EN 12163:2011
(Main)Copper and copper alloys - Rod for general purposes
Copper and copper alloys - Rod for general purposes
This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy rod in the shape of circles, squares, hexagons or octagons, finally produced by drawing or extruding intended for general purposes.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.
Kupfer und Kupferlegierungen - Stangen zur allgemeinen Verwendung
Diese Europäische Norm legt die Zusammensetzung, die Anforderungen an die Eigenschaften und die Grenzabmaße für durch Ziehen oder Pressen endgefertigte Stangen aus Kupferlegierungen in runder, quadratischer, sechseckiger oder achteckiger Form zur allgemeinen Verwendung fest. Der Ablauf der Probenentnahme und die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen dieser Norm sind ebenfalls festgelegt.
Cuivre et alliages de cuivre - Barres pour usages généraux
La présente Norme européenne spécifie la composition, les caractéristiques et les tolérances dimensionnelles des barres en cuivre et alliages de cuivre de forme ronde, carrée, hexagonale ou octogonale, fabriquées par étirage ou filage, destinées à des usages généraux.
Les procédures d'échantillonnage et les méthodes d'essai pour la vérification de la conformité aux prescriptions de la présente Norme européenne sont également spécifiées.
Baker in bakrove zlitine - Palice za splošno uporabo
Dokument določa sestavo, zahteve za lastnosti in odstopke mer za ravne palice iz bakra in bakrovih zlitin za splošno uporabo. Določeni so tudi postopki vzorčenja in metode preskušanja za preverjanje skladnosti z zahtevami tega dokumenta.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine - Palice za splošno uporaboKupfer und Kupferlegierungen - Stangen zur allgemeinen VerwendungCuivre et alliages de cuivre - Barres pour usages générauxCopper and copper alloys - Rod for general purposes77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 12163:2011SIST EN 12163:2011en,fr,de01-oktober-2011SIST EN 12163:2011SLOVENSKI
STANDARDSIST EN 12163:19981DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12163
June 2011 ICS 77.150.30 Supersedes EN 12163:1998English Version
Copper and copper alloys - Rod for general purposes
Cuivre et alliages de cuivre - Barres pour usages généraux Kupfer und Kupferlegierungen - Stangen zur allgemeinen Verwendung This European Standard was approved by CEN on 14 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12163:2011: ESIST EN 12163:2011
Determination of mean depth of dezincification . 33A.1Introduction . 33A.2Procedure . 33A.3Expression of results . 33Bibliography . 35 Figures Figure 1 — Measurement of twist of polygonal rod . 12 Figure A.1 — Example of contiguous fields . 34
Tables Table 1 — Composition of low alloyed copper alloys . 16 Table 2 — Composition of copper-aluminium alloys . 17 Table 3 — Composition of copper-nickel alloys . 17 Table 4 — Composition of copper-nickel-zinc alloys . 17 Table 5 — Composition of copper-tin alloys . 18 Table 6 — Composition of copper-zinc alloys. 18 Table 7 — Composition of complex copper-zinc alloys . 19 Table 8 — Mechanical properties of rod of low alloyed copper alloys . 20 Table 9 — Mechanical properties of rod of copper-aluminium alloys . 22 Table 10 — Mechanical properties of rod of copper-nickel alloys . 23 Table 11 — Mechanical properties of rod of copper-nickel-zinc alloys . 24 Table 12 — Mechanical properties of rod of copper-tin alloys . 25 Table 13 — Mechanical properties of rod of copper-zinc alloys . 26 Table 14 — Mechanical properties of rod of complex copper-zinc alloys . 29 Table 15 — Dimensional tolerances for rod . 31 Table 16 — Tolerances on straightness of rod . 31 Table 17 — Corner radii for square and polygonal rod . 31 Table 18 — Maximum twist of square and polygonal rod . 32 Table 19 — Sampling rate . 32
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.