EN 14717:2005
(Main)Welding and allied processes - Environmental check list
Welding and allied processes - Environmental check list
This document provides check lists for the assessment of the environmental aspects of welding fabrication of metallic materials including site and repair work. Informative annexes indicate recommended actions for avoiding and reducing the possible environmental impacts outside the workshop.
Schweißen und verwandte Prozesse - Umweltcheckliste
Dieses Dokument legt Checklisten zum Bewerten von Umweltaspekten bei der Schweißfertigung von
metallischen Werkstoffen einschließlich Arbeiten auf Baustellen und Reparatur fest. Die informativen Anhänge
enthalten empfohlene Maßnahmen zum Vermeiden und Reduzieren von möglichen Umweltbelastungen
außerhalb der Werkstatt.
Soudage et techniques connexes - Liste de vérification relative à l'environnement
Le présent document fournit des listes de vérification pour l�évaluation des aspects environnementaux de la
fabrication par soudage faisant intervenir des matériaux métalliques, y compris les travaux sur site et la
réparation. Des Annexes informatives indiquent les actions recommandées permettant d�éviter ou de réduire
les possibles impacts sur l�environnement en dehors de l�atelier de fabrication.
Varjenje in sorodni postopki - Kontrolni vprašalnik v zvezi z okoljem
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2005
Varjenje in sorodni postopki - Kontrolni vprašalnik v zvezi z okoljem
Welding and allied processes - Environmental check list
Schweißen und verwandte Prozesse - Umweltcheckliste
Soudage et techniques connexes - Liste de vérification relative a l'environnement
Ta slovenski standard je istoveten z: EN 14717:2005
ICS:
13.020.01 Okolje in varstvo okolja na Environment and
splošno environmental protection in
general
25.160.01 Varjenje, trdo in mehko Welding, brazing and
spajkanje na splošno soldering in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 14717
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2005
ICS 13.020.01; 25.160.01
English version
Welding and allied processes - Environmental check list
Soudage et techniques connexes - Liste de vérification Schweißen und verwandte Prozesse - Umweltcheckliste
relative à l'environnement
This European Standard was approved by CEN on 15 March 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14717:2005: E
worldwide for CEN national Members.
Contents
Page
Foreword .3
Introduction.4
1 Scope .5
2 Normative references .5
3 Terms and definitions.5
4 Procedures .6
5 Check lists of possible environmental aspects.7
Annex A (informative) Assessment and recommended actions.10
Annex B (informative) Requirements.14
Bibliography.15
Foreword
This document (EN 14717:2005) has been prepared by Technical Committee CEN/TC 121 “Welding”, the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2005, and conflicting national standards shall be withdrawn at
the latest by October 2005.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
Introduction
Protection of the environment is a key political issue in Europe and elsewhere. Protection of the environment
is taken in a very broad sense. What is meant is the total life cycle aspects of, e.g. a product on the
environment, including expenditure of energy and during all phases from mining of raw materials, fabrication,
packaging, distribution, use, scrapping, recycling of materials, etc. However, assessment of all aspects of the
welded product or structure during its entire lifetime cycle is beyond the scope of the present document. The
document is limited to aspects directly related to welding fabrication.
The design of the fabricated structures puts a lower limit on the expenditure of energy during joint preparation
and welding, on the consumption of consumables and consequently on emissions of fumes and gases during
welding, etc. but the design phase is not covered by the document.
Welding fabrication has many environmental aspects. This document provides for a checklist, which may be
used for identification of environmental aspects during welding fabrication.
Provisions have to be restricted to a general guidance. Limit values are specified in national laws.
Some of the environmental aspects also have an implication for occupational health and safety, but the check
list in this document is incomplete for this use.
1 Scope
This document provides check lists for the assessment of the environmental aspects of welding fabrication of
metallic materials including site and repair work. Informative annexes indicate recommended actions for
avoiding and reducing the possible environmental impacts outside the workshop.
2 Normative references
Not applicable.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
welding fabrication
welding fabrication includes (for the purpose of this document) the following activities and associated
processes:
− joint preparation including thermal cutting and grinding;
− surface preparation including sand blasting, shot blasting, shot peening, chemical pickling and
cleaning;
− welding, including grinding and back gouging;
− soldering and brazing;
− thermal spraying;
− preheating and heat treatments;
− flame straightening and mechanical straightening;
− inspection and testing of welds and thermal sprayed surfaces.
3.2
disposal
collection, sorting, transport and treatment of waste as well as its storage and tipping above or under ground,
the transformation operations necessary for its re-use, recovery or recycling [Directive 75/442/EEC]
3.3
environment
surroundings in which an organization operates, including air, water, land, natural resources, flora, fauna,
humans and their interrelation [EN ISO 14001:2004]
3.4
environmental aspect
element of an organization's activities or products or services that can interact with the environment
[EN ISO 14001:2004]
3.5
environmental impact
any change to the environment, whether adverse or beneficial, wholly or partially resulting from an
organization's environmental aspects [EN ISO 14001:2004]
4 Procedures
Requirements for the protection of the environment during welding fabrication can originate from a number of
sources such as:
– legal requirements, often at the national level;
– commercial requirements (customer requirements);
– economical requirements, e.g. related to insurance.
