FprEN 16732
(Main)Slide fasteners (zips) - Specification
Slide fasteners (zips) - Specification
This document specifies performance levels and test methods for the following characteristics of slide fasteners made from interlocking components mounted on tapes: strengths of puller attachment, closed-end slide fastener bottom stop, top stop, open-end slide fastener box, reciprocating mechanism, closed slide fastener when extended laterally, open-end attachment when extended laterally, slider locking device, and open-end slide fastener single stringer slider retention and slider resistance to torque.
NOTE The tests specified in Annexes B to K have been specifically devised to permit their direct application to finished slide fasteners with a view to giving the user reasonable assurance that a slide fastener conforming to the requirements of this standard can satisfactorily fulfil its intended purpose. Annex L gives information about sampling procedures for bulk quantities of slide fasteners.
In addition, performance levels are also specified for colour fastness to washing, dry cleaning and water, and for dimensional stability to washing and dry cleaning.
This document is applicable to all different types of slide fasteners for general use and is not applicable to slide fasteners for specialist purposes (for example: pressure sealed slide fasteners for diving suits).
Reißverschlüsse - Spezifikation
Fermetures à glissière - Spécifications
Patentne zadrge - Specifikacija
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2024
Patentne zadrge - Specifikacija
Slide fasteners (zips) - Specification
Reißverschlüsse - Spezifikation
Fermetures à glissière - Spécifications
Ta slovenski standard je istoveten z: prEN 16732
ICS:
61.040 Pokrivala. Dodatki k Headgear. Clothing
oblačilom. Spenjanje oblačil accessories. Fastening of
clothing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
prEN 16732
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2024
ICS Will supersede EN 16732:2015
English Version
Slide fasteners (zips) - Specification
Fermetures à glissière - Spécifications Reißverschlüsse - Spezifikation
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 248.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16732:2024 E
worldwide for CEN national Members.
prEN 16732:2024 (E)
Contents Page
European foreword . 5
Introduction . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Requirements . 10
5 Conditioning and testing . 13
5.1 Conditioning of test samples . 13
5.2 Slide fasteners measurements . 13
5.3 Strength of puller attachment . 14
5.4 Strength of closed-end . 14
5.5 Strength of top stop . 14
5.6 Strength of open-end slide fastener box . 14
5.7 Resistance to reciprocation. 14
5.8 Lateral strength of slide fastener . 15
5.9 Lateral strength of open-end attachment . 15
5.10 Strength of slider locking device . 15
5.11 Open-end slide fastener single stringer slider retention . 15
5.12 Torque strength. 15
6 Washing and dry cleaning test . 15
7 Test report . 15
8 Marking . 16
Annex A (informative) Guidance on factors to be taken into consideration when specifying
slide fasteners . 20
A.1 General. 20
Annex B (normative) Test for strength of puller attachment . 21
B.1 Principle . 21
B.2 Apparatus . 21
B.3 Procedure . 21
Annex C (normative) Test for strength of closed-end . 22
C.1 Principle . 22
C.2 Apparatus . 22
C.3 Procedure . 23
Annex D (normative) Test for strength of top stop . 24
D.1 Principle . 24
D.2 Apparatus . 24
prEN 16732:2024 (E)
D.3 Procedure . 26
Annex E (normative) Test for strength of open-end slide fastener box . 27
E.1 Principle . 27
E.2 Apparatus . 27
E.3 Procedure . 28
Annex F (normative) Test for resistance to reciprocation . 29
F.1 Principle . 29
F.2 Apparatus . 29
F.3 Procedure . 30
Annex G (normative) Test for lateral strength of slide fastener . 32
G.1 Principle . 32
G.2 Apparatus . 32
G.3 Procedure . 32
Annex H (normative) Test for lateral strength of open-end attachment . 33
H.1 Principle . 33
H.2 Apparatus . 33
H.3 Procedure . 33
Annex I (normative) Test for strength of slider locking device . 34
I.1 Principle . 34
I.2 Apparatus . 34
I.3 Procedure . 34
Annex J (normative) Test for open-end slide fastener single stringer slider retention . 35
J.1 Principle . 35
J.2 Apparatus . 35
J.3 Procedure . 35
Annex K (normative) Torque test . 36
K.1 Principle . 36
K.2 Apparatus . 36
K.3 Procedure . 37
K.4 Test to failure method for quality control . 37
Annex L (informative) Sampling procedures for bulk quantities of slide fasteners . 39
L.1 General . 39
L.2 Guidance on interpretation of results for acceptance purposes . 39
L.3 Guide to changing from normal to tightened test procedures . 39
Annex M (informative) End-uses and performance codes for labelling purposes . 40
Annex N (Informative) Test for resistance to reciprocation for slide fasteners with length
from 75 mm to 200 mm . 41
prEN 16732:2024 (E)
N.1 Principle . 41
N.2 Apparatus . 41
N.3 Preparation of test specimens . 42
N.4 Procedure
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.