Inflatable boats - Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater (ISO 6185-3:2014)

ISO 6185-3:2014 specifies the minimum safety characteristics required for the design, materials to use, manufacture and testing of inflatable boats and rigid inflatable boats with a hull length in accordance with ISO 8666 less than 8 m with a motor power rating of 15 kW and greater.
ISO 6185:2014 is applicable to the following types of boats intended for use within the operating temperatures of -20 °C to +60 °C:
Type VII: Powered Boats (with power ≥ 15 kW) fitted with a buoyancy tube attached to the port and starboard sides, suitable for navigation in conditions of Design Categories C and D and capable of installing motor power rating of 15 kW and greater.
Type VIII: Powered Boats (with power > 75 kW) fitted with a buoyancy tube attached to the port and starboard sides, suitable for navigation in conditions of Design Category B capable of installing motor power rating of 75 kW and greater.
ISO 6185:2014 excludes single-chambered boats and boats made from unsupported materials, and is not applicable to aquatic toys and inflatable liferafts.

Aufblasbare Boote - Teil 3: Boote mit einer Rumpflänge unter 8 m mit einer Motorleistung von mindestens 15 kW (ISO 6185-3:2014)

Bateaux pneumatiques - Partie 3: Bateaux d'une longueur de coque inférieure à 8 m et d'une puissance moteur assignée supérieure ou égale à 15 kW (ISO 6185-3:2014)

L'ISO 6185-3:2014 spécifie les caractéristiques minimales de sécurité requises concernant la conception, les matériaux à utiliser, la fabrication et les essais des bateaux pneumatiques et semi-rigides d'une longueur de coque, mesurée conformément à l'ISO 8666, inférieure à 8 m et dont la puissance moteur assignée est supérieure ou égale à 15 kW.
L'ISO 6185-3:2014 s'applique aux types de bateaux suivants destinés à être utilisés dans une plage de températures d'utilisation comprise entre -20 °C et +60 °C:
Type VII: Bateaux à moteur (d'une puissance ≥15 kW) équipés de chambres de flottabilité reliées aux cotés bâbord et tribord, appropriés à une navigation en catégories de conception C et D et sur lesquels on peut installer des moteurs d'une puissance assignée supérieure ou égale à 15 kW.
Type VIII: Bateaux à moteur (d'une puissance ≥75 kW) équipés de chambres de flottabilité reliées aux cotés bâbord et tribord, appropriés à une navigation en catégories de conception B et sur lesquels on peut installer des moteurs d'une puissance assignée supérieure ou égale à 75 kW.
L'ISO 6185-3:2014 exclut les bateaux à flotteur monochambre, et les bateaux en matériaux non renforcés, et ne s'applique ni aux jouets aquatiques ni aux radeaux de survie gonflables.

Napihljivi čolni - 3. del: Čolni s trupom, krajšim od 8 m, in motorjem z močjo, večjo ali enako 15 kW (ISO 6185-3:2014)

Ta del standarda ISO 6185 določa minimalne varnostne lastnosti, zahtevane za načrtovanje, materiale za uporabo, izdelavo in preskušanje napihljivih čolnov ter napihljivih čolnov, ki imajo v spodnjem delu trupa togo enoto, z dolžino trupa (LH) manj kot 8 m (v skladu s standardom ISO 8666) in motorjem z močjo najmanj 15 kW.
Ta del standarda ISO 6185 se uporablja za naslednje tipe čolnov, namenjenih za uporabo pri delovnih temperaturah od –20 °C do 60 °C:
– tip VII: čolni na motorni pogon s plovno cevjo, pritrjeno na desno in levo stran, ki so primerni za krmarjenje v razmerah konstrukcijskih kategorij C in D z možnostjo namestitve motorja z močjo, večjo ali enako 15 kW;
– tip VIII: čolni na motorni pogon s plovno cevjo, pritrjeno na desno in levo stran, ki so primerni za krmarjenje v razmerah konstrukcijske kategorije B z možnostjo namestitve motorja z močjo, večjo ali enako 75kW.
OPOMBA 1: Splošne razvrstitve običajnih čolnov tipa VII in VIII so podane v ustreznih dodatkih A in B.
Ta del standarda ISO 6185 ne zajema enokabinskih čolnov in čolnov, izdelanih iz nepodprtih materialov ter se ne uporablja za vodne igrače in napihljive rešilne splave.
OPOMBA 2: Za plovila, ki so zajeta v direktivi o rekreacijskih plovilih (RCD) Evropske unije in opremljena z notranjim motorjem z nestandardnim vgrajenim izpušnim sistemom, je treba upoštevati zahteve glede emisij hrupa.

General Information

Status
Withdrawn
Publication Date
25-Sep-2018
Withdrawal Date
14-May-2024
Technical Committee
Drafting Committee
Current Stage

