EN ISO 17782:2018

Petroleum, petrochemical and natural gas industries - Scheme for conformity assessment of manufacturers of special materials (ISO 17782:2018)

This document establishes a procedure for verifying that the manufacturer of special materials for the petroleum, petrochemical and natural gas industries has sufficient competence and experience of the relevant material grades of metal, and the necessary facilities and equipment, to manufacture these materials in the required shapes and sizes with acceptable properties according to the applicable standard, material specification and/or material data sheet specified by the purchaser.
This document is applicable to manufacturers of various materials, product forms and manufacturing processes when specified by the purchaser. This document has been established considering especially, but not exclusively:
a)    duplex stainless steel;
b)    high alloyed austenitic stainless steel;
c)    nickel-based alloys;
d)    titanium and its alloys.
This document is also applicable to the processes of induction bending and strain-hardened products.

Erdöl-, petrochemische und Erdgasindustrie - Herstellerqualifizierung von Sonderwerkstoffen (ISO 17782:2018)

Industries du pétrole, de la pétrochimie et du gaz naturel - Système d'évaluation de la conformité des fabricants de matériaux spéciaux (ISO 17782:2018)

Le présent document établit un mode opératoire afin de vérifier que le fabricant de matériaux spéciaux destinés aux industries pétrolière, pétrochimique et du gaz naturel dispose d'un niveau de compétence et d'expérience suffisant en matière de qualité des métaux et qu'il possède les installations et l'équipement nécessaires à leur fabrication dans les formes et dimensions exigées, avec des propriétés acceptables conformément à la norme applicable, à la spécification du matériau et/ou à la fiche technique du matériau spécifiée par l'acheteur.
Le présent document est applicable aux fabricants de divers matériaux, des formes de produits et des processus de fabrication lorsque l'acheteur le précise. Le présent document a été établi en prenant notamment en compte, sans toutefois s'y limiter:
a)    l'acier inoxydable duplex;
b)    l'acier austénitique inoxydable fortement allié;
c)    les alliages à base de nickel;
d)    le titane et ses alliages.
Le présent document est également applicable aux processus des produits obtenus par cintrage par induction et par écrouissage.

Petrokemična industrija ter industrija za predelavo nafte in zemeljskega plina - Shema za ugotavljanje skladnosti proizvajalcev posebnih materialov (ISO 17782:2018)

Ta dokument določa postopek za preverjanje, ali ima proizvajalec posebnih materialov v naftni industriji, petrokemični industriji in industriji zemeljskega plina dovolj kompetenc in izkušenj z ustreznimi vrstami kovin ter potrebnimi napravami in opremo za proizvodnjo
teh materialov v zahtevanih oblikah in velikostih s sprejemljivimi lastnostmi v skladu z ustreznim
standardom, specifikacijo materiala in/ali tehničnim listom materiala, ki ga določi kupec.
Ta dokument se uporablja za proizvajalce različnih materialov, oblik izdelkov in proizvodnih
procesov, ki jih določi kupec. Ta dokument je bil oblikovan posebej,
a ne izključno za:
a) dupleksno nerjavno jeklo;
b) avstenitno visoko legirano nerjavno jeklo;
c) nikljeve litine;
d) titan in njegove zlitine.
Ta dokument se uporablja tudi za postopke induktivnega utrjevanja in deformacijsko utrjene izdelke.

General Information

• Status: Published
• Publication Date: 27-Nov-2018
• Withdrawal Date: 30-May-2019
• ICS: 75.020 - Extraction and processing of petroleum and natural gas
• ICS: 75.180.01 - Equipment for petroleum and natural gas industries in general
• ICS: 77.020 - Production of metals
• Technical Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Drafting Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 28-Nov-2018
• Due Date: 02-Jan-2015
• Completion Date: 28-Nov-2018
• Ref Project: SIST EN ISO 17782:2019 - Petroleum, petrochemical and natural gas industries - Scheme for conformity assessment of manufacturers of special materials (ISO 17782:2018)

Standards Content (Sample)

SLOVENSKI STANDARD
01-februar-2019
3HWURNHPLþQDLQGXVWULMDWHULQGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD
6KHPD]DXJRWDYOMDQMHVNODGQRVWLSURL]YDMDOFHYSRVHEQLKPDWHULDORY,62

