EN 15743:2010/FprA1
(Amendment)Supersulfated cement - Composition, specifications and conformity criteria
Supersulfated cement - Composition, specifications and conformity criteria
See edition of 2011. The amendment concerns the adequation to the CPR.
Sulfathüttenzement - Zusammensetzung, Anforderungen und Konformitätskriterien
Ciment sursulfaté - Composition, spécifications et critères de conformité
Supersulfatni cement - Sestava, zahteve in merila skladnosti
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2014
6XSHUVXOIDWQLFHPHQW6HVWDYD]DKWHYHLQPHULODVNODGQRVWL]DRELþDMQHFHPHQWH
Supersulfated cement - Composition, specifications and conformity criteria
Sulfathüttenzement - Zusammensetzung, Anforderungen und Konformitätskriterien
Ciment sursulfaté - Composition, spécifications et critères de conformité
Ta slovenski standard je istoveten z: EN 15743:2010/FprA1
ICS:
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
FINAL DRAFT
EN 15743:2010
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
July 2014
ICS 91.100.10
English Version
Supersulfated cement - Composition, specifications and
conformity criteria
Ciment sursulfaté - Composition, spécifications et critères Sulfathüttenzement - Zusammensetzung, Anforderungen
de conformité und Konformitätskriterien
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 51.
This draft amendment A1, if approved, will modify the European Standard EN 15743:2010. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15743:2010/FprA1:2014 E
worldwide for CEN national Members.
Contents
Page
Foreword .3
1 Modification to Clause 2 .4
2 Modification to Clause 7 .4
3 Modification to 9.1 .4
4 Modification to Annex ZA .4
Foreword
This document (EN 15743:2010/FprA1:2014) has been prepared by Technical Committee CEN/TC 51
“Cement and building limes”, the secretariat of which is held by NBN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Regulation(s).
For relationship with EU Regulation(s), see informative Annex ZA, which is an integral part of this document.
This European Standard sets out requirements for the composition and specifications of supersulfated
cement. The scheme for the evaluation of conformity of supersulfated cement is that specified in EN 197-2.
Compared to the version EN 15743:2010 the following major changes have been included in this document:
Clause “Dangerous substances”;
Use of the terminology given by the Construction Products Regulation (Regulation (EU) No 305/2011) in
9.1;
Adaption of Annex ZA to the new CEN template.
The requirements in this European Standard are based on the results of tests on cement in accordance with
parts 1, 2, 3, 7, 8 and 9 of EN 196, Methods of testing cement.
Note: Due to fact that the Framework Partnership Agreement between the Commission and CEN & CENELEC
is not signed yet, there are currently no New Approach Consultants in place for 2014. Therefore the provisions
of CEN-CENELEC Guide 15 cannot be met.
This shall not prevent the processing of draft standards nor the offering of harmonized standards to the
Commission. In particular, draft standards can be sent to vote without Consultant assessment.
This note will be removed from the Foreword of the finalized publication.
1 Modification to Clause 2
Replace "EN 197-2:2000" with EN 197-2:2014".
2 Modification to Clause 7
Add the following new sub-clause 7.5:
"7.5 Dangerous substances
National regulations on dangerous substances may require verification and declaration on release, and
sometimes content, when construction products covered by this standard are placed on those markets.
In the absence of European harmonized test methods, verification and declaration on release/content should
be done taking into account national provisions in the place of use.
NOTE An informative database covering European and national provisions on dangerous substances is available at
the Construction web site on EUROPA accessed through: http://ec.europa.eu/enterprise/construction/cpd-ds/"
3 Modification to 9.1
nd
Replace the 2 paragraph and the note with the following:
"Alternative test methods could be used provided that they have been validated in accordance with the
appropriate provisions in the cited standards of the reference test methods. In the event of a dispute, only the
reference methods are used.
NOTE 1 This standard does not deal with acceptance inspection at delivery.
NOTE 2 For certification of constancy of performance by a notified body, conformity of cement with this standard is
evaluated in accordance with EN 197-2.
The compliance of the supersulfated cements with the requirements of this European Standard and with the
stated values (including classes) shall be demonstrated by:
determination of the product type,
factory production control by the manufacturer, including product assessment."
4 Modification to Annex ZA
Replace the entire Annex ZA with the following text:
"
Annex ZA
(informative)
Clauses of this European Standard addressing the provisions of the
EU Construction Products Regulation
ZA.1 Scope and relevant characteristics
This European Standard has been prepared under Mandate M/114 “Cement, building limes and other
hydraulic binders” given to CEN by the European Commission and the European Free Trade Association.
If this European Standard is cited in the Official Journal of the European Union (OJEU), the clauses of this
standard, shown in this annex, are considered to meet the provisions of the relevant mandate, under the
Regulation (EU) No. 305/2011.
This annex deals with the CE marking of the common cements intended for the uses indicated in Table ZA.1
and shows the relevant clauses applicable.
This annex has the same scope as in Clause 1 of this standard related to the aspects covered by the mandate
and is defined by Table ZA.1.
