Extended application of test results on durability of self-closing for fire resistance and/or smoke control doorsets and openable windows - Part 3: Durability of self-closing of steel sliding doorsets

This document is applicable to the following types of steel based doorsets: horizontally sliding single and double leaf doorsets, horizontally sliding single and double leaf telescopic doorsets, vertically sliding single leaf doorsets and vertically sliding single leaf telescopic doorsets as covered by EN 15269-7 or EN 15269-20.
This document prescribes the methodology for extending the application of test results obtained from durability of self-closing test(s) conducted in accordance with EN 12605:2000 and/or EN 1191.
Subject to the completion of the appropriate durability of self-closing test or tests, the extended application can cover all or some of the following non-exhaustive list:
- door leaf (of the sliding doorset and its pass door);
- integrated pass doors;
- wall or ceiling fixed parts or items of the doorset, e.g. frame or suspension systems;
- ventilation grilles and/or louvres;
- glazing for door leaf;
- items of building hardware;
- decorative finishes;
- intumescent, smoke, draught or acoustic seals;
- alternative supporting construction(s).

Erweiterte Anwendung von Prüfergebnissen zur Dauerhaftigkeit der Selbstschließung für Feuerschutz und/oder Rauchschutztüren, -tore und zu öffnende Fenster - Teil 3: Dauerhaftigkeit der Selbstschließung von Schiebetoren aus Stahl

Dieses Dokument ist für die folgenden Arten von Stahltoren anwendbar: horizontal öffnende ein  oder zweiflügelige Schiebetore/ türen, horizontal öffnende ein  oder zweiflügelige Teleskoptore/ türen, vertikal öffnende einflügelige Schiebetore/ türen und vertikal öffnende einflügelige Teleskoptore/ türen, wie in EN 15269 7 oder EN 15269 20 beschrieben.
Dieses Dokument schreibt die Methodik zur Erweiterung der Anwendung von Prüfergebnissen zur Dauerhaftigkeit der Selbstschließung vor, die nach EN 12605:2000 bzw. nach EN 1191 durchgeführt wurden.
In Abhängigkeit von der Durchführung der entsprechenden Prüfung(en) zur Dauerhaftigkeit der Selbstschließung kann die erweiterte Anwendung die nachfolgende nicht-abschließende Auflistung ganz oder auch nur teilweise abdecken:
—   Tür /Torblatt (der Schiebetür/des Schiebetores und deren/dessen Schlupftür);
—   integrierte Schlupftüren;
—   an der Wand oder Decke befestigte Teile oder Elemente der Tür/des Tores, z. B. Rahmen oder Aufhängungssysteme;
—   Lüftungsgitter und/oder  lamellen;
—   Tor /Türblatt-Verglasung;
—   Baubeschläge;
—   dekorative Oberflächenbeschichtungen;
—   dämmschichtbildende Dichtungen sowie Dichtungen zur Behinderung von Rauchdurchtritt (Rauchschutzdichtungen), Durchzug oder Schallübertragung (Schallschutzdichtungen);
—   alternative Tragkonstruktion(en).

Application étendue des résultats d’essais de durabilité de la fermeture automatique des blocs-portes et fenêtres ouvrantes résistants au feu et/ou étanches à la fumée - Partie 3 : Durabilité de la fermeture automatique des blocs-portes coulissants en acier

Le présent document s’applique aux types suivants de blocs-portes à base d’acier : blocs-portes à simple ou à double vantail coulissant horizontalement, blocs-portes télescopiques à simple ou à double vantail coulissant horizontalement, blocs-portes à simple vantail coulissant verticalement et blocs-portes télescopiques à simple vantail coulissant verticalement visés par l’EN 15269-7 ou l’EN 15269-20.
Le présent document établit la méthodologie d’extension de l’application des résultats d’essai obtenus à la suite de l’essai ou des essais de durabilité de la fermeture automatique réalisés conformément à l’EN 12605:2000 et/ou l’EN 1191.
Sous réserve de la réalisation de l’essai ou des essais appropriés de durabilité de la fermeture automatique, l’application étendue peut couvrir tout ou partie des éléments de la liste non exhaustive suivante :
- vantail (du bloc-porte coulissant et de son portillon) ;
- portillons intégrés ;
- éléments ou parties du bloc-porte fixés au mur ou au plafond, par exemple structure ou systèmes de suspension ;
- grilles de ventilation et/ou jalousies ;
- vitrage de vantail ;
- tout élément de quincaillerie intégré ;
- finitions décoratives ;
- joints intumescents, joints d’étanchéité aux fumées, joints d’étanchéité à l’air ou joints acoustiques ;
- autres supports.

