Plastics - Quality recommendations and basis for specifications for application of plastic recyclates in products - Part 4 : Poly(ethylene terephtalate) (PET)

This document provides relevant characteristics and typical values for PET recyclates intended for groups of defined applications (the product families).
The relevant characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer's defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in the Annex A.
NOTE 2   The selection of relevant properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

Kunststoffe - Qualitätsempfehlungen und Grundlagen für Spezifikationen für die Verwendung von Kunststoffrezyklaten in Produkten - Teil 4: Poly(ethylenterephtalat) (PET)

Dieses Dokument enthält relevante Eigenschaften und typische Werte für Rezyklate aus Polyethylenterephthalat (PET), die für Gruppen von definierten Anwendungen (die Produktfamilien) vorgesehen sind.
Die relevanten Eigenschaften und typischen Werte für die verschiedenen Produktfamilien leiten sich aus den Leistungsanforderungen der zu dieser Familie gehörenden Produkte ab, einschließlich der Anforderungen an die Produktherstellungsprozesse, sofern zutreffend.
Dieses Dokument gilt für Kunststoff-Rezyklate, die für die Herstellung von (Zwischen-)Produkten vorgesehen sind.
Dieses Dokument ist zur Verwendung in Verbindung mit Teil 1 dieser Normenreihe vorgesehen, in dem das Bezeichnungssystem für Kunststoff-Rezyklate beschrieben wird. Das Bezeichnungssystem ermöglicht den Vergleich zwischen recyceltem und neuem Material auf der Ebene der kennzeichnenden Eigenschaften des Polymers.
ANMERKUNG 1   Beispiele für Bezeichnungen von Kunststoff-Rezyklaten sind in Anhang A aufgeführt.
ANMERKUNG 2   Die Auswahl der relevanten Eigenschaften für eine Produktfamilie basiert auf EN ISO 10350 1, erweitert um spezifische Eigenschaften für Kunststoff-Rezyklate.

Plastiques - Recommandations qualité et base de spécification pour l’application des recyclats de plastiques dans les produits - Partie 4 : Poly(éthylène téréphtalate) (PET)

Le présent document fournit des caractéristiques pertinentes et des valeurs types pour les recyclats de PET destinés à être utilisés pour des groupes d’applications définies (les familles de produits).
Les caractéristiques pertinentes et les valeurs types pour les différentes familles de produits sont issues des exigences de performance des produits appartenant à cette famille, y compris les exigences pour les processus de fabrication des produits, le cas échéant.
Le présent document s’applique aux recyclats de plastiques destinés à être utilisés pour la fabrication de produits (intermédiaires).
Le présent document est destiné à être utilisé conjointement avec la Partie 1 de cette série de normes, qui décrit le système de désignation des recyclats de plastiques. Le système de désignation permet de comparer les matériaux recyclés et vierges au niveau des propriétés de désignation définies pour le polymère.
NOTE 1   Des exemples de désignations des recyclats de plastiques sont donnés dans l’Annexe A.
NOTE 2   La sélection des propriétés pertinentes pour les recyclats doit être basée sur l’EN ISO 10350 1, et étendue avec des propriétés spécifiques liées aux recyclats de plastiques.

Polimerni materiali - Priporočila za kakovost in podlaga za specifikacije za uporabo polimernih reciklatov v izdelkih - 4. del: Poli(etilen tereftalat) (PET)

General Information

Status
Not Published
Publication Date
15-May-2025
Technical Committee
Current Stage
4060 - Closure of enquiry - Enquiry
Start Date
16-May-2024
Due Date
22-Mar-2024
Completion Date
16-May-2024

Buy Standard

Draft
prEN 18064-4:2024
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-2024
Polimerni materiali - Priporočila za kakovost in podlaga za specifikacije za
uporabo polimernih reciklatov v izdelkih - 4. del: Poli(etilen tereftalat) (PET)
Plastics - Quality recommendations and basis for specifications for application of plastic
recyclates in products - Part 4 : Poly(ethylene terephtalate) (PET)
Kunststoffe - Qualitätsempfehlungen und Grundlagen für Spezifikationen für die
Verwendung von Kunststoffrezyklaten in Produkten - Teil 4: Poly(ethylenterephtalat)
(PET)
Plastiques - Recommandations qualité et base de spécification pour l’application des
recyclats de plastiques dans les produits - Partie 4 : Poly(éthylène téréphtalate) (PET)
Ta slovenski standard je istoveten z: prEN 18064-4
ICS:
13.030.50 Recikliranje Recycling
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2024
ICS 13.030.50; 83.080.01; 83.140.01
English Version
Plastics - Quality recommendations and basis for
specifications for application of plastic recyclates in
products - Part 4 : Poly(ethylene terephtalate) (PET)
Kunststoffe - Qualitätsempfehlungen und Grundlagen
für Spezifikationen für die Verwendung von
Kunststoffrezyklaten in Produkten - Teil 5:
Poly(ethylenterephtalat) (PET)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 249.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 18064-4:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and abbreviations . 6
3.1 Terms and definitions . 6
3.2 Abbreviations . 6
4 Categorization of Polyethylene terephthalate (PET) applications and requirements . 6
5 Selection of relevant properties for Polyethylene terephthalate (PET) recyclates. 7
6 Typical range for characteristics of product families . 7
7 Designation of Polyethylene terephthalate (PET) recyclates . 7
Annex A (informative) Designatory properties Polyethylene terephthalate recyclate . 8
A.1 Generic and additional designatory properties . 8
A.2 Designation of Polyethylene terephthalate recyclate . 8
A.2.1 General. 8
A.2.2 Data block 1 . 8
A.2.3 Data block 2 . 9
A.2.4 Data block 3 . 9
A.2.5 Data block 4 . 9
A.2.5.1 General. 9
A.2.5.2 Viscosity number . 9
A.2.5.3 Tensile modulus of elasticity . 11
A.2.6 Data block 5 . 11
A.2.7 Designation examples . 13
A.2.7.1 First designation example from EN ISO 20028-1 . 13
A.2.7.2 Further designation examples . 13
Annex B (normative) Typical values for product families . 15
B.1 Typical values . 15
Bibliography . 20

