EN 13675:2004/FprA1
(Amendment)Safety of machinery - Safety requirements for tube forming and rolling mills and finishing line equipment
Safety of machinery - Safety requirements for tube forming and rolling mills and finishing line equipment
2009-04-17 - CEN/TC 322 resubmit new version of text to CMC.
Sicherheit von Maschinen - Sicherheitsanforderungen an Rohrform- und Rohrwalzwerke und Adjustageanlagen
Sécurité des machines - Prescriptions pour formeuses et laminoirs à tubes et de lignes de parachèvement
Varnost strojev - Varnostne zahteve za cevarne, valjarne in opremo za pakiranje blaga
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2009
Varnost strojev - Varnostne zahteve za cevarne, valjarne in opremo za pakiranje
blaga
Safety of machinery - Safety requirements for tube forming and rolling mills and finishing
line equipment
Sicherheit von Maschinen - Sicherheitsanforderungen an Rohrform- und Rohrwalzwerke
und Adjustageanlagen
Sécurité des machines - Prescriptions pour formeuses et laminoirs à tubes et de lignes
de parachèvement
Ta slovenski standard je istoveten z: EN 13675:2004/FprA1
ICS:
13.110 Varnost strojev Safety of machinery
77.180 Oprema za metalurško Equipment for the
industrijo metallurgical industry
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
FINAL DRAFT
EN 13675:2004
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2009
ICS 77.180
English Version
Safety of machinery - Safety requirements for tube forming and
rolling mills and finishing line equipment
Sécurité des machines - Prescriptions pour formeuses et Sicherheit von Maschinen - Sicherheitsanforderungen an
laminoirs à tubes et de lignes de parachèvement Rohrform- und Rohrwalzwerke und Adjustageanlagen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 322.
This draft amendment A1, if approved, will modify the European Standard EN 13675:2004. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13675:2004/FprA1:2009: E
worldwide for CEN national Members.
Contents Page
Foreword .3
1 Modification to the "Foreword" .4
2 Modification to the Clause "1 Scope" .4
3 Modification to the "Introduction" .4
4 Modification to Clause "2 Normative references" .4
5 Modification to Clause "3 Terms and definitions" .7
6 Modification to Clause "4 List of significant hazards" .7
7 Modification to Clause "5 Safety Requirements and/or measures" and 5.1 .7
8 Modification to "5.2 List of hazards, hazardous situations, safety requirements and/or
measures (Table 1)" . 13
9 Modification to Table 1 . 14
10 Modification to "5.3.4 Hydraulic and pneumatic system" . 15
11 Modification to 5.4.1 " Noise reduction at source by design" . 15
12 Modification to "7.1 General", "7.2 Signals, warnings" and "7.3 Minimum marking" . 15
13 Modification to "7.4 Instruction handbook" . 16
14 Modification to Annex A . 19
15 Modification to Annex B . 23
16 Modification to Annex D . 28
17 Addition of new Annex ZB . 28
18 Modification to Bibliography . 28
Foreword
This document (EN 13675:2004/FprA1:2009) has been prepared by Technical Committee CEN/TC 322
“Equipment for making and shaping of metals — Safety requirements”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA and ZB, which is an integral part of this
document.
The new safety requirements as stated in this document comply with the additional relevant Essential
Requirements of the new Machinery Directive 2006/42/EC complementing the existing Machinery Directive
98/37/EC.
1 Modification to the "Foreword"
th
Replace the 4 paragraph with:
"For relationship with EU Directives, see informative Annexes ZA and ZB, which are integral parts of this
document.".
2 Modification to the Clause "1 Scope"
th
In the 4 paragraph, replace "prEN 12464-1" with "EN 12464-1".
3 Modification to the "Introduction"
Replace existing text with:
"This document is a type-C standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are
covered are indicated in the Scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or B
standards, the requirements of this type-C standard take precedence over the requirements of the other
standards for machines that have been designed and built according to the requirements of this type-C
standard.
Where for clarity an example of a preventative measure is given in the text, this should not be considered
as the only possible solution. Any other solution leading to the same risk reduction is permissible if an
equivalent level of safety is achieved.
This European Standard assumes that the equipment is operated and maintained by trained personnel.".
4 Modification to Clause "2 Normative references"
st
Replace the 1 paragraph with:
"The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies."
