EN 17082:2019
(Main)Domestic and non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW
Domestic and non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW
This document specifies the requirements and test methods for the safety and efficiency of gas fired air heaters with or without a fan to assist the transportation of combustion air and/or flue gases, hereafter referred to as "appliances".
This standard also applies to warm air heaters having forced draught burners.
This European Standard applies to Type A2, A3 appliances, with an input not exceeding 300 kW (net CV basis), intended for non-domestic use.
This European Standard also applies to Type B11, B11AS, B11BS, B12, B12AS, B12BS, B13, B13AS, B13BS, B14, B14AS, B14BS, B22, B23, B41, B41AS, B41BS, B42, B42AS, B42BS, B43, B43AS, B43BS, B44, B44AS, B44BS, B52, B53, C11, C12, C13, C21, C31, C32, C33, C41, C62 and C63 appliances with an input not exceeding 300 kW (net CV basis), intended for domestic and non-domestic use.
Provision of the heated air may be by means of ducting.
This European Standard does not apply to:
a) dual purpose air conditioning appliances (heating and cooling);
b) appliances where the air is heated by an intermediate fluid;
c) portable or transportable forced convection appliances;
d) appliances fitted with manual or automatic means of adjusting the combustion products evacuation by means of flue dampers;
e) appliances having multiple heating units with a single draught diverter;
f) appliances fitted with more than one flue outlet;
g) appliances fitted with gas boosters;
h) C21 and C41 appliances for 3rd family gases.
NOTE For C41 appliances, see all requirements and test methods that are valid for C21 appliances, unless otherwise stated.
This European Standard is not intended to cover appliances projected for connection to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance.
This European Standard is applicable to appliances which are intended to be type tested.
Häusliche und nicht-häusliche gasbefeuerte Warmlufterzeuger mit erzwungener Konvektion zur Raumbeheizung, deren Nennwärmebelastung 300 kW nicht übersteigt
Dieses Dokument legt die Anforderungen und Prüfverfahren für die Sicherheit und den Wirkungsgrad von gasbefeuerten Warmlufterzeugern mit oder ohne Gebläse zur Unterstützung des Transports von Verbrennungsluft und/oder Abgasen fest, die im weiteren Verlauf als „Geräte“ bezeichnet werden.
Dieses Dokument ist darüber hinaus auch auf Warmlufterzeuger mit Gebläsebrennern anwendbar.
Dieses Dokument gilt für Geräte des Typs A2 und A3 mit einer Leistungsaufnahme von bis zu 300 kW (Netto-CV Basis) für den nicht-häuslichen Gebrauch.
Dieses Dokument gilt außerdem für Geräte des Typs B11, B11AS, B11BS, B12, B12AS, B12BS, B13, B13AS, B13BS, B14, B14AS, B14BS, B22, B23, B41, B41AS, B41BS, B42, B42AS, B42BS, B43, B43AS, B43BS, B44, B44AS, B44BS, B52, B53, C11, C12, C13, C21, C31, C32, C33, C41, C62 und C63 mit einer Leistungsaufnahme von bis zu 300 kW (Netto-CV Basis) für den häuslichen und nicht-häuslichen Gebrauch.
Die Zufuhr erwärmter Luft darf über Kanalnetze erfolgen.
Dieses Dokument gilt nicht für:
a) Klimaanlagen mit Doppelfunktion (Heizen und Kühlen);
b) Geräte, bei denen die Luft über eine Zwischenflüssigkeit erhitzt wird;
c) tragbare oder transportable Zwangskonvektionsgeräte;
d) Geräte, die mit manuellen oder automatischen Mitteln zur Einstellung der Ableitung von Verbrennungsprodukten durch Abgasklappen ausgestattet sind;
e) aus mehreren Heizeinheiten bestehende Geräte mit einer einzelnen Strömungssicherung;
f) mit einem oder mehreren Abgasaustritten ausgestattete Geräte;
g) mit Gas-Boostern ausgestattete Geräte;
h) C21- und C41-Geräte für die dritte Gasfamilie.
ANMERKUNG Sofern nicht anders angegeben, sind für C41-Geräte die für C21-Geräte geltenden Anforderungen und Prüfverfahren zu beachten.
Dieses Dokument soll keine Geräte umfassen, bei denen beabsichtigt ist, sie an ein Gasnetz anzuschließen, bei welchem die Beschaffenheit des verteilten Gases über die Lebensdauer des Geräts wahrscheinlich stark schwankt.
Dieses Dokument gilt für alle Geräte, die für eine Typprüfung vorgesehen sind.
