EN 10219-2:2019
(Main)Cold formed welded steel structural hollow sections - Part 2: Tolerances, dimensions and sectional properties
Cold formed welded steel structural hollow sections - Part 2: Tolerances, dimensions and sectional properties
This document specifies tolerances for cold formed welded circular, square, rectangular and elliptical structural hollow sections, manufactured in wall thicknesses up to 40 mm, in the following size ranges:
- circular: Outside diameters up to 2 500 mm;
- square: Outside dimensions up to 500 mm × 500 mm;
- rectangular: Outside dimensions up to 500 mm × 300 mm;
- elliptical: Outside dimensions up to 480 mm × 240 mm.
The formulae for calculating sectional properties of sections manufactured to the dimensional tolerances of this standard, to be used for the purposes of structural design, are given in Annex A.
Dimensions and sectional properties for a limited range of more common sizes are given in Annex B.
NOTE The designation of the sections' major axis (yy) and minor axis (zz) aligns with the axis designation used for structural design in the structural Eurocodes.
Kaltgeformte geschweißte Hohlprofile für den Stahlbau - Teil 2: Grenzabmaße, Maße und statische Werte
Dieses Dokument legt die Grenzabmaße und Formtoleranzen für kaltgeformte geschweißte Hohlprofile für den Stahlbau mit kreisförmigem, quadratischem, rechteckigem oder elliptischem Querschnitt fest; hergestellt in Wanddicken bis 40 mm und den folgenden Abmessungen:
- kreisförmig: Außendurchmesser bis zu 2 500 mm;
- quadratisch: Außendurchmesser bis zu 500 mm x 500 mm;
- rechteckig: Außendurchmesser bis zu 500 mm x 300 mm;
- elliptisch: Außendurchmesser bis zu 480 mm x 240 mm.
Die Formeln zur Berechnung der statischen Werte zur Festigkeitsauslegung der Hohlprofile, die gemäß der Grenzabmaße dieser Norm hergestellt werden, sind in Anhang A angegeben.
Die Maße und statischen Werte sind für eine begrenzte Anzahl üblicher Abmessungen in Anhang B angegeben.
ANMERKUNG Die Bezeichnung der Hauptachsen (yy) und die der Nebenachsen (zz) der Hohlprofile erfolgt in Anlehnung an die Achsenbezeichnung, die für die Festigkeitsauslegung in den Eurocodes verwendet wird.
Profils creux de construction soudés, formés à froid en aciers - Partie 2 : Tolérances, dimensions et caractéristiques de section
Le présent document spécifie les tolérances pour les profils creux de construction soudés, formés à froid circulaires, carrés, rectangulaires ou elliptiques, fabriqués en épaisseur jusqu’à 40 mm, pour les gammes de dimensions suivantes :
- Circulaire : Diamètres extérieurs jusqu’à 2 500 mm ;
- Carré : Dimensions extérieures jusqu’à 500 mm x 500 mm ;
- Rectangulaire : Dimensions extérieures jusqu’à 500 mm x 300 mm ;
- Elliptique : Dimensions extérieures jusqu’à 480 mm x 240 mm.
Les formules pour le calcul des caractéristiques de section pour les profils fabriqués aux tolérances dimensionnelles de la présente norme, à utiliser pour les besoins de la conception de structures, sont données en Annexe A.
Les dimensions et les caractéristiques de section pour une gamme limitée des dimensions les plus courantes sont données à l’Annexe B.
NOTE La désignation de l’axe principal (yy) et de l’axe secondaire (zz) du profil est alignée sur la désignation des axes utilisée en conception dans les Eurocodes de construction.
Hladno oblikovani varjeni votli konstrukcijski profili iz jekla - 2. del: Mere, mejni odstopki in značilnosti profilov
Ta del standarda prEN 10219 določa mejne odstopke za hladno oblikovane krožne, kvadratne, pravokotne in ovalne votle konstrukcijske profile, izdelane z debelino sten do 40 mm, v naslednjih razponih velikosti:
Okrogli: zunanji premer do 2.500 mm
Kvadratni: zunanje dimenzije do 500 mm × 500 mm
Pravokotni: zunanje dimenzije do 500 mm × 300 mm
Ovalni: zunanje dimenzije do 480 mm × 240 mm
Formule za izračun značilnosti profilov, izdelanih v okviru dimenzijskih mejnih odstopkov tega standarda, ki se uporabljajo za projektiranje konstrukcij, so navedene v dodatku B.
Dimenzije in značilnosti profilov za omejen nabor pogostejših velikosti so navedene v dodatku B.