Relations

Buy Standard

Standard
EN ISO 6185-3:2018
English language
42 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN ISO 6185-3:2014
1DSLKOMLYLþROQLGHOýROQLVWUXSRPNUDMãLPRGPLQPRWRUMHP]PRþMRYHþMR
DOLHQDNRN: ,62
Inflatable boats - Part 3: Boats with a hull length less than 8 m with a motor rating of 15
kW and greater (ISO 6185-3:2014)
Aufblasbare Boote - Teil 3: Boote mit einer Rumpflänge unter 8 m mit einer Motorleistung
von mindestens 15 kW (ISO 6185-3:2014)
Bateaux pneumatiques - Partie 3: Bateaux d'une longueur de coque inférieure à 8 m et
d'une puissance moteur assignée supérieure ou égale à 15 kW (ISO 6185-3:2014)
Ta slovenski standard je istoveten z: EN ISO 6185-3:2018
ICS:
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 6185-3
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 6185-3:2014
English Version
Inflatable boats - Part 3: Boats with a hull length less than
8 m with a motor rating of 15 kW and greater (ISO 6185-
3:2014)
Bateaux pneumatiques - Partie 3: Bateaux d'une Aufblasbare Boote - Teil 3: Boote mit einer Rumpflänge
longueur de coque inférieure à 8 m et d'une puissance unter 8 m mit einer Motorleistung von mindestens 15
moteur assignée supérieure ou égale à 15 kW (ISO kW (ISO 6185-3:2014)
6185-3:2014)
This European Standard was approved by CEN on 16 April 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6185-3:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4

European foreword
The text of ISO 6185-3:2014 has been prepared by Technical Committee ISO/TC 188 “Small craft” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 6185-3:2018.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall be
withdrawn at the latest by March 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6185-3:2014.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2013/53/EU.
For relationship with EU Directive 2013/53/EU, see informative Annex ZA, which is an integral part of
this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The text of ISO 6185-3:2014 has been approved by CEN as EN ISO 6185-3:2018 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered
This European standard has been prepared under a Commission’s standardization request M/542
C(2015) 8736 final to provide one voluntary means of conforming to Essential Requirements of Directive
2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding Essential Requirements of that
Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2013/53/EU
Essential Requirements of Clause(s)/sub-clause(s) of Remarks/Notes
Directive 2013/53/EU this EN
Annex I, Part A, 1 - Watercraft design 3.12 except note 1 to entry Disregard note to Clause 3.12
categories
Annex I, Part A, 2.1 - Craft 9
identification
Annex I, Part A, 2.2 - Builder´s plate 9
Annex I, Part A, 2.3 - Protection from 6.2, 7.9, 7.14, 10
falling overboard and means of
reboarding
Annex I, Part A, 2.4 - Visibility from the 7.10
main steering position
Annex I, Part A, 2.5 - Owner´s manual 10, 11 Maintenance and repair information
shall be provided in the owner’s
manual
Annex I, Part A, 3.1 - Structure 5, 6.1, 6.2, 6.3, 6.4, 6.5, 6.6, 6.9,
6.10, 6.15, 7.6, 7.7, 7.12, 7.13, 8
Annex I, Part A, 3.2 - Stability and 7.3, 7.4 Design Category B, C and D only. Apply
freeboard EN ISO 12217 for Category A
Annex I, Part A, 3.3 - Buoyancy and 6.4, 7.4, 7.5, 7.6
flotation
Annex I, Part A, 3.4 - Openings in hull, 6.17
deck and superstructure
Annex I, Part A, 3.5 - Flooding 6.7, 7.3, 7.4, 8.5, 8.7
Annex I, Part A, 3.6 - Manufacturer's 7.1, 7.2
maximum recommended load
Annex I, Part A, 3.7 - Liferaft stowage 7.11
Annex I, Part A, 3.9 - Anchoring, 6.9
mooring and towing
Annex I, Part A, 4 - Handling 7.8, 8.3, 8.6
characteristics
Annex I, Part A, 5.1 - Engines and 6.12, 6.14
engine compartments
Annex I, Part A, 5.2 - Fuel system and 6.12, 6.13, 6.14
fuel tanks
Annex I, Part A, 5.3 - Electrical system 6.11
Annex I, Part A, 5.4 - Steering system 6.8, 7.13
Annex I, Part A, 5.5 - Gas system 6.18
Annex I, Part A, 5.6 - Fire protection 6.12, 6.16
Annex I, Part A, 5.7 - Navigation lights 6.19
Annex I, Part A, 5.8 - Discharge 6.7, 6.20
prevention and installations
facilitating the delivery
ashore of waste
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard
INTERNATIONAL ISO
STANDARD 6185-3
Second edition
2014-08-15
Inflatable boats —
Part 3:
Boats with a hull length less than 8
m with a motor rating of 15 kW and
greater
Bateaux pneumatiques —
Partie 3: Bateaux d’une longueur de coque inférieure à 8 m et d’une
puissance moteur assignée supérieure ou égale à 15 kW
Reference number
ISO 6185-3:2014(E)
©
ISO 2014
ISO 6185-3:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

ISO 6185-3:2014(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Symbols . 4
5 Structural Materials . 5
5.1 General . 5
5.2 Materials making up the flexible floor and buoyancy tube . 5
5.3 Wood . 7
5.4 Metal parts . 7
5.5 Glass-reinforced plastics . 7
5.6 Other materials . 7
5.7 Buoyant material used in foam filled buoyancy tubes . 7
6 Functional components . 8
6.1 Conditioning . 9
6.2 Fittings bonded to the flexible parts of the boat . 9
6.3 Manual lifting and carrying devices . 9
6.4 Valves (if applicable) . 9
6.5 Rowlocks and oars .10
6.6 Transom (where applicable) .11
6.7 Hull drainage .11
6.8 Remote steering system (where offered as standard or optional equipment) .11
6.9 Towing, anchoring and mooring devices .11
6.10 Seating and attachment systems (where offered as a standard or optional equipment) .11
6.11 Electrical installations (where offered as standard or optional equipment)) .12
6.12 Engin
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.