EN 14420-4:2022
(Main)Hose fittings with clamp units - Part 4: Flange connections
Hose fittings with clamp units - Part 4: Flange connections
This document specifies requirements for hose tails according to EN 14420-2, with flanges of mating dimensions PN 10/PN 16/PN 25/PN 40 (according to nominal size and pressure stage) according to EN 1092-1, on hose fittings with clamp units according to EN 14420-3.
Maximum working pressure is 25 bar; maximum working temperature is 65 °C.
Additionally, flanges are also usable according to EN 14422.
Schlaucharmaturen mit Klemmfassungen - Teil 4: Flanschanschlüsse
Dieses Dokument legt Anforderungen an Schlauchstutzen nach EN 14420-2 mit Flanschen mit Anschlussmaßen PN 10/PN 16/PN 25/PN 40 (je nach Nennweite und Druckstufe) nach EN 1092-1, für Schlaucharmaturen mit Klemmfassungen nach EN 14420-3 fest.
Der höchstzulässige Betriebsdruck beträgt 25 bar, die höchstzulässige Betriebstemperatur beträgt 65 °C.
Zusätzlich sind auch Flansche nach EN 14422 verwendbar.
Raccords pour flexibles avec demi-coquille - Partie 4 : Raccordements à bride
Le présent document spécifie les exigences applicables aux douilles à brides conformes à l’EN 14420-2 de
dimensions d'assemblage PN 10/PN 16/PN 25/PN 40 (selon la dimension nominale et l’étage de
pression) conformes à l'EN 1092-1, pour raccords de flexibles avec demi-coquille conformes à
l'EN 14420-3.
La pression de service maximale est de 25 bar1 ; la température de service maximale est de 65 °C.
En outre, les brides sont également utilisables conformément à l’EN 14422.
Cevni fitingi z objemkami - 4. del: Prirobnični spoji
Ta dokument določa zahteve za cevne nastavke v skladu s standardom EN 14420-2 s prirobnicami z dimenzijami spajanja PN 10/PN 16/PN 25/PN 40 (glede na nominalno velikost in stopnjo tlaka) v skladu s standardom EN 1092-1 na cevnih fitingih z objemkami v skladu s standardom EN 14420-3.
Največji delovni tlak je 25 barov; najvišja delovna temperatura je 65 °C.
Poleg tega se lahko prirobnice uporabljajo tudi v skladu s standardom EN 14422.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2022
Nadomešča:
SIST EN 14420-4:2013
Cevni fitingi z objemkami - 4. del: Prirobnični spoji
Hose fittings with clamp units - Part 4: Flange connections
Schlaucharmaturen mit Klemmfassungen - Teil 4: Flanschanschlüsse
Raccords pour flexibles avec demi-coquille - Partie 4 : Raccordements à bride
Ta slovenski standard je istoveten z: EN 14420-4:2022
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 14420-4
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2022
EUROPÄISCHE NORM
ICS 23.040.70 Supersedes EN 14420-4:2013
English Version
Hose fittings with clamp units - Part 4: Flange connections
Raccords pour flexibles avec demi-coquille - Partie 4 : Schlaucharmaturen mit Klemmfassungen - Teil 4:
Raccordements à bride Flanschanschlüsse
This European Standard was approved by CEN on 24 July 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14420-4:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 6
4 Hose fittings with flanges . 6
5 Dimensions, designations . 7
5.1 General . 7
5.2 Hose tail with weld neck collar and loose flange . 8
5.3 Hose tail with fixed flange . 8
5.4 Hose tail . 9
5.5 Weld joints . 10
6 Surface finish . 10
7 Materials . 11
7.1 Hose tail . 11
7.2 Weld neck collar and fixed flanges . 12
7.3 Loose flanges . 12
8 Marking . 13
9 Type testing and quality control . 13
Bibliography . 14
European foreword
This document (EN 14420-4:2022) has been prepared by Technical Committee CEN/TC 218 “Rubber
and plastics hoses and hose assemblies”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2023, and conflicting national standards
shall be withdrawn at the latest by February 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14420-4:2013.
In comparison to EN 14420-4:2013, the following changes have been made:
— In Clause 2, the normative references have been updated;
— In Figure 1 and Figure 2, the indication of the length L has been deleted;
— In Figure 3 and Figure 4, the indication of the length l and l has been deleted;
1 2
— In Clause 4, Table 2 has been deleted;
— In Clause 5, Table 3 and Table 4 have been deleted;
— In Clause 5, Table 5 has been renamed to Table 2 and for the nominal size DN 200, the value s has
been updated to 6,3 mm.
