EN ISO 21656:2021
(Main)Solid recovered fuels - Determination of ash content (ISO 21656:2021)
Solid recovered fuels - Determination of ash content (ISO 21656:2021)
This document specifies methods for the determination of ash content of all solid recovered fuels.
Feste Sekundärbrennstoffe - Bestimmung des Aschegehaltes (ISO 21656:2021)
Dieses Dokument legt Verfahren zur Bestimmung des Aschegehaltes sämtlicher festen Sekundärbrennstoffe fest.
Combustibles solides de récupération - Détermination de la teneur en cendres (ISO 21656:2021)
Le présent document spécifie des méthodes de détermination de la teneur en cendres pour tous les combustibles solides de récupération.
Trdna alternativna goriva - Določevanje vsebnosti pepela (ISO 21656:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2021
Nadomešča:
SIST EN 15403:2011
Trdna alternativna goriva - Določevanje vsebnosti pepela (ISO 21656:2021)
Solid recovered fuels - Determination of ash content (ISO 21656:2021)
Feste Sekundärbrennstoffe - Bestimmung des Aschegehaltes (ISO 21656:2021)
Combustibles solides de récupération - Détermination de la teneur en cendres (ISO
21656:2021)
Ta slovenski standard je istoveten z: EN ISO 21656:2021
ICS:
75.160.10 Trda goriva Solid fuels
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 21656
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2021
EUROPÄISCHE NORM
ICS 75.160.10 Supersedes EN 15403:2011
English Version
Solid recovered fuels - Determination of ash content (ISO
21656:2021)
Combustibles solides de récupération - Détermination Feste Sekundärbrennstoffe - Bestimmung des
de la teneur en cendres (ISO 21656:2021) Aschegehaltes (ISO 21656:2021)
This European Standard was approved by CEN on 6 March 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21656:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 21656:2021) has been prepared by Technical Committee ISO/TC 300 "Solid
recovered materials, including solid recovered fuels" in collaboration with Technical Committee
CEN/TC 343 “Solid Recovered Fuels” the secretariat of which is held by SFS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2021, and conflicting national standards
shall be withdrawn at the latest by September 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15403:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 21656:2021 has been approved by CEN as EN ISO 21656:2021 without any modification.
INTERNATIONAL ISO
STANDARD 21656
First edition
2021-02
Solid recovered fuels — Determination
of ash content
Combustibles solides de récupération — Détermination de la teneur
en cendres
Reference number
ISO 21656:2021(E)
©
ISO 2021
ISO 21656:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
ISO 21656:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Sampling and sample preparation . 3
6.1 General . 3
6.2 Pre-drying . 3
6.3 Removed ash contributors (rac) . 3
7 Procedure. 3
7.1 General . 3
7.2 Method A – ash content at 550 °C . 3
7.3 Method B – ash content at 815 °C . 4
8 Calculation . 5
8.1 General analysis sample . 5
8.2 Calculation of total ash content including removed ash contributors, on an as
received and dry basis . 5
9 Precision . 6
9.1 Repeatability limit . 6
9.2 Reproducibility limit . 6
10 Test report . 6
Annex A (informative) Interlaboratory test results . 8
Annex B (informative) Environmental aspects .11
Bibliography .13
ISO 21656:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 300, Solid recovered fuels, in collaboration
with the European Committee for Standardization (CEN) Technical Committee CEN/TC 343, Solid
recovered fuels, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
ISO 21656:2021(E)
Introduction
This document covers the determination of ash content of solid recovered fuels. It is primarily geared
toward laboratories, producers, suppliers and purchasers of solid recovered fuels but is also useful for
the authorities and inspection organizations.
[5]
The method A specified in this document is based on EN 15403 .
For information about environmental aspect, see Annex B.
INTERNATIONAL STANDARD ISO 21656:2021(E)
Solid recovered fuels — Determination of ash content
1 Scope
This document specifies methods for the determination of ash content of all solid recovered fuels.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 21637, Solid recovered fuels — Vocabulary
ISO 21645, Solid recovered fuels —
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.