Due to comprehensive changes (e.g. EN with EN ISO) and new/updated standards, replace the whole list of
normative references with:
"EN 349:1993, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body
EN 614-1:2006, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general
principles
EN 614-2, Safety of machinery — Ergonomic design principles — Part 2: Interactions between the
design of machinery and work tasks
EN 626-1:1994, Safety of machinery — Reduction of risks to health from hazardous substances emitted
by machinery — Part 1: Principles and specifications for machinery manufacturers
EN 842, Safety of machinery — Visual danger signals — General requirements, design and testing
EN 853, Rubber hoses and hose assemblies — Wire braid reinforced hydraulic type — Specification
EN 854, Rubber hoses and hose assemblies — Textile reinforced hydraulic type — Specification
EN 856, Rubber hoses and hose assemblies — Rubber-covered spiral wire reinforced hydraulic type —
Specification
EN 857, Rubber hoses and hose assemblies — Wire braid reinforced compact type for hydraulic
applications — Specification
EN 894-1, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 1: General principles for human interactions with displays and control actuators
EN 894-2, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 2: Displays
EN 894-3, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 3: Control actuators
EN 953:1997, Safety of machinery — Guards — General requirements for the design and construction
of fixed and movable guards
EN 981:1996, Safety of machinery — System of auditory and visual danger and information signals
EN 982:1996, Safety of machinery — Safety requirements for fluid power systems and their components
— Hydraulics
EN 983:1996, Safety of machinery — Safety requirements for fluid power systems and their components
— Pneumatics
EN 999:1998, Safety of machinery — The positioning of protective equipment in respect of approach
speeds of parts of the human body
EN 1037:1995, Safety of machinery — Prevention of unexpected start-up
EN 1063, Glass in building — Security glazing — Testing and classification of resistance against bullet
attack
EN 1088:1995, Safety of machinery — Interlocking devices associated with guards — Principles for
design and selection
EN 1299, Mechanical vibration and shock — Vibration isolation of machines — Information for the
application of source isolation
EN 1837, Safety of machinery — Integral lighting of machines
EN 12198-1, Safety of machinery — Assessment and reduction of risks arising from radiation emitted by
machinery — Part 1: General principles
EN 12254, Screens for laser working places — Safety requirements and testing
EN 13861, Safety of machinery — Guidance for the application of ergonomics standards in the design of
machinery
EN 14253, Mechanical vibration — Measurement and calculation of occupational exposure to whole-
body vibration with reference to health — Practical guidance
EN 50171, Central power supply systems
EN 60204-1:2006, Safety of machinery — Electrical equipment of machines — Part 1: General
requirements (IEC 60204-1:2005, modified)
EN 60447, Basic and safety principles for man-machine interface — Marking and identification —
Actuating principles (IEC 60447:2004)
EN 60825-1:2007, Safety of laser products — Part 1: Equipment classification and requirements
(IEC 60825-1:2007)
EN 61310-1, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for visual,
acoustic and tactile signals (IEC 61310-1:2007)
EN 61310-2, Safety of machinery — Indication, marking and actuation — Part 2: Requirements for
marking (IEC 61310-2:2007)
EN 61496-1, Safety of machinery — Electro- sensitive protective equipment — Part 1: General
requirements and tests (IEC 61496-1:2004, modified)
EN 60529:1991, Degrees of protection provided by enclosures (IP code) (IEC 60529:1989)
EN ISO 4871:1996, Acoustics — Declaration and verification of noise emission values of machinery and
equipment (ISO 4871:1996)
EN ISO 7731:2005, Ergonomics — Danger signals for public and work areas — Auditory danger signals
(ISO 7731:2003)
EN ISO 9692-2, Welding and allied processes — Joint preparation — Part 2: Submerged arc welding of
steels (ISO 9692-2:1998)
EN ISO 11064-1, Ergonomic design of control centres — Part 1: Principles for the design of control
centres (ISO 11064-1:2000)
EN ISO 11202, Acoustics — Noise emitted by machinery and equipment — Measurement of emission
sound pressure levels at a work station and at other specified positions — Survey method in situ
(ISO 11202:1995)
EN ISO 11688-1, Acoustics — Recommended practice for the design of low-noise machinery and
equipment — Part 1: Planning (ISO/TR 11688-1:1995)
EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1:
Basic terminology, methodology (ISO 12100-1:2003)
EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2:
Technical principles (ISO 12100-2:2003)
EN ISO 13732-1:2008, Ergonomics of the thermal environment — Methods for the assessment of
human responses to contact with surfaces — Part 1: Hot surfaces (ISO 13732-1:2006)
EN ISO 13849-1:2006, Safety of machinery — Safety-related parts of control systems — Part 1: General
principles for design (ISO 13849-1:2006)
EN ISO 13850:2006, Safety of machinery — Emergency stop — Principles for design (ISO 13850:2006)
EN ISO 13857:2008, Safety of machinery — Safety distances to prevent hazard zones being reached by
upper and lower limbs (ISO 13857:2008)
EN ISO 14121-1, Safety of machinery — Risk assessment — Part 1: Principles (ISO 14121-1:2007)
EN ISO 14122-1, Safety of machinery — Permanent means of acce
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.