Splošni pogoji so določeni v standardu prEN 10219-1 (značilnosti izdelkov, preskusni postopki in merila učinkovitosti, ki veljajo v skladu z uredbami o gradbenih proizvodih) in tehničnih dobavnih pogojih v standardu prEN 10219-2.
OPOMBA: Označevanje daljše osi profila (yy) in njegove krajše osi (zz) se ujema z oznako osi, ki se uporablja za konstrukcijsko projektiranje v konstrukcijskih evrokodih.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2019
Nadomešča:
SIST EN 10219-2:2006
Hladno oblikovani varjeni votli konstrukcijski profili iz jekla - 2. del: Mere, mejni
odstopki in značilnosti profilov
Cold formed welded steel structural hollow sections - Part 2: Tolerances, dimensions and
sectional properties
Kaltgefertigte geschweißte Hohlprofile für den Stahlbau aus unlegierten Baustählen und
aus Feinkornbaustählen - Teil 2: Grenzabmaße, Maße und statische Werte
Profils creux de construction soudés, formés à froid en aciers non alliés et à grains fins -
Partie 2 : Tolérances, dimensions et caractéristiques de profil
Ta slovenski standard je istoveten z: EN 10219-2:2019
ICS:
77.140.45 Nelegirana jekla Non-alloyed steels
77.140.70 Jekleni profili Steel profiles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 10219-2
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2019
EUROPÄISCHE NORM
ICS 77.140.75
English Version
Cold formed welded steel structural hollow sections - Part
2: Tolerances, dimensions and sectional properties
Profils creux de construction soudés, formés à froid en Kaltgeformte geschweißte Hohlprofile für den Stahlbau
aciers - Partie 2 : Tolérances, dimensions et - Teil 2: Grenzabmaße, Maße und statische Werte
caractéristiques du profil
This European Standard was approved by CEN on 20 March 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10219-2:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Symbols . 4
5 Information to be obtained by the manufacturer . 5
6 Tolerances . 6
7 Measurement of size and shape . 8
8 Dimensions and sectional properties . 13
Annex A (normative) Formulae for the calculation of sectional properties . 14
A.1 General . 14
A.2 Circular hollow sections . 14
A.3 Rectangular or square, hollow sections . 15
A.4 Elliptical hollow sections . 17
Annex B (normative) Sectional properties for a limited range of standard sizes . 19
Bibliography . 44
European foreword
This document (EN 10219-2:2019) has been prepared by Technical Committee CEN/TC 459 “ECISS -
European Committee for Iron and Steel Standardization” , the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2019, and conflicting national standards
shall be withdrawn at the latest by November 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10219-2:2006.
The main changes with respect to the previous edtion are listed below:
a) elliptical hollow sections were added;
b) Annex A concerning the additional tolerances for piling tubes was removed;
c) subclause 5.2 was added with one option;
d) in Table 3 the length tolerances for exact length were changed;
e) in 7.1 one paragraph was added;
f) standard was editorially revised.
This standard consists of the following parts:
— EN 10368, Steel structural hollow sections – General (Characteristics, evaluation of conformity and
marking) (in preparation)
— EN 10219-1, Cold formed welded steel structural hollow sections - Part 1: Technical delivery
conditions
— EN 10219-2, Cold formed welded steel structural hollow sections - Part 2: Tolerances, dimensions and
sectional properties
— EN 10219-3, Cold formed welded steel structural hollow sections - Part 3: Technical delivery
conditions for mechanical engineering purposes (in preparation)
It forms part of a series of standards on hollow sections together with EN 10210-1 to EN 10210-3.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Through its subcommittee SC 3 “Structural steels other than reinforcements” (secretariat: DIN)
1 Scope
This document specifies tolerances for cold formed welded circular, square, rectangular and elliptical
structural hollow sections, manufactured in wall thicknesses up to 40 mm, in the following size ranges:
— circular: Outside diameters up to 2 500 mm;
— square: Outside dimensions up to 500 mm × 500 mm;
— rectangular: Outside dimensions up to 500 mm × 300 mm;
— elliptical: Outside dimensions up to 480 mm × 240 mm.
The formulae for calculating sectional properties of sections manufactured to the dimensional
tolerances of this standard, to be used for the purposes of structural design, are given in Annex A.
Dimensions and sectional properties for a limited range of more common sizes are given in Annex B.
NOTE The designation of the sections' major axis (yy) and minor axis (zz) aligns with the axis designation
used for structural design in the structural Eurocodes.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10219-1, Cold formed welded structural hollow sections of non-alloy and fine grain steels — Part 1:
Technical delivery conditions
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 10219-1 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
4 Symbols
For the purposes of this document, the symbols defined in Table 1 apply.