Générateurs d'air chaud à convection forcée utilisant les combustibles gazeux pour le chauffage de locaux à usage domestique et non domestique, de débit calorifique inférieur ou égal à 300 kW, sur pouvoir calorifique inférieur (PCI)
La présente Norme européenne définit les exigences et les méthodes d’essai relatives à la sécurité et au rendement des générateurs d’air chaud utilisant les combustibles gazeux, avec ou sans ventilateur pour assister le transport de l’air comburant et/ou des produits de combustion, appelés ci-après « appareils ».
La présente Norme européenne s’applique aux appareils de types A2, A3, B11, B11AS, B11BS, B12, B12AS, B12BS, B13, B13AS, B13BS, B14, B14AS, B14BS, B22, B23, B41, B41AS, B41BS, B42, B42AS, B42BS, B43, B43AS, B43BS, B44, B44AS, B44BS, B52, B53, C11, C12, C13, C21, C31, C32, C33, C41, C62 et C63 dont le débit est inférieur ou égal à 300 kW (sur PCI), destinés à être utilisés dans des locaux à usage d'habitation individuelle et autres. La distribution de l'air chaud peut se faire par des conduits.
La présente Norme européenne ne s’applique pas :
a) aux appareils de climatisation à usage double (chauffage et refroidissement) ;
b) aux appareils de chauffage de l'air par un fluide caloporteur intermédiaire ;
c) aux appareils à convection forcée portatifs ou transportables ;
d) aux appareils domestiques destinés à être installés à l'extérieur ;
e) aux appareils dans lesquels le réglage de l'évacuation des produits de combustion à l’aide de clapets de fumée se fait par le biais d'un dispositif manuel ou automatique ;
f) aux appareils comportant plusieurs générateurs de chaleur associés à un seul coupe tirage antirefouleur ;
g) aux appareils comportant plusieurs buses d'évacuation des produits de combustion ;
h) aux appareils comportant des surpresseurs pour le gaz ;
i) aux appareils domestiques de types C22, C23, C42, C43, C52 et C53 ;
j) aux appareils de types C21 et C41 utilisant les gaz de la troisième famille.
NOTE Pour les appareils de type C41, voir l'ensemble des exigences et des méthodes d'essai applicables aux appareils de type C21, sauf indication contraire.
La présente Norme européenne s’applique aux appareils destinés à être soumis à des essais de type. Elle comprend également des exigences relatives à l'évaluation de la conformité, y compris le contrôle de fabrication en usine, ces dernières exigences s’appliquant toutefois exclusivement aux POCED et aux terminaux associés.
Plinski grelniki zraka s prisilno konvekcijo za gretje stanovanjskih in nestanovanjskih prostorov z nazivno močjo do vključno 300 kW
Ta evropski standard določa zahteve in preskusne metode za varnost ter učinkovitost plinskih grelnikov zraka z ventilatorjem ali brez njega za pomoč pri prenosu zgorevalnega zraka in/ali dimnih plinov (v nadaljnjem besedilu »aparati«). Ta evropski standard se uporablja za aparate tipov A2, A3, B11, B11AS, B11BS, B12, B12AS, B12BS, B13, B13AS, B13BS, B14, B14AS, B14BS, B22, B23, B41, B41AS, B41BS, B42, B42AS, B42BS, B43, B43AS, B43BS, B44, B44AS, B44BS, B52, B53, C11, C12, C13, C21, C31, C32, C33, C41, C62 in C63 z nazivno močjo do vključno 300 kW (osnova z neto kalorično vrednostjo), namenjene za uporabo v enostanovanjskih enotah in drugih (večstanovanjskih) enotah. Ogrevani zrak se lahko dovaja prek cevi. Ta evropski standard se ne uporablja za:
a) dvonamenske klimatske naprave (ogrevanje in hlajenje);
b) naprave, pri katerih zrak segreva vmesna tekočina;
c) prenosne ali premične naprave s prisilno konvekcijo;
d) gospodinjske aparate za zunanjo namestitev;
e) naprave, opremljene z ročnimi ali avtomatskimi sredstvi za prilagajanje odvajanja produktov zgorevanja z dimniško loputo;
f) naprave, ki imajo več grelnih enot z enim preusmerjevalnikom vleka;
g) naprave, opremljene z več kot eno dimniško izstopno odprtino;
h) naprave, opremljene s plinskimi ojačevalniki;
i) gospodinjske aparate tipa C22, C23, C42, C43, C52 in C53;
j) aparate C21 in C41 za pline 3. družine;
OPOMBA: Za aparate C41 glej vse zahteve in preskusne metode, ki veljajo za naprave C21, razen če je navedeno drugače. Ta evropski standard se uporablja za aparate, predvidene za tipski preskus. Vključuje tudi zahteve v zvezi z ocenjevanjem skladnosti, vključno z nadzorom tovarniške proizvodnje, vendar te zahteve veljajo samo za sisteme POCED in z njimi povezane terminale.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2020
