EN 848-3:2007+A2:2009

Safety of woodworking machines - One side moulding machines with rotating tools - Part 3: Numerically controlled (NC) boring and routing machines

This document specifies all significant hazards, hazardous situations and events as listed in Clause 4, which are relevant to NC boring machines, NC routing machines and NC combined boring/routing machines (as defined in 3.2.1) herein after referred to as "machines" designed to cut solid wood, chip board, fibreboard, plywood and also these materials where these are covered with plastic laminate or edgings when they are used as intended and under the conditions foreseen by the manufacturer.
This document also applies to machines fitted with:
a)   additional equipment for sawing, sanding and edge banding;
b)   fixed or movable workpiece support;
c)   mechanical, pneumatic, hydraulic or vacuum workpiece clamping;
d)   automatic tool change facilities.
This document does not deal with the specific hazards of edge banding equipment fitted to NC boring machines, NC routing machines and NC combined boring/routing machines.
This document is only applicable to NC boring machines, NC routing machines and NC combined boring/routing machines which are designed to use milling tools with a cutting circle diameter below 16 mm or milling tools or saw-blades conforming to EN 847-1:2005 and EN 847-2:2001 and boring tools or sanding wheels.
This document is not applicable to NC boring machines, NC routing machines and NC combined boring/routing machines which are designed to use grinding wheels.
This document is not applicable to single spindle hand fed/integrated fed routing machines.
NOTE   Single spindle hand fed/integrated fed routing machines are dealt with in EN 848-2:2007.
This document does not deal with the specific hazards of ejection through curtains on machines with feeding openings of which the distance between the workpiece support and the lower part of the partial enclosure in the direction of the feed exceeds 400 mm.
This document is not applicable to NC boring machines, NC routing machines and NC combined boring/routing machines which are manufactured before the d

Sicherheit von Holzbearbeitungsmaschinen - Fräsmaschinen für einseitige Bearbeitung mit drehendem Werkzeug - Teil 3: NC-Bohr- und Fräsmaschinen

Sécurité des machines pour le travail du bois - Machines à fraiser sur une face à outil rotatif - Partie 3 : Perceuses et défonceuses à commande numérique

Le présent document !spécifie" tous les phénomènes dangereux, situations et événements dangereux significatifs tels qu’énumérés à l’Article 4, applicables aux perceuses, aux défonceuses et aux perceuses/défonceuses à commande numérique (telles que définies en 3.2.1) désignées ci-après sous le terme «machines», celles-ci sont conçues pour usiner du bois, des panneaux de fibres ou de particules, de contreplaqué ainsi que ces matériaux lorsque leurs surfaces ou leurs chants sont recouverts de plastique ou de plaquage, durant l’utilisation normale et dans les conditions prévues par le fabricant.
Le présent document est applicable aux machines équipées :
a)   d’unités supplémentaires de sciage, de ponçage, de plaquage sur chant ;
b)   de support de pièce fixe ou mobile ;
c)   de serrage de pièce mécanique, hydraulique, pneumatique ou par dépression ;
d)   de dispositifs de changement automatique d’outils.
Le présent document ne traite pas des phénomènes dangereux spécifiques aux unités de plaquage sur chant montées sur les perceuses, les défonceuses et les perceuses/défonceuses à commande numérique.
Le présent document ne s'applique qu’aux perceuses, défonceuses et perceuses/défonceuses à commande numérique conçues pour utiliser des fraises ayant un diamètre de coupe en dessous de 16 mm, ou des fraises ou des lames conformes à l'EN 847-1:2005 et à l’EN 847-2:2001, et des forets ainsi que des roues de ponçage.
Le présent document ne s'applique pas aux perceuses, défonceuses et perceuses/défonceuses à commande numérique conçues pour utiliser des meules.
Le présent document ne s'applique pas aux défonceuses monobroches à avance manuelle ou mécanisée.
NOTE   Les défonceuses monobroches à avance manuelle ou mécanisée sont traitées dans l’EN 848-2:2007.
(...)

Varnost lesnoobdelovalnih strojev - Rezkalniki z vrtilnim orodjem za enostransko obdelavo - 3. del: Numerično krmiljeni (NC) vrtalni in rezkalni stroji

General Information

• Status: Withdrawn
• Publication Date: 29-Sep-2009
• Withdrawal Date: 23-Oct-2012
• ICS: 79.120.10 - Woodworking machines
• Technical Committee: CEN/TC 142 - Woodworking machines - Safety
• Drafting Committee: CEN/TC 142/WG 5 - Spindle moulding, routing machines and machine centres
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 24-Oct-2012
• Completion Date: 24-Oct-2012
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Mandate: M/311 - Standardization mandate awarded to the CEN within the framework of Directive 98/37/EC relating to machinery, with a view to revision of EN standard 848-3:1999 concerning the safety of woodworking machines
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN 848-3:2007+A2:2009 - Safety of woodworking machines - One side moulding machines with rotating tools - Part 3: Numerically controlled (NC) boring and routing machines

