EN 1994-2:2005

Eurocode 4 - Design of composite steen and concrete structures - Part 2: General rules and rules for bridges

(1) Part 2 of Eurocode 4 gives design rules for steel-concrete composite bridges or members of bridges, additional to the general rules in EN 1994-1-1. Cable stayed bridges are not fully covered by this part.
(2) The following subjects are dealt with in Part 2:
Section 1:   General
Section 2:   Basis of design
Section 3:   Materials
Section 4:   Durability
Section 5:   Structural analysis
Section 6:   Ultimate limit states
Section 7:   Serviceability limit states
Section 8:   Decks with precast concrete slabs
Section 9:   Composite plates in bridges
(3) Provisions for shear connectors are given only for welded headed studs.
NOTE: Reference to guidance for other types as shear connectors may be given in the National Annex.

Eurocode 4 : Bemessung und Konstruktion von Verbundtragwerken aus Stahl und Beton - Teil 2: Allgemeine Bemessungsregeln und Anwendungsregeln für Brücken

(1) Der Teil 2 des Eurocode 4 enthält zusätzlich zu den in EN 1994-1-1 angegebenen allgemeinen Bemessungsregeln ergänzende Bemessungsregeln für Verbundbrücken und Verbundbauteile in Brückentragwerken. Schrägseilbrücken werden nicht vollständig behandelt.
(2) Der Teil 2 enthält die folgenden Abschnitte:- Chapter 1   :   Introduction
   - Chapter 2   :   Basis of design
   - Chapter 3   :   Materials
   - Chapter 4   :   Ultimate limit states
   - Chapter 5   :   Serviceability limit states
   - Chapter 6   :   Shear connection in beams for buildings
   - Chapter 7   :   Composite slabs with profiled steel sheeting for buildings
   - Chapter 8   :   Floors with precast concrete slabs for buildings
   - Chapter 9   :   Execution
   - Chapter 10   :   Design assisted by testing
   - Annex A   :   Reference documents   (Normative)
   - Annex B   :   Lateral-torsional buckling   (Normative)
   - Annex C   :   Resistance of doubly symmetric composite cross   (Normative)
sections in combined compression and bending
   - Annex D   :   Composite columns with mono-symmetrical cross   (Normative)
section
   - Annex E   :   Partial shear connection method for composite slabs   (Normative)
   - Annex F   :   Checklist of the information required in test reports   (Informative)
1    Allgemeines
2    Grundlagen der Tragwerksplanung
3    Werkstoffe
4    Dauerhaftigkeit
5    Tragwerksberechnung
6    Grenzzustände der Tragfähigkeit
7    Grenzzustände der Gebrauchstauglichkeit
8    Fahrbahnplatten aus Fertigteilen
9    Fahrbahnplatten in Verbundbauweise
(3) Für die Verbundsicherung werden ausschließlich Regelungen für Kopfbolzendübel angegeben.
ANMERKUNG: Regelungen für andere Verbundmittel dürfen einem Nationalen Anhang entnommen werden.

Eurocode 4 - Calcul des structures mixtes acier-béton - Partie 2: Règles générales et règles pour les ponts

Les États Membres de l'UE et de l'AELE reconnaissent que les Eurocodes servent de documents de référence pour les usages suivants :
-   comme moyen de prouver la conformité des bâtiments et des ouvrages de génie civil aux exigences essentielles de la Directive du Conseil 89/106/CEE, en particulier à l'Exigence Essentielle N°1 – Stabilité et résistance mécanique – et à l'Exigence Essentielle N°2 – Sécurité en cas d'incendie ;
-   comme base de spécification des contrats pour les travaux de construction et les services techniques associés ;
-   comme cadre d'établissement de spécifications techniques harmonisées pour les produits de construction (EN et ATE).
   Les Eurocodes, dans la mesure où ils concernent les ouvrages eux-mêmes, ont une relation directe avec les Documents Interprétatifs ) visés à l'Article 12 de la DPC, bien qu'ils soient d'une nature différente de celle des normes harmonisées de produits ). En conséquence, les aspects techniques résultant des travaux effectués pour les Eurocodes nécessitent d'être pris en considération de façon adéquate par les Comités techniques du CEN et/ou les groupes de travail de l'EOTA travaillant sur les normes de produits en vue de parvenir à une complète compatibilité de ces spécifications techniques avec les Eurocodes.
Les normes Eurocodes fournissent des règles de conception structurale communes d'usage quotidien pour le calcul des structures entières et des produits composants de nature traditionnelle ou innovante. Les formes de construction ou les conceptions inhabituelles ne sont pas spécifiquement couvertes, et il appartiendra en ces cas au concepteur de se procurer des bases spécialisées supplémentaires.