Nadomešča:
SIST EN 1020:2010
SIST EN 1196:2012
SIST EN 1319:2010
SIST EN 525:2009
SIST EN 621:2010
SIST EN 778:2010
Plinski grelniki zraka s prisilno konvekcijo za gretje stanovanjskih in
nestanovanjskih prostorov z nazivno močjo do vključno 300 kW
Domestic and non-domestic gas-fired forced convection air heaters for space heating not
exceeding a net heat input of 300 kW
Häusliche und nicht-häusliche gasbefeuerte Warmlufterzeuger mit erzwungener
Konvektion zur Raumbeheizung deren Nennwärmebelastung 300 kW nicht übersteigt
Générateurs d'air chaud à convection forcée utilisant les combustibles gazeux pour le
chauffage de locaux à usage domestique et non domestique, de débit calorifique
inférieur ou égal à 300 kW, sur pouvoir calorifique inférieur (PCI)
Ta slovenski standard je istoveten z: EN 17082:2019
ICS:
97.100.20 Plinski grelniki Gas heaters
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 17082
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 97.100.20 Supersedes EN 1020:2009, EN 1196:2011, EN
1319:2009, EN 525:2009, EN 621:2009, EN 778:2009
English Version
Domestic and non-domestic gas-fired forced convection air
heaters for space heating not exceeding a net heat input of
300 kW
Générateurs d'air chaud à convection forcée utilisant Häusliche und nicht-häusliche gasbefeuerte
les combustibles gazeux pour le chauffage de locaux à Warmlufterzeuger mit erzwungener Konvektion zur
usage domestique et non domestique, de débit Raumbeheizung deren Nennwärmebelastung 300 kW
calorifique inférieur ou égal à 300 kW, sur pouvoir nicht übersteigt
calorifique inférieur (PCI)
This European Standard was approved by CEN on 5 June 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
C O M I T É E U R O P É E N D E N O R M A L I S A T I O N
E U R O P Ä I S C H E S K O M I T E E F Ü R N O R M U N G
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17082:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 6
4 Classification . 23
5 Construction and design requirement . 24
6 Operational requirements . 59
7 Efficiency . 142
8 Risk assessment . 148
9 Marking and instructions . 148
Annex A (informative) National situations . 160
Annex B (normative) Equivalence rules . 163
Annex C (informative) Identification of gas types in use in various countries . 165
Annex D (normative) Mode of air supply and evacuation of combustion products . 167
Annex E (informative) NOx Measurements . 171
Annex F (informative) Derivation of Thermal Efficiency Equations . 172
Annex G (informative) Facilities for commissioning and testing (see 5.12) . 174
Annex H (normative) Requirements in EN 17082 which relate to the design and construction of
forced draught burners covered in EN 676:2003+A2:2008 . 176
Annex I (normative) Tolerances of measurements . 178
Annex J (informative) Guidance for limitations of application of direct-fired air heaters in
buildings . 181
Annex K (normative) Flue test probes . 186
Annex ZA (informative) Relationship between this European Standard and the ecodesign
requirements of Commission Regulation (EU) No 2016/2281 aimed to be covered . 192
Bibliography . 193
European foreword
This document (EN 17082:2019) has been prepared by Technical Committee CEN/TC 180
“Decentralized gas heating”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by April 2020, and conflicting national
standards shall be withdrawn at the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights. CEN shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN 525:2009, EN 621:2009, EN 778:2009, EN 1196:2011, EN
1020:2009 and EN 1319:2009.
This document covers the safety and energy efficiency requirements of domestic and non-
domestic warm air heaters previously covered by EN 525:2009, EN 621:2009, EN 778:2009, EN
1196:2011, EN 1020:2009 and EN 1319:2009. Additional technical requirements have been
made compared to the superseded documents to take account the following:
— Specific requirements on risk analysis due to differences in the Essential Requirements for
the Gas Appliance Regulation compared to those of the Gas Appliance Directive;
— Additional requirements on appliance efficiency, including the need to calculate the
seasonal efficiency related to the requirements of the Eco-Design Regulation.
Changes have also been made to the document structure to improve its ease of use, for example
requirements and associated test methods have been moved into the same clause.