Razširjena uporaba rezultatov preskusov trajnosti samozapiranja za požarno odporna in/ali dimotesna vrata in okna, ki se odpirajo - 3. del: Trajnost samozapiranja jeklenih drsnih vrat

Ta dokument se uporablja za naslednje vrste jeklenih vrat: vodoravno drsna vrata (enojna in dvojna), teleskopska vrata (enojna in dvojna) in enojna navpično drsna vrata, zajeta v standardu EN 15269 7 ali EN 15269 20.
Ta dokument predpisuje metodologijo za razširitev uporabe rezultatov, pridobljenih iz preskusov trajnosti samozapiranja, izvedenih v skladu s standardom EN 12605:2017+A1:2020 ali EN 1191.
Razširjena uporaba lahko (glede na opravljene ustrezne preskuse samozapiranja) zajema vse ali nekatere primere iz naslednjega neizčrpnega seznama:
–   vratno krilo;
–   prehodna vrata;
–   stensko/stropno okovje (okvir/sistem vzmetenja);
–   prezračevalne rešetke in/ali žaluzijske lopute;
–   steklo za vratno krilo;
–   elementi stavbnega okovja;
–   okrasni zaključki;
–   intumescentna, dimna, akustična tesnila in tesnila za preprečevanje prepiha;
–   alternativne podporne konstrukcije.

General Information

Status
Published
Publication Date
06-Dec-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
07-Dec-2022
Due Date
26-Aug-2021
Completion Date
07-Dec-2022

Buy Standard

Standard
EN 17020-3:2023
English language
60 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 17020-3:2021
English language
64 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 17020-3:2023
01-april-2023
Razširjena uporaba rezultatov preskusov trajnosti samozapiranja za požarno
odporna in/ali dimotesna vrata in okna, ki se odpirajo - 3. del: Trajnost
samozapiranja jeklenih drsnih vrat
Extended application of test results on durability of self-closing for fire resistance and/or
smoke control doorsets and openable windows - Part 3: Durability of self-closing of steel
sliding doorsets
Erweiterter Anwendungsbereich von Prüfergebnissen zur Dauerhaftigkeit der
Selbstschließung für Feuerschutz- und/oder Rauchschutztüren und zu öffnende Fenster
- Teil 3: Dauerhaftigkeit der Selbstschließung von Schiebetoren aus Stahl
Application étendue des résultats d’essais de durabilité de la fermeture automatique des
blocs-portes et fenêtres ouvrantes résistants au feu et/ou étanches à la fumée - Partie 3
: Durabilité de la fermeture automatique des blocs-portes coulissants en acier
Ta slovenski standard je istoveten z: EN 17020-3:2022
ICS:
13.220.50 Požarna odpornost Fire-resistance of building
gradbenih materialov in materials and elements
elementov
91.060.50 Vrata in okna Doors and windows
SIST EN 17020-3:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 17020-3:2023

---------------------- Page: 2 ----------------------
SIST EN 17020-3:2023


EN 17020-3
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2022
EUROPÄISCHE NORM
ICS 13.220.50; 91.060.50
English Version

Extended application of test results on durability of self-
closing for fire resistance and/or smoke control doorsets
and openable windows - Part 3: Durability of self-closing
of steel sliding doorsets
Application étendue des résultats d'essais de durabilité Erweiterter Anwendungsbereich von Prüfergebnissen
de la fermeture automatique des blocs-portes et zur Dauerhaftigkeit der Selbstschließung für
fenêtres ouvrantes résistants au feu et/ou étanches à la Feuerschutz- und/oder Rauchschutztüren und zu
fumée - Partie 3 : Durabilité de la fermeture öffnende Fenster - Teil 3: Dauerhaftigkeit der
automatique des blocs-portes coulissants en acier Selbstschließung von Schiebetoren aus Stahl
This European Standard was approved by CEN on 24 July 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17020-3:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Determination of the field of extended application . 8
4.1 General . 8
4.2 Procedure for evaluation . 8
4.3 Procedure for maximum field of extended application . 9
4.4 Interpretation of test results . 9
5 Extended application report . 10
6 Classification report . 10
Annex A (normative) Construction parameter variations . 11
Annex B (normative) Construction parameter variation simulation by applying additional
weights . 59
Bibliography . 60

2

---------------------- Page: 4 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
European foreword
This document (EN 17020-3:2022) has been prepared by Technical Committee CEN/TC 127 “Fire safety
in buildings”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2023, and conflicting national standards shall be
withdrawn at the latest by June 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association.
A list of all parts in the EN 17020 series and the EN 15269 series can be found on the CEN website.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
3

