EN ISO 11363-2:2017
(Main)Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 2: Inspection gauges (ISO 11363-2:2017)
Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 2: Inspection gauges (ISO 11363-2:2017)
ISO 11363-2:2017 specifies types, dimensions and principles of use of gauges, to be used in conjunction with the taper threads specified in ISO 11363-1 (i.e. 17E and 25E threads).
It provides examples of calculations for thread gauge dimensions on the large end diameter (Annex A) and draws attention to the limitations of the gauging system specified (Annex B).
Gasflaschen - 17E und 25E kegeliges Gewinde zur Verbindung von Ventilen mit Gasflaschen - Teil 2: Prüflehren (ISO 11363-2:2017)
Dieses Dokument legt Typen, Maße und Anwendungsgrundsätze von Lehren, die in Verbindung mit den kegeligen Gewinden nach ISO 11363-1 (d. h. 17E- und 25E-Gewinde) angewendet werden, fest.
Es enthält Berechnungsbeispiele für die Abmaße von Gewindelehren für den großen Kegeldurchmesser (Anhang A) und weist auf die Grenzen des in der vorliegenden Norm festgelegten Lehren-Systems (Anhang B) hin.
Bouteilles à gaz - Filetages coniques 17E et 25E pour le raccordement des robinets sur les bouteilles à gaz - Partie 2: Calibres de contrôle (ISO 11363-2:2017)
L'ISO 11363-2 :2017 spécifie les types, les dimensions et les principes d'utilisation des calibres, à utiliser conjointement avec les cônes filetés spécifiés dans l'ISO 11363‑1 (c'est-à-dire à filetages 17E et 25E).
Il donne des exemples de calculs des dimensions de calibres filetés fondés sur le diamètre de la grosse extrémité (Annexe A) et il attire l'attention sur les limites du système de vérification par calibres spécifié (Annexe B).
Plinske jeklenke - Konična navoja 17E in 25E za priključitev ventila na plinsko jeklenko - 2. del: Kalibri za kontrolo (ISO 11363-2:2017)
Ta dokument določa vrste, mere in načela uporabe meritev, ki bodo uporabljeni skupaj s koničastimi navoji, določenimi v standardu ISO 11363-1 (tj. navoji 17E in 25E).
Zagotavlja primere izračunov za mere kalibrov navojev pri premeru velikega konca (Dodatek A)
in usmerja pozornost k določenim omejitvam merilnega sistema (Dodatek B).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2018
1DGRPHãþD
SIST EN ISO 11363-2:2010
3OLQVNHMHNOHQNH.RQLþQDQDYRMD(LQ(]DSULNOMXþLWHYYHQWLODQDSOLQVNR
MHNOHQNRGHO .DOLEUL]DNRQWUROR ,62
Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders -
Part 2: Inspection gauges (ISO 11363-2:2017)
Gasflaschen - 17E und 25E kegeliges Gewinde zur Verbindung von Ventilen mit
Gasflaschen - Teil 2: Prüflehren (ISO 11363-2:2017)
Bouteilles à gaz - Filetages coniques 17E et 25E pour le raccordement des robinets sur
les bouteilles à gaz - Partie 2: Calibres de contrôle (ISO 11363-2:2017)
Ta slovenski standard je istoveten z: EN ISO 11363-2:2017
ICS:
21.040.30 Posebni navoji Special screw threads
23.020.35 Plinske jeklenke Gas cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 11363-2
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2017
EUROPÄISCHE NORM
ICS 23.020.35 Supersedes EN ISO 11363-2:2010
English Version
Gas cylinders - 17E and 25E taper threads for connection
of valves to gas cylinders - Part 2: Inspection gauges (ISO
11363-2:2017)
Bouteilles à gaz - Filetages coniques 17E et 25E pour le Gasflaschen - 17E und 25E kegeliges Gewinde zur
raccordement des robinets sur les bouteilles à gaz - Verbindung von Ventilen mit Gasflaschen - Teil 2:
Partie 2: Calibres de contrôle (ISO 11363-2:2017) Prüflehren (ISO 11363-2:2017)
This European Standard was approved by CEN on 10 September 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11363-2:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 11363-2:2017) has been prepared by Technical Committee ISO/TC 58 “Gas
cylinders” in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2018, and conflicting national standards shall be
withdrawn at the latest by June 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11363-2:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11363-2:2017 has been approved by CEN as EN ISO 11363-2:2017 without any
modification.
INTERNATIONAL ISO
STANDARD 11363-2
Second edition
2017-10
Gas cylinders — 17E and 25E taper
threads for connection of valves to gas
cylinders —
Part 2:
Inspection gauges
Bouteilles à gaz — Filetages coniques 17E et 25E pour le
raccordement des robinets sur les bouteilles à gaz —
Partie 2: Calibres de contrôle
Reference number
ISO 11363-2:2017(E)
©
ISO 2017
ISO 11363-2:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 11363-2:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 2
4.1 Materials . 2
4.2 Thread profile . 2
4.3 Thread handedness . 4
4.4 Taper . 4
4.5 Pitch, P .4
5 Gauge dimensions . 4
6 Inspection gauges . 5
6.1 Gauges for cylinder neck thread . 5
6.1.1 Single-part plug gauges . 5
6.1.2 Two-part plug gauges, small end diameter . 6
6.1.3 Two-part plug gauges, large end diameter . 7
6.2 Gauges for valve stem thread . . 8
6.2.1 Single-part ring gauges . . 8
6.2.2 Two-part ring gauges, small end diameter . 8
6.2.3 Two-part ring gauges, large end diameter . 9
7 Check gauges .10
8 Use of inspection gauges .10
8.1 Plain gauges .10
8.2 Threaded plug gauges .10
8.3 Accept or reject criteria using plug gauges.10
8.4 Accept or reject criteria using ring gauges .11
9 Verification of inspection gauges .12
9.1 General .12
9.2 Plug gauges .13
9.3 Ring gauges .13
9.4 Use of check plug gauges .13
10 Identification .13
10.1 Inspection gauges .13
10.2 Check gauges .13
Annex A (informative) Examples of calculation for thread gauge dimensions on the large
end diameter .15
Annex B (informative) Limitation of gauging system .17
Bibliography .19
ISO 11363-2:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.