Table ZA.1 — Relevant clauses
Product: Supersulfated cement
Intended use: Preparation of concrete, mortar, grout etc. (see notes in this table)
Clauses in this and
other European
Regulatory
Essential Characteristics Standard(s) related Notes
classes
to essential
characteristics
Constitutions of the supersulfated cement,
defined on the basis of constituent materials and
Supersulfated cements composition; selection of supersulfated cement
(Subfamilies) constituents None by the Member States in technical regulations for
particular intended uses shall be possible, based
and composition
on the different cement products and on strength
classes
7.1.1
Compressive strength Compressive strength requirements expressed
None
in terms of strength classes and limits
(early and standard)
7.2.1
Requirements expressed in terms of lower limits
Setting time None
7.3
Insoluble residue None Requirements expressed in terms of upper limits
7.3
Loss on ignition None Requirements expressed in terms of upper limits
7.2.2
Requirements expressed in terms of upper limit
Soundness None
7.3 Requirements expressed in terms of lower and
SO content
None
9 upper limits
7.3
Requirements expressed in terms of upper limits
Chloride content None
7.2.3
Requirements expressed in terms of upper limit
Heat of hydration None
4 Durability relates to the concrete, mortar, grout
Durability, sulfate
5 None and other mixes made from cement according to
resistance
7.4 the application rules valid in the place of use
Content and/or release of
7.5 None See 7.5
dangerous substances
The declaration of the product performance related to certain essential characteristics is not required in those
Member States (MS) where there are no regulatory requirements on these essential characteristics for the
intended use of the product. In this case, manufacturers placing their products on the market of these MS are
not obliged to determine nor declare the performance of their products with regard to these essential
characteristics and the option “No performance determined” (NPD) in the information accompanying the CE
marking and in the declaration of performance (see ZA.3) may be used for those essential characteristics.
ZA.2 Procedure for AVCP of supersulfated cements
ZA.2.1 System of AVCP
The AVCP system of common cements indicated in Table ZA.1, established by EC Decision 97/555/EC
(OJ L229) amended by EC Decision 2010/683/EU (OJ L293), is shown in Table ZA.2 for the indicated
intended use(s) and relevant level(s) or class(es) of performance.
Table ZA.2 — System of AVCP
Product(s) Intended use(s) Level(s) or class(es) AVCP system
Supersulfated cement Preparation of concrete, mortar, grout etc. None 1+
System 1+: See Regulation (EU) No. 305/2011 (CPR) Annex V, 1.1 with audit testing of samples taken before
placing the product on the market.
The AVCP of the supersulfated cements in Table ZA.1 shall be according to the AVCP procedures indicated
in Table ZA.3 resulting from application of the clauses of this or other European Standards indicated therein.
The content of tasks of the notified body shall be limited to those essential characteristics as provided for, if
any, in Annex III of the relevant mandate and to those that the manufacturer intends to declare.
Table ZA.3 — Assignment of AVCP tasks for supersulfated cements under system 1+
Evaluation of
conformity clauses to
Tasks Content of the task apply in addition to
Clause 9 of this
standard
Parameters related to essential
EN 197-2:2014,
Factory production control (FPC) characteristics of Table ZA.1 relevant for
Clause 4
the intended use(s) which are declared
Tasks for the
manufacturer Further testing of samples taken Essential characteristics of Table ZA.1
EN 197-2:2014,
at factory according to the relevant for the intended use(s) which
4.3
prescribed test plan are declared
Determination of the product-type
on the basis of type testing
(including sampling), type Essential characteristics of Table ZA.1 EN 197-2:2014,
calculation, tabulated values or relevant for the intended use(s) Clause 5
descriptive documentation of the
product
Parameters related to essential
Tasks for the Initial inspection of the characteristics of Table ZA.1, relevant EN 197-2:2014,
notified product manufacturing plant and of FPC for the intended use(s) which are 5.5
declared. Documentation of the FPC.
certification body
Parameters related to essential
Continuous surveillance,
characteristics of Table ZA.1, relevant EN 197-2:2014,
assessment and evaluation of
for the intended use(s) which are 5.2
FPC
declared. Documentation of the FPC.
Audit testing of samples taken Essential characteristics of Table ZA.1
EN 197-2:2014,
before placing the product on the relevant for the intended use(s) which
5.4
market are declared
ZA.2.2 Declaration of performance (DoP)
ZA.2.2.1 General
The manufacturer draws up the DoP and affixes the CE marking on the basis of the different AVCP systems
set out in Annex V of the Regulation (EU) No 305/2011:
the factory production control and the further testing of samples taken at the factory according to the
prescribed test plan, carried out by the manufacturer; and
the certificate of constancy of performance issued by the notified product certification body on the basis of
determination of the product type on the basis of type testing (including sampling), type calculation,
tabulated values or descriptive documentation of the product; initial inspection of the manufacturing plant
and of factory production control; continuous surveillance, assessment and evaluation of factory
production control and audit-testing of samples taken before placing the product on the market.
ZA.2.2.2 Content
The model of the DoP is provided in Annex III of the Regulation (EU) No 305/2011.
According to this Regulation, the DoP shall contain, in particular
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.