Relations

• Merged From: EN 848-3:2007 - Safety of woodworking machines - One side moulding machines with rotating tools - Part 3: Numerically controlled (NC) boring and routing machines
• Effective Date: 19-Jan-2023
• Merged From: EN 848-3:2007/prA1 - Safety of woodworking machines - One side moulding machines with rotating tools - Part 3: Numerically controlled (NC) boring and routing machines
• Effective Date: 18-Jan-2023
• Replaced By: EN 848-3:2012 - Safety of woodworking machines - One side moulding machines with rotating tool - Part 3: Numerically controlled (NC) boring and routing machines
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY5H]NDOQLNL]YUWLOQLPRURGMHP]DHQRVWUDQVNR
REGHODYRGHO1XPHULþQRNUPLOMHQL1&YUWDOQLLQUH]NDOQLVWURML
Safety of woodworking machines - One side moulding machines with rotating tools - Part
3: Numerically controlled (NC) boring and routing machines
Sicherheit von Holzbearbeitungsmaschinen - Fräsmaschinen für einseitige Bearbeitung
mit drehendem Werkzeug - Teil 3: NC-Bohr- und Fräsmaschinen
Sécurité des machines pour le travail du bois - Machines à fraiser sur une face à outil
rotatif - Partie 3: Perceuses et défonceuses à commande numérique
Ta slovenski standard je istoveten z: EN 848-3:2007+A2:2009
ICS:
25.040.20 âWHYLOþQRNUPLOMHQLVWURML Numerically controlled
machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 848-3:2007+A2
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2009
ICS 79.120.10 Supersedes EN 848-3:2007
English Version
Safety of woodworking machines - One side moulding machines
with rotating tools - Part 3: Numerically controlled (NC) boring
and routing machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
fraiser sur une face à outil rotatif - Partie 3: Perceuses et Fräsmaschinen für einseitige Bearbeitung mit drehendem
défonceuses à commande numérique Werkzeug - Teil 3: NC-Bohr- und Fräsmaschinen
This European Standard was approved by CEN on 17 February 2007 and includes Amendment 1 approved by CEN on 30 July 2009 and
Amendment 2 approved by CEN on 24 August 2009.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 848-3:2007+A2:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .9
3.1 General .9
3.2 Definitions .9
4 List of significant hazards . 17
5 Safety requirements and/or measures . 20
5.1 General . 20
5.2 Controls . 21
5.2.1 Safety and reliability of control systems . 21
5.2.2 Position of controls . 22
5.2.3 Starting . 23
5.2.4 Normal stopping . 23
5.2.5 Emergency stop . 24
5.2.6 Operational stop . 25
5.2.7 Mode selection switch . 25
5.2.8 Speed monitoring and control . 27
5.2.9 Interlocking of guards, protective devices, movements and functions. 29
5.2.10 Failure of the power supply . 29
5.2.11 Failure of the control circuits . 30
5.3 Protection against mechanical hazards . 30
5.3.1 Stability . 30
5.3.2 Risk of break-up during operation . 30
5.3.3 Tool holder . 30
5.3.4 Braking tool spindle . 31
5.3.5 Devices to minimise the risk of ejection . 32
5.3.6 Workpiece supports and guides . 32
5.3.7 Prevention of access to moving parts and devices to minimise the effect of ejection . 32
5.3.8 Clamping device . 43
5.4 Protection against non mechanical hazards . 45
5.4.1 Fire . 45
5.4.2 Noise . 45
5.4.3 Emission of chips and dust . 46
5.4.4 Electricity . 46
5.4.5 Ergonomics and handling . 47
5.4.6 Lighting . 47
5.4.7 Pneumatics . 47
5.4.8 Hydraulics . 47
5.4.9 Static electricity . 48
5.4.10 Electromagnetic compatibility . 48
5.4.11 Lasers . 48
5.4.12 Unintended movements . 48
5.4.13 Supply disconnecting devices . 48
5.4.14 Maintenance . 49
6 Information for use . 49
6.1 Warning devices . 49
6.2 Marking . 49
6.3 Instruction handbook . 50
Annex A (informative) Use of well tried components . 55
Annex B (normative) Operating conditions for noise measurement. 56
B.1 General . 56
B.2 Operating conditions for routing units of NC routing machines and NC combined
boring/routing machines . 56
B.2.1 General . 56
B.2.2 Noise measurements . 57
B.2.3 General data sheet . 59
B.3 Operating conditions for boring units of NC boring machines and NC combined
boring/routing machines . 61
B.3.1 General . 61
B.3.2 Noise measurements . 62
B.3.3 General data sheet . 64
Annex C (normative) Curtains on NC routing and NC combined boring and routing machines –
Impact test method . 67
C.1 General . 67
C.2 Test method . 67
C.2.1 Preliminary remarks . 67
C.2.2 Testing equipment . 67
C.2.3 Test procedure . 68
C.3 Results . 71
C.4 Assessment . 71
C.5 Test report . 71
Annex D (informative) #Example of a test equipment for impact test$ . 72
Annex E (normative) Braking tests . 73
E.1 Conditions for brake tests . 73
E.2 Tests .
...