EN ISO 11299-2:2018
(Main)Plastics piping systems for renovation of underground gas supply networks - Part 2: Lining with continuous pipes (ISO 11299-2:2018)
Plastics piping systems for renovation of underground gas supply networks - Part 2: Lining with continuous pipes (ISO 11299-2:2018)
This document, read in conjunction with ISO 11299-1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground gas supply networks. It is applicable to polyethylene (PE) pipes of three different types:
— PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes;
— PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating;
— Coated PE pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe ("coated pipe"), as described in Annex A.
In addition it covers:
— jointing of pipe lengths by means of butt fusion;
— fabricated and injection-moulded fittings made of PE;
It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature.
NOTE For other operating temperatures, guidance is given in ISO 4437-5:2014.
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten Gasversorgungsnetzwerken - Teil 2: Rohrstrang-Lining (ISO 11299-2:2018)
Dieses Dokument legt die Anforderungen und Prüfverfahren für Rohre und Formstücke fest, die Teil von Kunststoff-Rohrleitungssystemen sind, die im Rahmen der Renovierung von erdverlegten Gasversorgungsnetzwerken als Rohrstränge eingebaut werden; es wird im Zusammenhang mit ISO 11299 1 angewendet. Dieses Dokument gilt für Rohre aus Polyethylen (PE) drei verschiedener Arten:
— einschichtige PE-Vollwandrohre (Nenn-Außendurchmesser dn), einschließlich aller Kennzeichnungs-streifen;
— PE-Rohre mit koextrudierten Schichten auf der Innen- und/oder Außenseite des Rohrs (Gesamt-Außendurchmesser dn), wie in Anhang A festgelegt, wobei alle Schichten dieselbe MRS-Stufe aufweisen;
— beschichtete PE-Rohre (Außendurchmesser dn), die eine zusätzliche abziehbare, angrenzende, thermoplastische Schicht auf der Außenseite des Rohrs aufweisen („beschichtetes Rohr“), wie in Anhang A beschrieben.
Dieses Dokument deckt außerdem Folgendes ab:
— Herstellen von Verbindungen zwischen Rohrstücken mittels Stumpfschweißen;
— vorgefertigte Formstücke und Spritzguss-Formstücke aus PE.
Es gilt für Rohre, Formstücke und Baugruppen aus PE, die für die Verwendung bei einer Betriebstemperatur von 20 °C als Referenztemperatur vorgesehen sind.
ANMERKUNG ISO 4437 5:2014 enthält Vorgaben für andere Betriebstemperaturen.
Systèmes de canalisations en plastique pour la rénovation des réseaux enterrés de distribution de gaz - Partie 2: Tubage par tuyau continu avec espace annulaire (ISO 11299-2:2018)
Le présent document, lu conjointement avec l'ISO 11299‑1, spécifie les exigences et les méthodes d'essai pour des tuyaux et raccords qui font partie des systèmes de canalisations en plastique installés sous forme de tuyaux continus utilisés pour la rénovation des réseaux enterrés de distribution de gaz. Il s'applique aux tuyaux en polyéthylène (PE) de trois types différents:
— tuyaux en PE monocouches à paroi compacte (diamètre extérieur nominal, dn), y compris les bandes d'identification éventuelles;
— tuyaux en PE avec des couches co-extrudées à l'extérieur et/ou à l'intérieur du tuyau (diamètre extérieur total, dn), tels que spécifiés dans l'Annexe A, toutes les couches ayant la même classification MRS;
— tuyaux en PE revêtus (diamètre extérieur, dn) comportant une couche thermoplastique supplémentaire pelable et contiguë à l'extérieur du tuyau (« tuyau revêtu »), tel que décrit à l'Annexe A.
Il couvre également:
— l'assemblage des longueurs de tuyau par soudage bout à bout;
— les raccords en PE façonnés et moulés par injection.
Il s'applique aux tuyaux, raccords et montages en PE destinés à être utilisés à une température de fonctionnement de 20 °C, qui est la température de référence.
NOTE Pour d'autres températures de service, des lignes directrices sont données dans l'ISO 4437-5:2014.