This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of
EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain,
Sweden, Switzerland, Turkey and the United Kingdom.
1 Scope
This document specifies the requirements and test methods for the safety and efficiency of gas
fired air heaters with or without a fan to assist the transportation of combustion air and/or flue
gases, hereafter referred to as "appliances".
This document also applies to warm air heaters having forced draught burners.
This document applies to Type A , A appliances, with an input not exceeding 300 kW (net CV
2 3
basis), intended for non-domestic use.
This document also applies to Type B , B , B , B , B , B , B , B , B , B , B ,
11 11AS 11BS 12 12AS 12BS 13 13AS 13BS 14 14AS
B , B , B , B , B , B , B , B , B , B , B , B , B , B , B , B , B , C , C , C ,
14BS 22 23 41 41AS 41BS 42 42AS 42BS 43 43AS 43BS 44 44AS 44BS 52 53 11 12 13
C , C , C , C , C , C and C appliances with an input not exceeding 300 kW (net CV basis),
21 31 32 33 41 62 63
intended for domestic and non-domestic use.
Provision of the heated air may be by means of ducting.
This document does not apply to:
a) dual purpose air conditioning appliances (heating and cooling);
b) appliances where the air is heated by an intermediate fluid;
c) portable or transportable forced convection appliances;
d) appliances fitted with manual or automatic means of adjusting the combustion products
evacuation by means of flue dampers;
e) appliances having multiple heating units with a single draught diverter;
f) appliances fitted with more than one flue outlet;
g) appliances fitted with gas boosters;
h) C and C appliances for 3rd family gases.
21 41
NOTE For C appliances, see all requirements and test methods that are valid for C appliances,
41 21
unless otherwise stated.
This document is not intended to cover appliances projected for connection to gas grids where
the quality of the distributed gas is likely to vary to a large extent over the lifetime of the
appliance.
This document is applicable to appliances which are intended to be type tested.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition cited
applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
EN 88-1:2011+A1 2016, Pressure regulators and associated safety devices for gas appliances —
Part 1: Pressure regulators for inlet pressures up to and including 50 kPa
EN 125:2010+A1 2015, Flame supervision devices for gas burning appliances — Thermoelectric
flame supervision devices
EN 126:2012, Multifunctional controls for gas burning appliances
EN 161:2011+A3:2013, Automatic shut-off valves for gas burners and gas appliances
EN 257:2010, Mechanical thermostats for gas-burning appliances
EN 298:2012, Automatic burner control systems for burners and appliances burning gaseous or
liquid fuels
EN 437:2003+A1:2009, Test gases — Test pressures — Appliance categories
EN 676:2003+A2:2008, Automatic forced draught burners for gaseous fuels
EN 682:2002, Elastomeric seals — Materials requirements for seals used in pipes and fittings
carrying gas and hydrocarbon fluids
EN 1859:2009+A1:2013, Chimneys— Metal chimneys — Test methods
EN 10226-2:2005, Pipe threads where pressure tight joints are made on the threads — Part 2:
Taper external threads and taper internal threads — Dimensions, tolerances and designation
EN 12067-2:2004, Gas/air ratio controls for gas burners and gas burning appliances — Part 2:
Electronic types
EN 50090 (all parts), Home and Building Electronic Systems (HBES)
EN 60335-1:2012, Household and similar electrical appliances — Safety — Part 1: General
requirements (IEC 60335-1:2010, modified)
EN 60335-2-102:2016, Household and similar electrical appliances — Safety - Part 2-102:
Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections
(IEC 60335-2-102:2004, modified)
EN 60529:1991, Degrees of protection provided by enclosures (IP code) (IEC 60529:1989)
EN 60584-1:2013, Thermocouples — Part 1: EMF specifications and tolerances (IEC 60584-
1:2013)
EN 60730-1:2016, Automatic electrical controls — Part 1: General requirements (IEC 60730-
1:2013, modified)
EN 60730-2-9:2010, Automatic electrical controls for household and similar use — Part 2-9:
Particular requirements for temperature sensing controls (IEC 60730-2-9:2008, modified)
EN 61058-1:2002, Switches for appliances — Part 1: General requirements (IEC 61058-1:2000,
modified)
EN 61558-2-6:2009, Safety of transformers, reactors, power supply units and similar products for
supply voltages up to 1 100 V — Part 2-6: Particular requirements and tests for safety isolating
transformers and power supply units incorporating safety isolating transformers (IEC 61558-2-
6:2009)
EN 61558-2-16:2009, Safety of transformers, reactors, power supply units and similar products
for
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.