization.
The tests that are specified in this document are type tests, and are to be carried out on samples of a device to show compliance.
This document was designed for bradyarrhythmia pulse generators used with endocardial leads or epicardial leads. At the time of this edition, the authors recognized the emergence of leadless technologies for which adaptations of this part will be required. Such adaptations are left to the discretion of manufacturers incorporating these technologies.
This document is also applicable to some non-implantable parts and accessories of the devices (see Note 1).
The electrical characteristics of the implantable pulse generator or lead are determined either by the appropriate method detailed in this particular standard or by any other method demonstrated to have an accuracy equal to, or better than, the method specified. In case of dispute, the method detailed in this particular standard applies.
Any features of an active implantable medical device intended to treat tachyarrhythmias are covered by ISO 14708-6.
NOTE 1    The device that is commonly referred to as an active implantable medical device can in fact be a single device, a combination of devices, or a combination of a device or devices and one or more accessories. Not all of these parts are required to be either partially or totally implantable, but there is a need to specify some requirements of non-implantable parts and accessories if they could affect the safety or performance of the implantable device.
NOTE 2    In this document, terms printed in italics are used as defined in Clause 3. Where a defined term is used as a qualifier in another term, it is not printed in italics unless the concept thus qualified is also defined.

  • Standard
    80 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14708-6:2022(Main)
Implants for surgery - Active implantable medical devices - Part 6: Particular requirements for active implantable medical devices intended to treat tachyarrhythmia (including implantable defibrillators) (ISO 14708-6:2019)
SIST EN ISO 14708-6:2022

This document specifies requirements that are applicable to implantable cardioverter defibrillators and CRT-Ds and the functions of active implantable medical devices intended to treat tachyarrhythmia.
The tests that are specified in ISO 14708 are type tests and are to be carried out on samples of a device to show compliance.
This document was designed for tachyarrhythmia pulse generators used with either endocardial leads or epicardial leads. At the time of this edition, the authors recognized the emergence of technologies that do not use endocardial or epicardial leads for which adaptations of this part will be required. Such adaptations are left to the discretion of manufacturers incorporating these technologies.
This document is also applicable to some non-implantable parts and accessories of the devices (see Note 1).
The characteristics of the implantable pulse generator or lead shall be determined by either the appropriate method detailed in this document or by any other method demonstrated to have accuracy equal to, or better than, the method specified. In the case of dispute, the method detailed in this document shall apply.
Any aspect of an active implantable medical device intended to treat bradyarrhythmias or cardiac resynchronization is covered by ISO 14708-2.
NOTE 1    The device that is commonly referred to as an active implantable medical device can in fact be a single device, a combination of devices, or a combination of a device or devices and one or more accessories. Not all of these parts are required to be either partially or totally implantable, but there is a need to specify some requirements of non-implantable parts and accessories if they could affect the safety or performance of the implantable device.
NOTE 2    In this document, terms printed in italics are used as defined in Clause 3.  Where a defined term is used as a qualifier in another term, it is not printed in italics unless the concept thus qualified is also defined.

  • Standard
    75 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14708-7:2022(Main)
Implants for surgery - Active implantable medical devices - Part 7: Particular requirements for cochlear and auditory brainstem implant systems (ISO 14708-7:2019)
SIST EN ISO 14708-7:2022

This document specifies requirements that are applicable to those active implantable medical devices that are intended to treat hearing impairment via electrical stimulation of the auditory pathways. Devices which treat hearing impairment via means other than electrical stimulation are not covered by this document.
The tests that are specified in this document are type tests and are to be carried out on samples of a device to show compliance.
This document is also applicable to non-implantable parts and accessories of the devices (see NOTE).
The electrical characteristics of the implantable part are determined by either the appropriate method detailed in this document or by any other method demonstrated to have an accuracy equal to, or better than, the method specified. In the case of dispute, the method detailed in this document applies.
NOTE       A device that is commonly referred to as an active implantable medical device can in fact be a single device, a combination of devices, or a combination of a device or devices and one or more accessories. Not all of these parts are required to be either partially or totally implantable, this document specifies those requirements of non-implantable parts and accessories which could affect the safety or performance of the implantable part.

  • Standard
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14708-5:2022(Main)
Implants for surgery - Active implantable medical devices - Part 5: Circulatory support devices (ISO 14708-5:2020)
SIST EN ISO 14708-5:2022

This document specifies requirements for safety and performance of active implantable circulatory support devices, including type tests, animal studies and clinical evaluation requirements.
NOTE    The device that is commonly referred to as an active implantable medical device can in fact be a single device, a combination of devices, or a combination of a device or devices and one or more accessories. Not all of these parts are required to be either partially or totally implantable, but there is a need to specify main requirements of non-implantable parts and accessories if they could affect the safety or performance of the implantable device.
The tests that are specified in this document are type tests and are to be carried out on a sample of a device to assess device behavioural responses and are not intended to be used for the routine testing of manufactured products.
Included in the scope of this document are:
—     ventricular assist devices (VAD), left or right heart support;
—     total artificial hearts (TAH);
—     biventricular assist devices (biVAD);
—     percutaneous assist devices;
—     paediatric assist devices.

  • Standard
    79 pages
    English language
    sale 10% off
    e-Library read for
    1 day