EN 12629-5-1:2003

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-1: Pipe making machines manufacturing in the vertical axis

This European Standard applies to machines for vertical manufacture of pipes, manholes and similar elements from concrete.
This European Standard deals with the significant hazards listed in clause 4, when used as intended under the conditions foreseen by the manufacturer. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, except noise hazards.
NOTE   Amendment is under preparation to deal with noise, in particular for measures to reduce noise at source and a noise test code including noise declaration.
This standard establishes safety requirements and/or methods of protection which applies to these machines.
This European standard applies to the pipe making machines manufacturing in the vertical axis which may form an integral part of a pipe making process plant.
See 1.4 of EN 12629-1:2000.

Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 5-1: Beton-Rohrmaschinen mit Fertigung in vertikaler Lage

1.1   Diese Europäische Norm gilt für Maschinen zur Herstellung von Rohren, Schächten und ähnlichen Beton-elementen in vertikaler Lage.
1.2   Diese Europäische Norm behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefähr-dungsereignisse (siehe Abschnitt 4), die auf diese Maschinen zutreffen, wenn sie bestimmungsgemäß und ent-sprechend den vorhersehbaren Bedingungen des Herstellers verwendet werden. Diese Europäische Norm spezifi-ziert die entsprechenden technischen Maßnahmen zur Beseitigung oder Verminderung der Risiken, die von diesen Gefährdungen ausgehen, außer Gefährdungen durch Lärm.
ANMERKUNG   Eine Änderung ist in Vorbereitung, die Lärm behandelt sowie insbesondere Maßnahmen zur Lärmminderung an der Quelle und ein Geräuschmessverfahren einschließlich der Angabe von Geräuschemissionswerten.
Diese Norm behandelt Sicherheitsanforderungen und/oder Schutzmaßnahmen, die für diese Maschinen gelten.
1.3   Diese Europäische Norm gilt für Beton-Rohrmaschinen mit Fertigung in vertikaler Lage, die als integraler Bestandteil einer Rohrherstellungsanlage dienen können.
1.4   Siehe 1.4 von EN 12629-1:2000.

Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 5-1: Machines pour la fabrication de tuyaux dans l'axe vertical

1.1   La présente Norme européenne s'applique aux machines utilisées pour la fabrication verticale de tuyaux, trous d'homme et produits similaires en béton.
1.2   La présente Norme européenne traite les phénomènes dangereux significatifs relatifs à ces machines listés dans l'Article 4, lorsqu'elles sont utilisées normalement et dans les conditions prévues par le constructeur. Cette Norme européenne spécifie les mesures techniques appropriées permettant d'éliminer ou de réduire les risques dus aux phénomènes dangereux significatifs, à l'exception du bruit.
NOTE   Un amendement est en préparation pour traiter du bruit, en particulier les moyens de réduction du bruit à  la source et un code d'essai de bruit qui comprend la déclaration de bruit.
La présente norme spécifie les prescriptions de sécurité et/ou méthodes de protection qui s'appliquent à ces machines.
1.3   La présente Norme européenne s'applique aux machines de fabrication des tuyaux travaillant sur l'axe vertical qui peuvent former partie intégrante d'une installation de fabrication de tuyaux.
1.4   Voir 1.4 de l'EN 12629-1:2000.

Stroji za izdelavo gradbenih proizvodov iz betona in apnenega peščenca - Varnost - 5-1. del: Stroji za izdelavo cevi po navpični osi

General Information

• Status: Withdrawn
• Publication Date: 16-Dec-2003
• Withdrawal Date: 31-Aug-2010
• ICS: 91.220 - Construction equipment
• Technical Committee: CEN/TC 151 - Construction equipment and building material machines - Safety
• Drafting Committee: CEN/TC 151/WG 10 - Machines and plant for the production of stones, slabs, pipes, prefabricated elements of concrete and calcium-silicate - Safety
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 01-Sep-2010
• Completion Date: 01-Sep-2010
• Directive: 98/37/EC - Machinery
• Mandate: M/BC/CEN/88/13 - Standardization request to CEN/CENELEC relating to machinery
• Ref Project: SIST EN 12629-5-1:2004 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-1: Pipe making machines manufacturing in the vertical axis

