EN 420:2003+A1:2009
(Main)Protective gloves - General requirements and test methods
Protective gloves - General requirements and test methods
This standard defines the general requirements and relevant test procedures for glove design and construction, resistance of glove materials to water penetration, innocuousness, comfort and efficiency, marking and information supplied by the manufacturer applicable to all protective gloves.
NOTE It can also be applicable to arm protectors and gloves permanently incorporated in containment enclosures.
This European Standard does not address the protective properties of gloves and therefore should not be used alone but only in combination with the appropriate specific European Standard(s).
A non exhaustive list of these standards is given in the Bibliography.
Schutzhandschuhe - Allgemeine Anforderungen und Prüfverfahren
Diese Norm legt die für alle Schutzhandschuhe anzuwendenden relevanten Prüfverfahren und die allgemeinen Anforderungen zu Gestaltungsgrundsätzen, Handschuhkonfektionierung, Widerstand des Handschuhmaterials gegen Wasserdurchdringung, Unschädlichkeit, Komfort und Leistungsvermögen sowie die vom Hersteller vorzunehmende Kennzeichnung und vom Hersteller zu liefernden Informationen fest.
ANMERKUNG Sie kann auch auf Armschutz und auf Handschuhe angewendet werden, die ständig in geschlossenen Behältnissen eingesetzt werden.
Diese Europäische Norm befasst sich nicht mit den schützenden Eigenschaften von Handschuhen und ist daher nie alleine, sondern nur in Kombination mit den zutreffenden spezifischen Europäischen Normen anzuwenden.
Eine nicht abschließende Liste dieser Normen enthalten die Literaturhinweise dieser Norm.
Gants de protection - Exigences générales et méthodes d'essai
La présente Norme européenne définit les exigences générales et les procédures d’essai concernant l’ergonomie
et la construction du gant, la résistance des matériaux constitutifs à la pénétration de l’eau, l’innocuité, le confort
et l’efficacité, le marquage et l’information fournie par le fabricant applicables à tous les gants de protection.
NOTE Elle peut aussi s’appliquer aux protecteurs du bras et aux gants incorporés de manière permanente à des enceintes
fermées.
Cette présente Norme européenne ne concerne pas les propriétés de protection des gants et ne doit donc pas être
utilisée seule mais seulement en association avec le(s) Norme(s) européenne(s) spécifique(s) appropriée(s).
Une liste non exhaustive de ces normes est donnée dans la bibliographie.
Varovalne rokavice - Splošne zahteve in preskusne metode
Ta standard opredeljuje splošne zahteve in ustrezne preskusne postopke za oblikovanje rokavic in njihovo izdelavo, odpornost materialov za rokavice proti prodiranju vode, neškodljivost, udobje, učinkovitost, označevanje in informacije, ki jih zagotovi proizvajalec in ki veljajo za vse varovalne rokavice. Ta evropski standard ne naslavlja varovalnih lastnosti rokavic in se ga potemtakem ne sme uporabljati samega, ampak le v povezavi s primernimi posebnimi evropskimi standardi. Neizčrpen seznam teh standardov je podan v bibliografiji.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Varovalne rokavice - Splošne zahteve in preskusne metodeSchutzhandschuhe - Allgemeine Anforderungen und PrüfverfahrenGants de protection - Exigences générales et méthodes d'essaiProtective gloves - General requirements and test methods13.340.40Varovanje dlani in rokHand and arm protectionICS:Ta slovenski standard je istoveten z:EN 420:2003+A1:2009SIST EN 420:2003+A1:2010en,fr,de01-januar-2010SIST EN 420:2003+A1:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 420:2003+A1
November 2009 ICS 13.340.40 Supersedes EN 420:2003English Version
Protective gloves - General requirements and test methods
Gants de protection - Exigences générales et méthodes d'essai
Schutzhandschuhe - Allgemeine Anforderungen und Prüfverfahren This European Standard was approved by CEN on 24 July 2003
and includes Corrigendum 1 issued by CEN on 29 November 2006 and Amendment 1 approved by CEN on 10 October 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 420:2003+A1:2009: ESIST EN 420:2003+A1:2010
Definition of "For minimal risks only" . 21Annex B (normative)
Pictograms . 23Annex C (informative)
Test results — Uncertainty of measurement . 24Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or other provisions of EU Directives . 25Bibliography . 26 SIST EN 420:2003+A1:2010
Key a
Hand b
Back c
Palm Figure 1 — Definitions of hand, palm and back 3.1 hand part of the body from the tip of the middle finger to the wrist 3.2 glove personal protective equipment (PPE) which protects the hand or part of the hand against hazards. It can additionally cover part of the forearm and arm 3.3 glove palm part of the glove which covers the palm of the hand, i.e. from the wrist to the base of the fingers 3.4 glove back part of the glove which covers the back of the hand (i.e. from the wrist to the base of the fingers) 3.5 dexterity manipulative ability to perform a task 3.6 hazard situation which can be the cause of any harm or damage to the health of the human body. A non exhaustive list of specific standards dealing with hazards is given in the Bibliography SIST EN 420:2003+A1:2010
EN 344-1:1992 Level of performance Time of penetration min 1 2 3 4 30
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.