Petroleum, petrochemical and natural gas industries - Scheme for conformity
assessment of manufacturers of special materials (ISO 17782:2018)
Erdöl-, petrochemische und Erdgasindustrie - Herstellerqualifizierung von
Sonderwerkstoffen (ISO 17782:2018)
Industries du pétrole, de la pétrochimie et du gaz naturel - Système d'évaluation de la
conformité des fabricants de matériaux spéciaux (ISO 17782:2018)
Ta slovenski standard je istoveten z: EN ISO 17782:2018
ICS:
75.180.01 Oprema za industrijo nafte in Equipment for petroleum and
zemeljskega plina na splošno natural gas industries in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 17782
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2018
EUROPÄISCHE NORM
ICS 75.020
English Version
Petroleum, petrochemical and natural gas industries -
Scheme for conformity assessment of manufacturers of
special materials (ISO 17782:2018)
Industries du pétrole, de la pétrochimie et du gaz Erdöl-, petrochemische und Erdgasindustrie -
naturel - Système d'évaluation de la conformité des Herstellerqualifizierung von Sonderwerkstoffen (ISO
fabricants de matériaux spéciaux (ISO 17782:2018) 17782:2018)
This European Standard was approved by CEN on 27 September 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17782:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 17782:2018) has been prepared by Technical Committee ISO/TC 67 "Materials,
equipment and offshore structures for petroleum, petrochemical and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for
petroleum, petrochemical and natural gas industries” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2019, and conflicting national standards shall be
withdrawn at the latest by May 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 17782:2018 has been approved by CEN as EN ISO 17782:2018 without any modification.

INTERNATIONAL ISO
STANDARD 17782
First edition
2018-10
Petroleum, petrochemical and
natural gas industries — Scheme
for conformity assessment of
manufacturers of special materials
Industries du pétrole, de la pétrochimie et du gaz naturel — Système
d'évaluation de la conformité des fabricants de matériaux spéciaux
Reference number
ISO 17782:2018(E)
©
ISO 2018
ISO 17782:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 17782:2018(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms . 2
3.1 Terms and definitions . 2
3.2 Abbreviated terms . 4
4 Responsibilities . 5
4.1 Purchaser's responsibilities . 5
4.2 Manufacturer’s responsibilities . 5
4.3 Qualifying Company’s responsibilities . 5
5 Conformity assessment of manufacturers . 6
5.1 Conformity assessment . 6
5.2 Basis for assessment of manufacturers . 6
5.3 Evaluation for conformity. 7
5.4 Review of manufacturing procedure conformity record (MPCR) . 7
5.5 Statement of conformity . 7
6 Validity of the manufacturer procedure conformity record (MPCR) .7
6.1 Term of validity . 7
6.2 Renewal of the MPCR. 7
6.3 Transitional requirements . 8
7 General requirements . 8
7.1 Knowledge and relevant experience . 8
7.1.1 Knowledge . 8
7.1.2 Relevant experience . 8
7.2 Manufacturing facilities and equipment . 8
7.3 Subcontractors and suppliers . 8
7.4 Quality requirements for test laboratories and manufacturers of welded products . 9
7.4.1 Test laboratories . 9
7.4.2 Manufacturers of welded products . 9
8 Manufacturing procedure summary (MPS) . 9
8.1 General . 9
8.2 Content of the manufacturing procedure summary (MPS) . 9
8.2.1 Scope of the manufacturing procedure summary . 9
8.2.2 Manufacturing procedure summary requirements .10
9 Heat treatment .12
9.1 Facilities and equipment .12
9.1.1 General.12
9.1.2 Foundries.12
9.1.3 Heat treatment furnaces .12
9.1.4 Thermocouples and pyrometers .13
9.1.5 Quenching baths . .13
9.1.6 Loading of components .13
9.1.7 Transfer time between furnace and quenching bath .13
9.1.8 Continuous, semi-continuous and induction furnaces .13
9.2 Heat treatment procedure .14
9.2.1 General.14
9.2.2 Heat
...