European foreword
This document (prEN 18064-4:2024) has been prepared by Technical Committee CEN/TC 249
“Plastics”, the secretariat of which is held by SIS.
This document is currently submitted to the CEN Enquiry.
This document is part of the prEN 18064-series, currently consisting of all parts as listed below. This
series of standards consist of a general part 1, and material specific parts for different types of plastics.
This particular part covers typical values (ranges, or min/max values) for Polyethylene terephthalate
(PET) general purpose plastics, that can be composed of 100 % recyclates (mechanical and/or
chemical), or a combination of recyclates and virgin plastic.
This part is supported by other standards on test methods to which references are made throughout
this document.
EN 18064, Plastics — Quality recommendations and basis for specifications for application of plastic
recyclates in products, is currently composed with the following parts:
— Part 1: General aspects
— Part 2: Polyethylene (PE)
— Part 3: Polypropylene (PP)
— Part 4: Poly(ethylene terephthalate) (PET)
— Part 5: Poly(vinyl chloride) (PVC)
— Part 6: Polystyrene (PS)
— Part 7: Acrylonitrile-butadiene-styrene (ABS)
NOTE Part 6 for PS also includes EPS and XPS.
Introduction
See prEN 18064-1.
1 Scope
This document provides relevant characteristics and typical values for PET recyclates intended for
groups of defined applications (the product families).
The relevant characteristics and typical values for the different product families are derived from the
performance requirements of the products belonging to that family, including requirements for product
manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate)
products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes
the designation system for plastic recyclates. The designation system allows comparison between
recycled and virgin material at the level of the polymer's defined designatory properties.
NOTE 1 Examples of designations of plastic recyclates are given in the Annex A.
NOTE 2 The selection of relevant properties for a product family is based on EN ISO 10350-1, extended with
specific properties related to plastic recyclates.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
prEN 18065 , Plastics — Recycled Plastics — Classification of recycled plastics based on Data Quality
Levels for use and (digital) trading
CEN/TR 15353, Plastics - Recycled plastics - Guidelines for the development of standards for recycled
plastics
prEN 18064-1 , Plastics — Quality recommendations and basis for specifications for application of plastic
recyclates in products — Part 1: General aspects (under preparation)
EN 15348, Plastics - Recycled plastics - Characterization of poly(ethylene terephthalate) (PET) recyclates
EN ISO 60, Plastics - Determination of apparent density of material that can be poured from a specified
funnel (ISO 60)
EN ISO 472:2013, Plastics - Vocabulary (ISO 472)
EN ISO 1043-1, Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special
characteristics (ISO 1043-1)
EN ISO 1133-2, Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate
(MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or
moisture (ISO 1133-2)
EN ISO 1628-5, Plastics - Determination of the viscosity of polymers in dilute solution using capillary
viscometers - Part 5: Thermoplastic polyester (TP) homopolymers and copolymers (ISO 1628-5)

Under preparation.
Under preparation.
EN ISO 11357-3, Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature
and enthalpy of melting and crystallization (ISO 11357-3)
EN ISO 14021, Environmental labels and declarations – Self-declared environmental claims (Type II
environmental labelling) (ISO 14021)
EN ISO 15512, Plastics - Determination of water content (ISO 15512:2019)
EN ISO 20028-2, Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2:
Preparation of test specimens and determination of properties (ISO 20028-2)
ASTM D1895, Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic
Materials
ASTM F2013, Standard Test Method for Determination of Residual Acetaldehyde in Polyethylene
Terephthalate Bottle Polymer Using an Automated Static Head-Space Sampling Device and a Capillary GC
with a Flame Ionization Detector
ASTM D4603, Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate)
(PET) by Glass Capillary Viscometer
ASTM D6980-12, Standard Test Method for Determination of Moisture in Plastics by Loss in Weight
3 Terms, definitions and abbreviations
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 472:2013 and
CEN/TR 15353 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1.1
typical value
indicative value intended for first contact, e. g. between converter and recycler
Note 1 to entry: Final values to be agreed e.g. between converter and recycler.
3.2 Abbreviations
For the purposes of this document, abbreviated terms related to recyclates given in EN ISO 1043-1 and
prEN 18064-1 apply.
4 Categorization of Polyethylene terephthalate (PET) applications and
requirements
The product families in combination with the relevant converting technologies are given in the
dedicated annexes. In here description is given of the intended use(s) of these product families (for
example impact resistant application), and for which products can these be used (e.g. containers, sheet
materials).
5 Selection of releva
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.