Relations

• Merged Into: EN 12629-5-1:2003+A1:2010 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-1: Pipe making machines manufacturing in the vertical axis
• Effective Date: 10-Jul-2010
• Amended By: EN 12629-5-1:2003/FprA1 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-1: Pipe making machines manufacturing in the vertical axis
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 5-1: Beton-Rohrmaschinen mit Fertigung in vertikaler LageMachines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 5-1: Machines pour la fabrication de tuyaux dans l'axe verticalMachines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-1: Pipe making machines manufacturing in the vertical axis91.220Gradbena opremaConstruction equipmentICS:Ta slovenski standard je istoveten z:EN 12629-5-1:2003SIST EN 12629-5-1:2004en01-september-2004SIST EN 12629-5-1:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12629-5-1December 2003ICS 91.220English versionMachines for the manufacture of constructional products fromconcrete and calcium-silicate - Safety - Part 5-1: Pipe makingmachines manufacturing in the vertical axisMachines pour la fabrication de produits de construction enbéton et silico-calcaire - Sécurité - Partie 5-1: Machinespour la fabrication de tuyaux dans l'axe verticalMaschinen für die Herstellung von Bauprodukten aus Betonund Kalksandsteinmassen - Sicherheit - Teil 5-1: Beton-Rohrmaschinen mit Fertigung in vertikaler LageThis European Standard was approved by CEN on 3 November 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12629-5-1:2003: ESIST EN 12629-5-1:2004

Definitions of terms.17Annex B (informative)
Hazard zones.21Annex ZA (informative)
Relationship of this document with EC Directives.25Bibliography.26SIST EN 12629-5-1:2004

–
for pipes and similar elements (SeeFigure A.1)Type 2Semi-automatic type of machine (works with crane for demoulding) that can have more casting stations –for pipes, manholes and similar elements (See Figure A.2)Type 3Fully automatic machine type with auxiliary automation equipment – mainly for manholes (See FigureA.3)Type 4Fully automatic machine type with auxiliary automation equipment (works with crane or forklift truck fordemoulding) – for pipes (See Figure A.4)3.3mixture feed equipmentequipment which is integral with the pipe making machine for the receiving and transfer of the mixture to thecasting station3.4casting mouldcomponent consisting of a pallet or base ring, inner former and an outer shell, the concrete pipe is formed in thespace between the inner former and the shell3.5packerheadrotating device which passes through the mould to distribute and compact the concrete within the casting mould3.6casting stationpart of the pipe-making machine which consists of the casting mould(s) and associated fixtures where the pipes areformed3.7machine pitpart of the machine which is below floor level and can contain part of the casting station3.8automatic pallet feeding unitdevice which is an integral part of the machine, which automatically supplies pallets or base rings to the castingmould or casting station3.9automatic reinforcing material feederDevice which is an integral part of the machine, which automatically supplies reinforcing elements to the castingstation.3.10automatic pipe accessory feederDevice which is an integral part of the machine, which automatically supplies pipe accessories which are notconcrete (i.e. step-irons, lifting anchors) to positions within the casting station.SIST EN 12629-5-1:2004

(see informative annex B)Mechanical hazardsas per annex A of EN 1050:1996List of hazards and hazardous situationsFigure B.1(Type 1)Figure B.2(Type 2)Figure B.3(Type 3)Figure B.4(Type 4)- Between fixed and moving parts in the mixture feedmechanism area1111- Between fixed and moving parts within the casting area232, 54- Between fixed and moving parts within the machine pit3232- Between fixed and moving parts in the automatic palletfeed area4-4, 5-- Between fixed and moving parts in the area ofautomated equipment for feeding reinforcing elementsand pipe accessories i.e. step irons5-2, 4, 5-- Struck by falling pipe/mould during removal fromcasting area6-63, 4- Between fixed and moving parts in the pipe off-bearerarea6-6-1.1 Crushing hazards- Between fixed and moving parts in the rotating platformarea---2, 3, 4- Between fixed and moving parts in the mixture feedmechanism area1111- Between fixed and moving parts within the casting area232, 541.2
Shearing hazard- Between fixed and moving parts within the machine pit3232SIST EN 12629-5-1:2004

(see informative annex B)Mechanical hazardsas per annex A of EN 1050:1996List of hazards and hazardous situationsFigure B.1(Type 1)Figure B.2(Type 2)Figure B.3(Type 3)Figure B.4(Type 4)- Between fixed and moving parts in the automatic palletfeed area4-4, 5-- Between fixed and moving parts in the area ofautomated equipment for feeding reinforcing elementsand pipe accessories i.e. step irons5-2, 4, 5-- Between fixed and moving parts in the pipe off-bearerarea6---List of hazards and hazardous situation
...