Evrokod 4: Projektiranje sovprežnih konstrukcij iz jekla in betona – 2. del: Splošna pravila in pravila za mostove

General Information

• Status: Published
• Publication Date: 11-Oct-2005
• Withdrawal Date: 30-Mar-2010
• ICS: 91.010.30 - Technical aspects
• ICS: 91.080.10 - Metal structures
• ICS: 91.080.13 - Steel structures
• ICS: 91.080.40 - Concrete structures
• ICS: 93.040 - Bridge construction
• Technical Committee: CEN/TC 250 - Structural Eurocodes
• Drafting Committee: CEN/TC 250/SC 4 - Eurocode 4: Design of composite steel and concrete structures
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 12-Oct-2005
• Completion Date: 12-Oct-2005
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/265 - Mandate to CEN for the conversion of the Eurocodes from ENV into EN concerning the structural and geotechnical design of buildings and civil engineering works
• Mandate: M/BC/CEN/89/11 - Framework mandate to CEN on Eurocode work : execution of a standardization programme on Eurocodes for the structural design of building and civil engineering works
• Ref Project: SIST EN 1994-2:2005 - Eurocode 4 - Design of composite steen and concrete structures - Part 2: General rules and rules for bridges

Relations

• Replaces: ENV 1994-2:1997 - Eurocode 4: Design of composite steel and concrete structures - Part 2: Composite bridges
• Effective Date: 22-Dec-2008
• Corrected By: EN 1994-2:2005/AC:2008 - Eurocode 4 - Design of composite steel and concrete structures - Part 2: General rules and rules for bridges
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Eurocode 4 - Design of composite steen and concrete structures - Part 2: General rules and rules for bridgesEvrokod 4: Projektiranje sovprežnih konstrukcij iz jekla in betona – 2. del: Splošna pravila in pravila za mostoveEurocode 4 - Calcul des structures mixtes acier-béton - Partie 2: Regles générales et regles pour les pontsEurocode 4 : Bemessung und Konstruktion von Verbundtragwerken aus Stahl und Beton - Teil 2: Allgemeine Bemessungsregeln und Anwendungsregeln für BrückenTa slovenski standard je istoveten z:EN 1994-2:2005SIST EN 1994-2:2005en91.080.40Betonske konstrukcijeConcrete structures93.040Gradnja mostovBridge construction91.010.30Technical aspects91.080.10Kovinske konstrukcijeMetal structuresICS:SIST ENV 1994-2:20041DGRPHãþDSLOVENSKI
STANDARDSIST EN 1994-2:200501-december-2005







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1994-2October 2005ICS 91.010.30; 91.080.10; 91.080.40; 93.040Supersedes ENV 1994-2:1997
English VersionEurocode 4 - Design of composite steen and concrete structures- Part 2: General rules and rules for bridgesEurocode 4 - Calcul des structures mixtes acier-béton -Partie 2: Règles générales et règles pour les pontsEurocode 4 - Bemessung und konstruktion vonVerbundtragwerken aus Stahl und Beton - Teil 2:Allgemeine Bemessungsregeln und Anwendungsregeln fürBrückenThis European Standard was approved by CEN on 7 July 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1994-2:2005: E



EN 1994-2: 2005 (E)
2Contents
Page
Foreword…………………………………………………………………………………………. 7 Section 1 General……………………………………………………………………………… 11 1.1 Scope………………………………………………………………………………………… 11
1.1.1 Scope of Eurocode 4…………………………………………………………………. 11
1.1.2 Scope of Part 1-1 of Eurocode 4………………………………………………………. 11
1.1.3 Scope of Part 2 of Eurocode 4………………………………………………………… 12 1.2 Normative references………………………………………………………………………. 12
1.2.1 General reference standards…………………………………………………………… 12
1.2.2 Other reference standards………………………………………………………………12
1.2.3 Additional general and other reference standards for composite bridges ……………. 13 1.3 Assumptions………………………………………………………………………………… 13 1.4 Distinction between principles and application rules………………………………………. 14 1.5 Definitions……………………………………………………………………………………14
1.5.1 General………………………………………………………………………………… 14
1.5.2 Additional terms and definitions used in this Standard………………………………. 14
1.5.2.1
Composite member…………………………………………………………. 14
1.5.2.2
Shear connection……………………………………………………………. 14
1.5.2.3
Composite behaviour………………………………………………………… 14
1.5.2.4
Composite beam………………………………………………………………14
1.5.2.5
Composite column…………………………………………………………….14
1.5.2.6
Composite slab………………………………………………………………. 14
1.5.2.7
Composite frame…………………………………………………………… 14
1.5.2.8
Composite joint……………………………………………………………… 15
1.5.2.9
Propped structure or member………………………………………………… 15
1.5.2.10 Un-propped structure or member……………………………………………. 15
1.5.2.11 Un-cracked flexural stiffness………………………………………………… 15
1.5.2.12 Cracked flexural stiffness…………………………………………………… 15
1.5.2.13 Prestress……………………………………………………………………… 15
1.5.2.14 Filler beam deck……………………………………………………………… 15
1.5.2.15 Composite plate……………………………………………………………… 15 1.6 Symbols …………….……………………………………………………………………… 15
Section 2 Basis of design………………………………………………………………………. 22 2.1 Requirements………………………………………………………………………………. 22 2.2 Principles of limit states design……………………………………………………………. 22 2.3 Basic variables………………………………………………………………………………. 22
2.3.1 Actions and environmental influences………………………………………………… 22
2.3.2 Material and product properties………………………………………………………. 22
2.3.3 Classification of actions………………………………………………………………. 22 2.4 Verification by the partial factor method……………………………………………
...