---------------------- Page: 5 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
Introduction
The EN 15269 series of standards covering extended application of test results for fire resistance and/or
smoke control for doorsets, shutter assemblies and openable window, including their items of building
hardware, does not yet include the durability of self-closing following an extended application process.
This document is one of the EN 17020 series of standards intended to be used for the purpose of
producing an extended application report based on the evaluation of one or more durability of self-
closing tests. These European Standards may also be used to identify the best selection of test specimens
required to cover a wide range of product variations.
4

---------------------- Page: 6 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
1 Scope
This document is applicable to the following types of steel based doorsets: horizontally sliding single and
double leaf doorsets, horizontally sliding single and double leaf telescopic doorsets, vertically sliding
single leaf doorsets and vertically sliding single leaf telescopic doorsets as covered by EN 15269-7 or
EN 15269-20.
This document prescribes the methodology for extending the application of test results obtained from
durability of self-closing test(s) conducted in accordance with EN 12605:2000 and/or EN 1191.
Subject to the completion of the appropriate durability of self-closing test or tests, the extended
application can cover all or some of the following non-exhaustive list:
— door leaf (of the sliding doorset and its pass door);
— integrated pass doors;
— wall or ceiling fixed parts or items of the doorset, e.g. frame or suspension systems;
— ventilation grilles and/or louvres;
— glazing for door leaf;
— items of building hardware;
— decorative finishes;
— intumescent, smoke, draught or acoustic seals;
— alternative supporting construction(s).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 179, Building hardware - Emergency exit devices operated by a lever handle or push pad, for use on
escape routes - Requirements and test methods
EN 1125, Building hardware - Panic exit devices operated by a horizontal bar, for use on escape routes -
Requirements and test methods
EN 1154, Building hardware - Controlled door closing devices - Requirements and test methods
EN 1155, Building hardware - Electrically powered hold-open devices for swing doors - Requirements and
test methods
EN 1191, Windows and doors - Resistance to repeated opening and closing - Test method
EN 1363-1, Fire resistance tests - Part 1: General requirements
EN 1363-2, Fire resistance tests - Part 2: Alternative and additional procedures
EN 14637, Building hardware - Electrically controlled hold-open systems for fire/smoke door assemblies -
Requirements, test methods, application and maintenance
5

---------------------- Page: 7 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
EN 1634-1, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and
elements of building hardware - Part 1: Fire resistance test for door and shutter assemblies and openable
windows
EN 1634-3, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and
elements of building hardware - Part 3: Smoke control test for door and shutter assemblies
EN 1906, Building hardware - Lever handles and knob furniture - Requirements and test methods
1
EN 1935:2002 , Building hardware - Single-axis hinges - Requirements and test methods
EN 12209, Building hardware - Mechanically operated locks and locking plates - Requirements and test
methods
EN 12433-1, Industrial, commercial and garage doors and gates - Terminology - Part 1: Types of doors
EN 12433-2, Industrial, commercial and garage doors and gates - Terminology - Part 2: Parts of doors
EN 12605:2000, Industrial, commercial and garage doors and gates - Mechanical aspects - Test methods
EN 13501-1, Fire classification of construction products and building elements - Part 1: Classification using
data from reaction to fire tests
EN 13501-2, Fire classification of construction products and building elements - Part 2: Classification using
data from fire resistance tests, excluding ventilation services
EN 14846, Building hardware - Locks and latches - Electromechanically operated locks and striking plates -
Requirements and test methods
EN 15269-1, Extended application of test results for fire resistance and/or smoke control for door, shutter
and openable window assemblies, including their elements of building hardware - Part 1: General
requirements
EN 15269-7, Extended application of test results for fire resistance and/or smoke control for door, shutter
and openable window assemblies, including their elements of building hardware - Part 7: Fire resistance for
steel sliding doorsets
EN 15269-20, Extended application of test results for fire resistance and/or smoke control for door, shutter
and openable window assemblies, including their elements of building hardware - Part 20: Smoke control
for doors, shutters, operable fabric curtains and openable windows
2
, Building hardware - Requirements and test methods - Multipoint locks, latches and locking
EN 15685
plates - Characteristics and test methods
EN ISO 13943, Fire safety - Vocabulary (ISO 13943)

1
As impacted by EN 1935:2002/AC:2003.
2
Under preparation. Stage at the time of publication: prEN 15685:2022.
6

---------------------- Page: 8 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1191, EN 1363-1, EN 1363-2,
EN 1634-1, EN 1634-3, EN 15269-1, EN 15269-7, EN 15269-20, EN 12433-1, EN 12433-2 and
EN ISO 13943 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
full scale test
test of a full size doorset in accordance with EN 12605:2000 and/or EN 1191
3.2
panel
part of a leaf or element of a doorset as indicated as 1 in Figures 1 and 2

