EN 2033:2017
(Main)Aerospace series - Strips, cold rolled in steel, Thickness 0,1 mm ≤ a ≤ 2,5 mm - Dimensions
Aerospace series - Strips, cold rolled in steel, Thickness 0,1 mm ≤ a ≤ 2,5 mm - Dimensions
This European Standard specifies the dimensions and tolerances of:
Strips, cold rolled
in steel
Thickness 0,1 mm ≤ a ≤ 2,5 mm
for aerospace applications.
Luft- und Raumfahrt - Bänder, kaltgewalzt aus Stahl, Dicken 0,1 mm ≤ a ≤ 2,5 mm - Maße
Série aérospatiale - Bandes, laminées à froid en acier, Èpaisseurs 0,1 mm ≤ a ≤ 2,5 mm - Dimensions
Aeronavtika - Trakovi iz hladno valjenega jekla - Debelina 0,1 mm ≤ a ≤ 3 mm - Mere
Ta evropski standard določa zahteve glede mer in toleranc za:
trakove iz hladno valjanega
jekla
debeline 0,1 mm ≤ a ≤ 2,5 mm
za uporabo v aeronavtiki.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.0HUH0D‰H'LPHQVLRQV49.025.10JeklaSteelsICS:Ta slovenski standard je istoveten z:EN 2033:2017SIST EN 2033:2017en,fr,de01-maj-2017SIST EN 2033:2017SLOVENSKI
STANDARD
SIST EN 2033:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2033
March
t r s y ICS
v {ä r t wä s r English Version
Aerospace series æ Stripsá cold rolled in steelá Thickness
rá s mm a
tá w mm æ Dimensions Sßrie aßrospatiale æ Bandesá laminßes à froid en acierá Èpaisseurs
rá s mm a
tá w mm æ Dimensions
Luftæ und Raumfahrt æ Bänderá kaltgewalzt aus Stahál Dicken
rá s mm a
tá w mm æ Maße This European Standard was approved by CEN on
t s November
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
t r u uã t r s y ESIST EN 2033:2017
EN 2033:2017 (E) 2 Contents
Page European foreword . 3 Introduction. 4 1 Scope .
w 2 Normative references .
w 3 Form .
w 4 Recommended dimensions and mass . 6
w Dimensional tolerances. 7
wä s Thickness . 7
wä t Width .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.