The EN 14420 series, Hose fittings with clamp units, consists of the following parts:
— Part 1: Requirements, types of fixing and connection, designation and testing
— Part 2: Hose side parts of hose tail
— Part 3: Clamp units, bolted or pinned
— Part 4: Flange connections
— Part 5: Threaded connections
— Part 6: TW tank truck couplings
— Part 7: Cam locking couplings
— Part 8: Symmetrical half coupling (Guillemin system)
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the follow-
ing countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cy-
prus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
1 Scope
This document specifies requirements for hose tails according to EN 14420-2, with flanges of mating
dimensions PN 10/PN 16/PN 25/PN 40 (according to nominal size and pressure stage) according to
EN 1092-1, on hose fittings with clamp units according to EN 14420-3.
Maximum working pressure is 25 bar ; maximum working temperature is 65 °C.
Additionally, flanges are also usable according to EN 14422.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content con-
stitutes requirements of this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 573-3, Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part
3: Chemical composition and form of products
EN 1092-1, Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories,
PN designated - Part 1: Steel flanges
EN 1706, Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties
EN 10025-2, Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy
structural steels
EN 10088-1, Stainless steels - Part 1: List of stainless steels
EN 10216-1, Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy
steel tubes with specified room temperature properties
EN 10217-1, Welded steel tubes for pressure purposes - Technical delivery conditions - Part 1: Electric
welded and submerged arc welded non-alloy steel tubes with specified room temperature properties
EN 10283, Corrosion resistant steel castings
EN 10250-2, Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and
special steels
EN 12163, Copper and copper alloys - Rod for general purposes
EN 14420-1:2013, Hose fittings with clamp units - Part 1: Requirements, types of fixing and connection,
designation and testing
EN 14420-2, Hose fittings with clamp units - Part 2: Hose side parts of hose tail
EN 14420-3, Hose fittings with clamp units - Part 3: Clamp units, bolted or pinned
1 bar = 0,1 MPa.
EN 22768-1, General tolerances - Part 1: Tolerances for linear and angular dimensions without individual
tolerance indications (ISO 2768-1)
EN 22768-2 , General tolerances - Part 2: Geometrical tolerances for features without individual
tolerance indications (ISO 2768-2)
EN ISO 683-1, Heat-treatable steels, alloy steels and free-cutting steels - Part 1: Non-alloy steels for
quenching and tempering (ISO 683-1)
EN ISO 683-4, Heat-treatable steels, alloy steels and free-cutting steels - Part 4: Free-cutting steels
(ISO 683-4)
EN ISO 4042, Fasteners - Electroplated coating systems (ISO 4042)
EN ISO 8330, Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330)
EN ISO 11666, Non-destructive testing of welds - Ultrasonic testing - Acceptance levels (ISO 11666)
EN ISO 15614-1, Specification and qualification of welding procedures for metallic materials - Welding
procedure test - Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
(ISO 15614-1)
EN ISO 15614-2, Specification and qualification of welding procedures for metallic materials - Welding
procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2)
EN ISO 17636-1, Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray
techniques with film (ISO 17636-1)
EN ISO 17636-2, Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray
techniques with digital detectors (ISO 17636-2)
EN ISO 17638, Non-destructive testing of welds - Magnetic particle testing (ISO 17638)
EN ISO 17640, Non-destructive testing of welds - Ultrasonic testing - Techniques, testing levels, and
assessment (ISO 17640)
EN ISO 23277, Non-destructive testing of welds - Penetrant testing - Acceptance levels (ISO 23277)
EN ISO 23278, Non-destructive testing of welds - Magnetic particle testing - Acceptance levels (ISO 23278)
EN ISO 23279, Non-destructive testing of welds - Ultrasonic testing - Characterization of discontinuities in
welds (ISO 23279)
EN 22768-2 has been withdrawn and replaced by EN ISO 22081.
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 8330 and the following
apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
DN
nominal size
alphanumeric designation of size for components of a pipework system, which is used for reference
purposes; it comprises the letters DN followed by a dimensionless whole number which is indirectly
related to the physical size, in millimetres, of the bore or outside diameter of the end connections
Note 1 to entry: The number following the letters DN does not represent a measurable value and is not to be
used for calculation purposes except where specified in the relevant standard.
Note 2 to entry: In those standards which use the DN designation system, any relationship between DN and
component dimensions is to be indicated, e.g. DN/OD or DN/ID.
[SOURCE: EN ISO 6708:1995, 2.1, modified]
3.2
PN
alphanumeric designation used for reference purposes related to a combination of mechanical and
dimensional characteristics of a component of a hose fitting
Note 1 to entry: It comprises the letters PN followed by a dimensionless number.
Note 2 to entry: The number following the letters PN does not represent a measurable value and is not to be
used for calculation purposes except where specified in the relevant standard.
4 Hose fittings with flanges
Integral or welded flanges DN 15 to DN 200 according to EN 1092-1 shall be used (see Figure 1 and
Figure 2).
A parts list for hose fittings with flanges is given in Table 1.
Type FL Type FV
Figure 1 — Example of loose flange Figure 2 — Example of fix
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.