EN ISO 10442:2002
(Main)Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors (ISO 10442:2002)
Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors (ISO 10442:2002)
ISO 10442:2002 specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of constant-speed, packaged, integrally geared centrifugal air compressors, including their accessories, for use in the petroleum, chemical and gas service industries. It is also applicable to gas services other than air that are non-hazardous and non-toxic. It is not applicable to machines that develop a pressure rise of less than 35 kPa above atmospheric pressure, which are classed as fans or blowers.
Erdöl-, Chemie- und Erdgasindustrie - Turbo-Luftkompressoranlagen mit integriertem Getriebe (ISO 10442:2002)
Industries du pétrole, de la chimie et du gaz naturel - Compresseurs d'air centrifuges assemblés à multiplicateur intégré (ISO 10442:2002)
L'ISO 10442:2002 spécifie les exigences et fournit des recommandations pour la conception, les matériaux, la fabrication, le contrôle, la mise à l'essai et la préparation pour l'expédition des compresseurs d'air centrifuges à multiplicateur intégré assemblé à vitesse constante, y compris leurs accessoires, utilisés dans les industries du pétrole, de la chimie et du gaz naturel. Elle peut s'appliquer aux utilisations de gaz autres que l'air, non dangereux et non toxiques. Cette norme ne s'applique pas aux machines qui développent une élévation de pression inférieure à 35 kPa au-dessus de la pression atmosphérique, classées comme ventilateurs ou compresseurs.
Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors (ISO 10442:2002)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2004
Petroleum, chemical and gas service industries - Packaged, integrally geared
centrifugal air compressors (ISO 10442:2002)
Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal
air compressors (ISO 10442:2002)
Erdöl-, Chemie- und Erdgasindustrie - Turbo-Luftkompressoranlagen mit integriertem
Getriebe (ISO 10442:2002)
Industries du pétrole, de la chimie et du gaz naturel - Compresseurs d'air centrifuges
assemblés a multiplicateur intégré (ISO 10442:2002)
Ta slovenski standard je istoveten z: EN ISO 10442:2002
ICS:
23.140 .RPSUHVRUMLLQSQHYPDWLþQL Compressors and pneumatic
VWURML machines
75.180.20 Predelovalna oprema Processing equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 10442
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2002
ICS 23.140; 75.180.20
English version
Petroleum, chemical and gas service industries - Packaged,
integrally geared centrifugal air compressors (ISO 10442:2002)
Industries du pétrole, de la chimie et du gaz naturel -
Compresseurs d'air centrifuges assemblés à multiplicateur
intégré (ISO 10442:2002)
This European Standard was approved by CEN on 6 November 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10442:2002 E
worldwide for CEN national Members.
Foreword
This document (EN ISO 10442:2002) has been prepared by Technical Committee ISO/TC 118
"Compressors, pneumatic tools and pneumatic machines" in collaboration with Technical
Committee CEN/TC 12 "Materials, equipment and offshore structures for petroleum and natural
gas industries", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2003, and conflicting national
standards shall be withdrawn at the latest by June 2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
NOTE FROM CMC The foreword is susceptible to be amended on reception of the German
language version. The confirmed or amended foreword, and when appropriate, the normative
annex ZA for the references to international publications with their relevant European
publications will be circulated with the German version.
Endorsement notice
The text of ISO 10442:2002 has been approved by CEN as EN ISO 10442:2002 without any
modifications.
INTERNATIONAL ISO
STANDARD 10442
First edition
2002-12-01
Petroleum, chemical and gas service
industries — Packaged, integrally geared
centrifugal air compressors
Industries du pétrole, de la chimie et du gaz naturel — Compresseurs d'air
centrifuges assemblés à multiplicateur intégré
Reference number
ISO 10442:2002(E)
©
ISO 2002
ISO 10442:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved
ISO 10442:2002(E)
Contents
Foreword . iv
Introduction. v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 2
4 Basic design . 4
4.1 General . 4
4.2 Package. 7
4.3 Integrally geared compressor. 19
4.4 Driver . 33
4.5 Driver-to-compressor coupling and guard. 34
4.6 Intercoolers. 35
5 Accessories . 35
5.1 Aftercooler . 35
5.2 Air intake filter-silencer . 36
5.3 Discharge blowoff silencer . 36
6 Inspection, testing and preparation for shipment . 36
6.1 General . 36
6.2 Inspection . 37
6.3 Testing. 37
6.4 Preparation for shipment. 40
7 Vendor data. 41
7.1 Proposals . 41
7.2 Contract data . 42
Annex A (informative) Data sheets . 46
Annex B (informative) Material specifications for major component parts. 59
Annex C (informative) Diagrams (see ISO 10439). 62
Annex D (normative) Forces and moments . 66
Bibliography. 69
ISO 10442:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10442 was prepared by Technical Committee ISO/TC 118, Compressors, pneumatic tools and pneumatic
machines, in collaboration with Technical Committee ISO/TC 67, Materials, equipment and offshore structures for
petroleum, petrochemical and natural gas industries, Subcommittee SC 6, Processing equipment and systems.
Annex D forms a normative part of this International Standard. Annexes A, B and C are for information only.
iv © ISO 2002 – All rights reserved
ISO 10442:2002(E)
Introduction
This International Standard is based on the American Petroleum Institute's API Std 672, second edition, April 1988.
Some of the content of this International Standard is identical or similar to ISO 10439, which covers centrifugal
compressors for the petroleum, chemical and gas service industries.
Users of this International Standard should be aware that further or differing requirements may be needed for
individual applications. This International Standard is not intended to inhibit a vendor from offering, or the purchaser
from accepting, alternative equipment or engineering solutions for the individual application. This may be
particularly applicable where there is innovative or developing technology. Where an alternative is offered, the
vendor should identify any variations from this International Standard and provide details.
INTERNATIONAL STANDARD ISO 10442:2002(E)
Petroleum, chemical and gas service industries — Packaged,
integrally geared centrifugal air compressors
1 Scope
This International Standard specifies requirements and gives recommendations for the design, materials,
fabrication, inspection, testing and preparation for shipment of constant-speed, packaged, integrally geared
centrifugal air compressors, including their accessories, for use in the petroleum, chemical and gas service
industries. It is also applicable to gas services other than air that are non-hazardous and non-toxic. It is not
applicable to machines that develop a pressure rise of less than 35 kPa above atmospheric pressure, which are
classed as fans or blowers.
NOTE In this International Standard, where practical, US customary units have been included in brackets for information.
2 Normative references
The following normative documents contain provisions which, through reference in this te
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.