EN 10244-1:2009
(Main)Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 1: General principles
Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 1: General principles
This part of this European Standard specifies the requirements for the mass, other properties and testing of non-ferrous metal coatings on steel wire and steel wire products of circular or other cross-section.
This European Standard deals with requirements of general application and is of use for those coatings for which no particular requirements have been laid down in the following parts (2 to 6). Deviations are possible, particularly if required for well-defined products. In such cases, appropriate requirements shall be part of the relevant product standard.
Stahldraht und Drahterzeugnisse - Überzüge aus Nichteisenmetall auf Stahldraht - Teil 1: Allgemeine Regeln
Dieser Teil dieser Europäischen Norm legt Anforderungen an Masse, andere Eigenschaften und Prüfung von
Überzügen aus Nichteisenmetall auf Stahldraht und Stahldrahterzeugnissen mit rundem oder anderem
Querschnitt fest.
Die vorliegende Europäische Norm behandelt Anforderungen für die allgemeine Anwendung und gilt für
diejenigen Überzüge, für die keine besonderen Anforderungen in EN 10244-2 bis EN 10244-6 festgelegt sind.
Abweichungen sind möglich, insbesondere wenn sie für bestimmte Produkte verlangt werden. In diesen
Fällen sollten die entsprechenden Anforderungen Bestandteil der jeweiligen Produktnorm sein.
Fils et produits tréfilés en acier - Revêtements métalliques non ferreux sur fils d'acier - Partie 1 : Principes généraux
Cette partie de la présente Norme européenne spécifie les exigences en matière de masse, autres
caractéristiques et essais de revêtements métalliques non ferreux sur fils et produits tréfilés en acier de
section circulaire ou autre.
La présente Norme européenne traite des exigences d'application générale et concerne les revêtements pour
lesquels aucune exigence particulière n'a été établie dans les autres parties (2 à 6). Des dérogations sont
possibles, en particulier si elles sont nécessaires pour obtenir des produits spécifiques. Dans ce cas, des
exigences appropriées doivent être données dans la norme de produit correspondante.
Jeklena žica in žični izdelki - Neželezne kovinske prevleke na jekleni žici - 1. del: Splošna načela
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stahldraht und Drahterzeugnisse - Überzüge aus Nichteisenmetall auf Stahldraht - Teil 1: Allgemeine RegelnFils et produits tréfilés en acier - Revêtements métalliques non ferreux sur fils d'acier - Partie 1: Principes générauxSteel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 1: General principles77.140.65Jeklene žice, jeklene vrvi in verigeSteel wire, wire ropes and link chains25.220.40Kovinske prevlekeMetallic coatingsICS:Ta slovenski standard je istoveten z:EN 10244-1:2009SIST EN 10244-1:2009en,de01-junij-2009SIST EN 10244-1:2009SLOVENSKI
STANDARDSIST EN 10244-1:20021DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10244-1April 2009ICS 25.220.40; 77.140.65Supersedes EN 10244-1:2001
English VersionSteel wire and wire products - Non-ferrous metallic coatings onsteel wire - Part 1: General principlesFils et produits tréfilés en acier - Revêtements métalliquesnon ferreux sur fils d'acier - Partie 1 : Principes générauxStahldraht und Drahterzeugnisse - Überzüge ausNichteisenmetall auf Stahldraht - Teil 1: Allgemeine RegelnThis European Standard was approved by CEN on 13 December 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10244-1:2009: ESIST EN 10244-1:2009
Part 3: Aluminium coatings
Part 4: Tin coatings
Part 5: Nickel coatings Part 6: Copper, bronze or brass coatings According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.