EN ISO 8733:1997
(Main)Parallel pins with internal thread, of unhardened steel or austenitic stainless steel (ISO 8733:1997)
Parallel pins with internal thread, of unhardened steel or austenitic stainless steel (ISO 8733:1997)
Zylinderstifte mit Innengewinde aus ungehärtetem Stahl und austenitischem nichtrostendem Stahl (ISO 8733:1997)
Diese Internationale Norm beschreibt die Eigenschaften von Zylinderstiften mit Innengewinde aus ungehärtetem Stahl und austenitischem nichtrostendem Stahl mit metrischen Abmessungen und Nenndurchmessern d1 von 6 bis einschließlich 50 mm.
Goupilles cylindriques à trou taraudé en acier non trempé et en acier inoxydable austénitique (ISO 8733:1997)
La présente Norme internationale prescrit les caractéristiques des goupilles cylindriques à trou taraudé en acier non trempé et en acier inoxydable austénitique de diamètre nominal, d1, de 6 mm à 50 mm inclus.
Valjasti zatiči z notranjim navojem iz nekaljenega ali iz avstenitnega nerjavnega jekla (ISO 8733:1997)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8733:2001
01-julij-2001
1DGRPHãþD
SIST EN 28733:1996
9DOMDVWL]DWLþL]QRWUDQMLPQDYRMHPL]QHNDOMHQHJDDOLL]DYVWHQLWQHJDQHUMDYQHJD
MHNOD ,62
Parallel pins with internal thread, of unhardened steel or austenitic stainless steel (ISO
8733:1997)
Zylinderstifte mit Innengewinde aus ungehärtetem Stahl und austenitischem
nichtrostendem Stahl (ISO 8733:1997)
Goupilles cylindriques a trou taraudé en acier non trempé et en acier inoxydable
austénitique (ISO 8733:1997)
Ta slovenski standard je istoveten z: EN ISO 8733:1997
ICS:
21.060.50 =DWLþLåHEOML Pins, nails
SIST EN ISO 8733:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8733:2001
---------------------- Page: 2 ----------------------
SIST EN ISO 8733:2001
---------------------- Page: 3 ----------------------
SIST EN ISO 8733:2001
---------------------- Page: 4 ----------------------
SIST EN ISO 8733:2001
---------------------- Page: 5 ----------------------
SIST EN ISO 8733:2001
---------------------- Page: 6 ----------------------
SIST EN ISO 8733:2001
INTERNATIONAL ISO
STANDARD 8733
Second edition
1997-11-15
Parallel pins with internal thread,
of unhardened steel and austenitic
stainless steel
Goupilles cylindriques à trou taraudé en acier non trempé et
en acier inoxydable austénitique
A
Reference number
ISO 8733:1997(E)
---------------------- Page: 7 ----------------------
SIST EN ISO 8733:2001
ISO 8733:1997(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 8733 was prepared by Technical Committee
ISO/TC 2, Fasteners.
This second edition cancels and replaces the first edition (ISO 8733:1986),
which has been technically revised.
© ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet central@iso.ch
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii
---------------------- Page: 8 ----------------------
SIST EN ISO 8733:2001
©
INTERNATIONAL STANDARD ISO ISO 8733:1997(E)
Parallel pins with internal thread of unhardened steel
and austenitic stainless steel
1 Scope
This International Standard specifies the characteristics of parallel pins with internal thread of unhardened
steel and austenitic stainless steel with nominal diameters d from 6 mm to 50 mm inclusive.
1
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject
to revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO
maintain registers of currently valid International Standards.
1)
ISO 965-2:– , ISO general purpose metric screw threads – Tolerances – Part 2: Limits of sizes for general
purpose bolt and nut thread – Medium quality.
ISO 3269:1988, Fasteners – Acceptance inspection.
ISO 3506-1:1997, Corrosion-resistant stainless steel fasteners – Part 1: Bolts, screws and studs.
2)
ISO 4042: – , Fasteners – Electroplated coatings.
ISO 9717:1990, Phosphate conversion coatings for metals – Method of specifying requirements.
3 Dimensions
See figure 1 and table 1.
1) Slight flat or small groove at the manufacturer's discretion
Figure 1
1) To be published. (Revision of ISO 965-2:1980)
2) To be published. (Revision of ISO 4042:1989)
1
---------------------- Page: 9 ----------------------
SIST EN ISO 8733:2001
©
ISO
ISO 8733:1997(E)
Table 1 — Dimensions
Dimensions in millimetres
1)
m6
d 6 8 10 12 16 20 25 30 40 50
1
c ≈ 0,81 1,2 1,6 2 2,5345 6,3
1
c ≈ 1,2 1,6 2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.