Annex B provides further comments on the possible requirements.
Absolute limits, e.g. emissions, can apply but protection of the environment is, as a general rule, a continuous
process for which gradual improvements are aimed.
The check lists in the document can be used as a tool for determination of possible problem areas. In general
this applies to the following situations:
– when planning a fabrication, the application of new methods of fabrication or new equipment;
– for identification of procedures for monitoring or checks of actual environmental aspects;
– for specification of procedures for handling, storage and disposal of environmentally harmful substances.
All check lists state possible environmental aspects. Many aspects can be identified during the planning stage
as having no environmental impact. Others can be shown to be of no significance by monitoring or checking
the production processes. A few can result in further action to comply with the requirements. Annex A
provides some general guidance for assessment and possible actions.
5 Check lists of possible environmental aspects
Table 1 — Common to welding fabrication
Common to welding fabrication
Consumables Check for:
- Disposal of containers, packaging material, etc.;
- Disposal of used consumables and waste materials.
Equipment Check for:
- Energy and fuel efficiency;
- Generation of physical aspects, e.g. noise, heat and
radiation;
- Requirements for spare parts and consumables for
maintenance;
- Procedures for disposal of the equipment.
Work operation Check for:
- Disposal of scrap;
- Emission of fumes, gases and aerosols;
- Energy and fuel consumption;
- Fire hazards and explosion risks whenever there is a
risk of ignition;
- Generation of physical aspects, e.g. heat, light,
noise, radiation.
NOTE Several of the aspects listed above have a limited range of influence. It
depends on the circumstances whether they represent an environmental aspect or not.
Noise may e.g. not represent an environmental aspect when working in a large workshop
but may be a serious problem when working on site or performing repair work in
residential areas.
Table 2 — Joint and surface preparation, weld dressing, surface treatment and cleaning
Joint and surface preparation, weld dressing, surface treatment and
cleaning
Cleaning, pickling Check for:
and other chemical - Disposal of cleaning agents and other chemicals;
treatment
− Vapours;
− Leakage of consumables, cleaning agents, etc. from
storage vessels representing a risk of contamination
of soil, drains, watercourses or groundwater;
− Emission of hazardous substances in the air.
Grinding and Check for:
gouging − Disposal of dust, used grinding wheels and other
tools for grinding;
− Dust explosions;
a
−
Emission of dust;
− Noise.
Sandblasting, shot Check for:
blasting, shot
− Disposal of dust and used sand/shot;
a
peening, etc.
− Emission of dust;
− Noise.
Thermal cutting Check for:
− Disposal of scrap, slag or mud;
− Emission of UV-/IR-radiation;
a
− Emission of dust;
− Noise;
− Use of coolants;
− Emission of hazardous gases, e.g. nitrogen oxide (if
relevant).
a
Un-controlled emission of dust (not least when working on site) may represent a risk of
contamination of soil, drains, watercourses or groundwater, e.g. by heavy metals.
Table 3 — Welding, brazing and soldering
Welding, brazing and soldering
Welding, brazing Check for:
and soldering
− Disposal of non-permanent backing;
− Disposal of slag, fluxes and powders;
− Emission of UV-/IR-radiation;
−
a
Emission of fume, dust and gases;
− Noise;
− Use of coolants.
a
Un-controlled emission of dust (not least when working on site) may represent a risk of
contamination of soil, drains, watercourses or groundwater, e.g. by heavy metals.
Table 4 — Thermal spraying
Thermal spraying
Thermal spraying Check for:
− Emission of fume and dust;
− Disposal of dust;
− Noise;
− Pollution of water curtain;
− Radiation (arc processes).
Table 5 — Pre- and post heating and post weld heat treatment
Pre- and post heating and post weld heat treatment
Pre- and post heating and post Check for:
weld heat treatment
− Disposal of insulating materials and other materials (in
particular for temporary ovens);
− Use of coolants.
− Energy consumption (e.g. efficiency of insulation).
Table 6 — Inspection and testing
Inspection and testing
Inspection and testing Check for:
− Disposal of chemicals used for development of
radiographs;
− Disposal of radiographs after use;
− Ionising radiation;
− Use and disposal of fluids and powders used for
magnetic particle testing;
− Use and disposal of penetrant and cleaning materials;
− Cleaning/disposal of UT couplants.
Table 7 — Destructive testing
Destructive testing
Destructive testing Check for:
− Use and disposal of chemicals used for preparation of
test pieces;
− Disposal of scrap and test pieces after use;
− Environmental aspects related to sampling and
preparation of test pieces. Table 2 may be used as a
check list.
Annex A
(informative)
Assessment and recommended actions
The table below gives some indications of the assessment of the environmental aspects and some suggestions
for actions in case any adverse environmental impact has been identified.
Table A.1 — Assessment and recommended actions
Environmental Suggested assessment Recommended actions when adverse
aspect environmental impact has been identified
Chemicals Development of radiographs includes the use Used chemicals should be neutralised before
used for of potentially harmful chemicals. disposal or special arrangements for disposal
development of should be established. Used fixing baths hold
radiographs silver,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.