Advanced technical ceramics - Monolithic ceramics. Thermo-physical properties - Part 3: Determination of specific heat capacity

This document specifies two methods for the determination of specific heat capacity of advanced monolithic technical ceramic materials based on drop calorimetry (Method A) and differential scanning calorimetry (DSC, Method B) over a temperature range from room temperature upwards, depending on the design of the equipment.
NOTE 1   The methods described apply in the case of test materials free from phase transformations, annealing effects or partial melting. If any such effect occurs in a material over the temperature range of the test, spurious results will be obtained unless the data are carefully analysed. In such cases it is usually necessary to conduct repeat tests at a number of temperatures close to the discontinuity, in order to estimate correctly its contribution to the apparent heat capacity.
NOTE 2   Care should be exercised in both methods over the selection of the cell or crucible material and in the selection of the test atmosphere, especially at high temperatures. Test pieces can react with the crucible or the atmosphere, leading to spurious results. In general, an awareness of such problems should be maintained at all times. Especially with regard to Method B, awareness should also be maintained of radiation effects at temperatures above 1000 °C, and of the reproducibility of the output signal.

Hochleistungskeramik - Monolithische Keramik - Thermophysikalische Eigenschaften - Teil 3: Bestimmung der spezifischen Wärmekapazität

Dieses Dokument legt zwei Verfahren zur Bestimmung der spezifischen Wärmekapazität monolithischer Hochleistungskeramik fest, die auf der Fallkalorimetrie (Verfahren A) und der dynamischen Differenz-Kalorimetrie (DDK, Verfahren B) beruhen; dabei werden Temperaturbereiche von Raumtemperatur an steigend bis zu einer gerätebedingten Endtemperatur abgedeckt.
ANMERKUNG 1   Die festgelegten Verfahren gelten für den Fall, dass die zu prüfenden Werkstoffe keine Phasenumwandlungen, keine Erholungseffekte oder partielle Aufschmelzungen durchmachen. Falls ein Werkstoff einen solchen Effekt im Temperaturbereich der Prüfung zeigt, werden falsche Ergebnisse erhalten, es sei denn, die Werte wurden sorgfältig analysiert. In solchen Fällen ist es üblicherweise notwendig, bei mehreren Temperaturen nahe der Transformationstemperatur Wiederholungsmessungen durchzuführen, um so exakt den Beitrag zu der scheinbaren Wärmekapazität abschätzen zu können.
ANMERKUNG 2   Die Art des Werkstoffes der Messzelle bzw. des Tiegels und die Art der Prüfatmosphäre sollten sachkundig festgelegt werden, insbesondere bei Hochtemperaturmessungen. Proben können sowohl mit dem Tiegel als auch der Atmosphäre reagieren, was zu falschen Ergebnissen führt. Im Allgemeinen sollte jederzeit mit solchen Problemen gerechnet werden. Besonders im Hinblick auf Verfahren B sollte bei Temperaturen über 1 000 °C die Aufmerksamkeit auf Strahlungseffekte und die Reproduzierbarkeit des Messsignals gelenkt werden.

Céramiques techniques avancées - Céramiques monolithiques. Propriétés thermophysiques - Partie 3 : Détermination de la chaleur spécifique

Sodobna tehnična keramika - Monolitna keramika - Termofizikalne lastnosti - 3. del: Ugotavljanje posebne toplotne kapacitete

General Information

Status
Published
Publication Date
18-Jan-2005
Withdrawal Date
30-Jul-2005
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
17-Mar-2020

Relations

Buy Standard

Standard
EN 821-3:2005
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 821-3:2005
01-maj-2005
1DGRPHãþD
SIST ENV 821-3:2000
6RGREQDWHKQLþQDNHUDPLND0RQROLWQDNHUDPLND7HUPRIL]LNDOQHODVWQRVWL
GHO8JRWDYOMDQMHSRVHEQHWRSORWQHNDSDFLWHWH
Advanced technical ceramics - Monolithic ceramics. Thermo-physical properties - Part 3:
Determination of specific heat capacity
Hochleistungskeramik - Monolithische Keramik - Thermophysikalische Eigenschaften -
Teil 3: Bestimmung der spezifischen Wärmekapazität
Céramiques techniques avancées - Céramiques monolithiques. Propriétés
thermophysiques - Partie 3 : Détermination de la chaleur spécifique
Ta slovenski standard je istoveten z: EN 821-3:2005
ICS:
81.060.30 Sodobna keramika Advanced ceramics
SIST EN 821-3:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 821-3:2005

---------------------- Page: 2 ----------------------

SIST EN 821-3:2005



EUROPEAN STANDARD
EN 821-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
January 2005
ICS 81.060.99 Supersedes ENV 821-3:1993
English version
Advanced technical ceramics - Monolithic ceramics. Thermo-
physical properties - Part 3: Determination of specific heat
capacity
Céramiques techniques avancées - Céramiques Hochleistungskeramik - Monolithische Keramik -
monolithiques. Propriétés thermophysiques - Partie 3 : Thermophysikalische Eigenschaften - Teil 3: Bestimmung
Détermination de la chaleur spécifique der spezifischen Wärmekapazität
This European Standard was approved by CEN on 9 December 2004.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.




EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 821-3:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 821-3:2005
EN 821-3:2005 (E)
Contents
Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Method A – Drop calorimetry.5
5 Method B – Differential scanning calorimetry (DSC) .8
6 Report .10
Bibliography .18

2

---------------------- Page: 4 ----------------------

SIST EN 821-3:2005
EN 821-3:2005 (E)
Foreword
This document (EN 821-3:2005) has been prepared by Technical Committee CEN/TC 184 “Advanced
technical ceramics”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2005, and conflicting national standards shall be withdrawn at
the latest by August 2005.
EN 821 Advanced technical ceramics — Monolithic ceramics - Thermo-physical properties consists of the
following parts:
Part 1: Determination of thermal expansion
Part 2: Determination of thermal diffusivity by
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.