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo s plinom - 2. del: Oblaganje z neprekinjenimi cevmi (ISO 11299-2:2018)
Ta dokument, bran v povezavi s 1. delom, določa zahteve in preskusne metode za cevi in fitinge, ki so del plastičnih cevnih sistemov, nameščenih kot neprekinjene cevi pri obnovi podzemnih omrežij za oskrbo s plinom. Velja za polietilenske cevi (PE) treh različnih tipov: polietilenske trdne stenske cevi iz enega sloja (nazivni zunanji premer, DN) s kakršnimi koli identifikacijskimi črtami;
polietilenske cevi s koekstrudiranimi sloji na zunanji in/ali notranji strani cevi (celotni zunanji premer, DN), kot je opredeljeno v dodatku A, pri čemer imajo vsi sloji enako oceno MRS;
cevi, prevlečene s polietilenom (zunanji premer, DN), ki imajo na zunanji strani (»prevlečena cev«) stični, termoplastični dodatni sloj,
ki ga je mogoče odluščiti, glej dodatek A.
Poleg tega zajema:
spajanje dolžin cevi s soležnim taljenjem;
izdelane in brizgano lite fitinge iz polietilena.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2019
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo s
plinom - 2. del: Oblaganje z neprekinjenimi cevmi (ISO 11299-2:2018)
Plastics piping systems for renovation of underground gas supply networks - Part 2:
Lining with continuous pipes (ISO 11299-2:2018)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten
Gasversorgungsnetzwerken - Teil 2: Rohrstrang-Lining (ISO 11299-2:2018)
Systèmes de canalisations en plastique pour la rénovation des réseaux enterrés de
distribution de gaz - Partie 2: Tubage par tuyau continu avec espace annulaire (ISO
11299-2:2018)
Ta slovenski standard je istoveten z: EN ISO 11299-2:2018
ICS:
83.140.30 3ROLPHUQHFHYLLQILWLQJL]D Plastics pipes and fittings for
VQRYLNLQLVRWHNRþLQH non fluid use
91.140.40 Sistemi za oskrbo s plinom Gas supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 11299-2
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2018
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45; 75.200
English Version
Plastics piping systems for renovation of underground gas
supply networks - Part 2: Lining with continuous pipes
(ISO 11299-2:2018)
Systèmes de canalisations en plastique pour la Kunststoff-Rohrleitungssysteme für die Renovierung
rénovation des réseaux enterrés de distribution de gaz von erdverlegten Gasversorgungsnetzwerken - Teil 2:
- Partie 2: Tubage par tuyau continu avec espace Rohrstrang-Lining (ISO 11299-2:2018)
annulaire (ISO 11299-2:2018)
This European Standard was approved by CEN on 18 October 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11299-2:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 11299-2:2018) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2019, and conflicting national standards shall be
withdrawn at the latest by June 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11299-2:2018 has been approved by CEN as EN ISO 11299-2:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 11299-2
First edition
2018-10
Plastics piping systems for renovation
of underground gas supply
networks —
Part 2:
Lining with continuous pipes
Systèmes de canalisations en plastique pour la rénovation des réseaux
enterrés de distribution de gaz —
Partie 2: Tubage par tuyau continu avec espace annulaire
Reference number
ISO 11299-2:2018(E)
©
ISO 2018
ISO 11299-2:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
ISO 11299-2:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms . 2
4.1 Symbols . 2
4.2 Abbreviated terms . 3
5 Pipes at the “M” stage . 3
5.1 Materials . 3
5.2 General characteristics . 3
5.3 Material characteristics . 3
5.4 Geometrical characteristics . 3
5.5 Mechanical characteristics. 3
5.6 Physical characteristics . 3
5.7 Jointing . 3
5.8 Marking . 3
5.9 Regional requirements for pipes . 3
6 Fittings at the “M” stage . 4
6.1 Requirement for fittings. 4
6.2 Marking . 4
6.3 Regional requirements for fittings . 4
7 Ancillary components . 4
8 Fitness for purpose of the installed lining system at the “I” stage .4
9 Installation practice . 4
9.1 Preparatory work . 4
9.2 Storage, handling and transport . 4
9.3 Equipment . 5
9.3.1 Butt fusion equipment and debeading equipment. 5
9.3.2 Pipe rollers . 5
9.3.3 Winching and rod-pulling equipment . 5
9.3.4 Pipe entry guides . 5
9.3.5 Electrofusion equipment . 5
9.3.6 Inspection equipment . 5
9.3.7 Lifting equipment . 6
9.4 Installation . 6
9.5 Process-related inspection and testing . 6
9.6 Lining termination . 6
9.7 Reconnections to the existing pipeline system . 6
9.8 Final inspection and testing . 7
9.9 Documentation . 7
Annex A (normative) Layered pipes . 8
Bibliography .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.