Table 1 — Symbols and definitions
Symbol Unit Definition
A cm Cross-sectional area
A mm Area of the surface delimited by the perimeter at mid-thickness
m
A m /m Superficial area per metre length
s
B mm Specified side dimension of a square hollow section. Specified
dimension of the shorter side of a rectangular hollow section. Specified
outside dimension of an elliptical section on its minor axis
C /C mm Length of corner region of a square or rectangular hollow section
1 2
Symbol Unit Definition
C cm Torsional modulus constant
t
D mm Specified outside diameter of a circular hollow section
D /D mm Maximum and minimum outside diameter of a circular hollow section
max min
measured in the same plane
e mm Deviation from straightness
H mm Specified dimension of the longer side of a rectangular hollow section.
Specified outside dimension of an elliptical section on its major axis
I cm Second moment of area
I cm Torsional inertia constant (polar moment of inertia in the case of
t
circular hollow sections only)
i cm Radius of gyration
L mm Length
M kg/m Mass per unit length
O % Out-of-roundness
P mm External perimeter of an elliptical hollow section
R mm External corner radius of a square or rectangular hollow section
T mm Specified thickness
U mm Perimeter of an elliptical hollow section at mid-thickness
V mm Total measured twist
V mm Twist measured at one end of a section
W cm Elastic section modulus
el
W cm Plastic section modulus
pl
x mm Concavity of a side of a square or rectangular hollow section
x mm Convexity of a side of a square or rectangular hollow section
yy — Axis of cross-section, major axis of a rectangular hollow section
zz — Axis of cross-section, minor axis of a rectangular hollow section
θ ° Angle between adjacent sides of a square or rectangular hollow section
5 Information to be obtained by the manufacturer
5.1 Mandatory information
The following mandatory information from this part of EN 10219 shall be obtained by the manufacturer
at the time of enquiry and order:
a) the dimensions (see Clause 8);
b) the type of length, length range or length (see Table 4);
NOTE This information is included in the list of information to be obtained by the manufacturer contained in
EN 10219-1.
5.2 Options
An option is specified in this part of EN 10219. In the event that the purchaser does not indicate a wish
to implement this at the time of enquiry and order, the manufacturer shall supply in accordance with
the basic specification.
Option 2.1 Out-of-roundness tolerances for diameter to thickness ratio exceeding 100 (see
Table 2, footnote a).
6 Tolerances
6.1 Tolerances shall not exceed the values given in Table 2 for shape and mass, Table 3 for external
corner profiles, Table 4 for manufacturer's delivered length and Table 5 for the height of the internal
and external weld bead of submerged arc welded hollow sections.
6.2 The internal corners of square and rectangular hollow sections shall be rounded.
NOTE The internal corner profile is not specified.
Table 2 — Tolerances on shape, straightness and mass
Characteristic Circular hollow Square and rectangular Elliptical hollow
sections hollow sections section
Side Tolerance
length
mm
Outside dimensions (D, ±1 % with a minimum H, ±1 % with a ±1 % with a
B and H) of ± 0,5 mm and a B < 100 minimum minimum
maximum of ± 10 mm of ± 0,5 mm of ± 0,5 mm
100 ≤ H, ±0,8 %
B ≤ 200
H, ±0,6 %
B > 200
Thickness (T) For D ≤ 406,4 mm: T ≤ 5 mm ± 10 % T ≤ 5 mm ± 10 %
T ≤ 5 mm ± 10 % T > 5 mm ± 0,5 mm T > 5 mm ± 0,5 mm
T > 5 mm ± 0,5 mm
For D > 406,4 mm:
±10 % with a
maximum of ± 2 mm
Out-of-roundness (O) 2 % for hollow — —
sections having a
diameter to thickness
ratio not exceeding
a
Concavity/convexity — Max. 0,8 % with a —
b minimum of 0,5 mm
(x , x )
1 2
Characteristic Circular hollow Square and rectangular Elliptical hollow
sections hollow sections section
Side Tolerance
length
mm
Squareness of side (θ) — 90° ± 1° —
External corner profile — See Table 3 —
(C C or R)
1, 2
Twist (V) — 2 mm plus 0,5 mm/m —
length
Straightness (e) 0,20 % of total length 0,15 % of total length and 0,20 % of total length
and 3 mm over any 3 mm over any 1 m length and 3 mm over
1 m length any 1 m length
Mass per unit length ±6 % on individual delivered lengths
(M)
a
When the diameter to thickness ratio exceeds 100, application of tolerance on out-of-roundness is not
required, unless specifically agreed (see 5.2).
b
The tolerance on convexit
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.