Key
1 panel
2 leaf
3 element
Figure 1 — Double leaf telescopic sliding doorset

Key
1 panel
2 leaf
Figure 2 — Double leaf sliding doorset
3.3
leaf
movable part of a doorset indicated as 2 in Figures 1 and 2
7

---------------------- Page: 9 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
3.4
element
part of a leaf indicated as 3 in Figure 1
3.5
add
put an additional component to the doorset which has not been tested as a part of the original doorset
3.6
remove
take a component away which has been tested as a part of the original doorset
3.7
alternative
variation intended by the application of EXAP rules where the original construction parameter tested
shall be substituted by another one either by change, interchange or exchange
Note 1 to entry: Finally, the alternatives are those variations that are permitted by the EXAP report.
4 Determination of the field of extended application
4.1 General
4.1.1 Before there can be any consideration for extended application, the doorset shall have been tested
in accordance with EN 12605:2000 and/or EN 1191, as appropriate, to achieve a test result which could
generate a classification for the durability of self-closing in accordance with EN 13501-2 for the required
number of test cycles.
4.1.2 A review of the doorset construction parameters can indicate, that one or more characteristics
can be improved by a particular parameter variation. All evaluations shall be made on the basis of
retaining the classifications for the durability of self-closing obtainable from testing to EN 12605:2000
and/or EN 1191, as appropriate, including those with a lower number of opening and closing cycles.
However, this shall never lead to an increased classification for any specific parameter beyond that
achieved during any one test unless specifically identified in the relevant Construction Parameter
Variation tables.
4.1.3 If, when following the extended application procedure, any part of the classified product cannot
be achieved by extended application rules, that part shall be omitted from the subsequent extended
application report and classification report.
4.2 Procedure for evaluation
4.2.1 Identify the variations from the original test specimen(s) which are required to be covered by an
extended application report. Ensure that the variation(s) do(es) not prevent the doorset and/or
integrated hinged pass doors from self-closing.
4.2.2 Locate the variations in the appropriate parameter variation by reference to columns (1) and (2)
of Annex A, Table A.1.
4.2.3 Establish from the contents of column (3) of Annex A, Table A.1 whether any extended application
is available without the need for further testing.
4.2.4 Where this is deemed to be possible, this can be recorded in the extended application report
together with any appropriate restrictions and the stated rules from column (3) in Annex A, Table A.1.
8

---------------------- Page: 10 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
4.2.5 Where the variations required can only be achieved from additional testing according to
column (4), the additional test can be made on a test specimen similar to the original test specimen
against which the extended application is sought. Alternatively, column (4) in Table A.1 identifies an
option for alternative testing and relevant test parameters.
4.3 Procedure for maximum field of extended application
4.3.1 It is possible to provide a limited field of extended application from the results of a single test.
However, where a manufacturer intends to produce a range of sliding doorsets incorporating single leaf
doorsets and also double leaf doorsets, with or without pass doors, with or without glazing, with
alternative items of building hardware, etc., it is recommended that careful consideration is given to the
complete range of doorset designs and options in order to minimize the testing required before testing
commences.
4.3.2 Establish all the parameter variations, which are required to be part of the product range.
4.3.3 Determine which are the most important specification requirements and incorporate as many as
possible into the test specimen(s) for the first tests in the series.
4.3.4 Conduct the first durability of self-closing test or a series of tests and then establish, which of the
original desired parameter variations have not been covered by this test(s).
4.3.5 Identify these parameter variations in Annex A, Table A.1 and establish if any extended
application is possible without further testing.
4.3.6 Record this for the extended application report together with any restrictions and rules given in
column (3) in Annex A, Table A.1.
4.3.7 Evaluate which, if any, of the desired parameter variations have not been covered by the initial
field of extended application derived from 4.3.6 above.
4.3.8 Determine if the product range is to include only single leaf doorsets or if the range is to also
include double leaf configurations. Where only single leaf doorsets are to be part of the product range,
the outstanding construction parameter variations shall only be incorporated into specimens for the
single leaf doorsets. Where single leaf and double leaf doorsets are to be included in the product range,
the outstanding construction parameter variations for the extended application of single leaf doorsets
may be incorporated into either repeated single leaf doorset tests or, in the weakest option, as defined in
column (4) of the table in Annex A, Table A.1, double leaf doorset configurations.
4.3.9 Select the required outstanding parameter variations from column (1) and column (2) of Annex A,
Table A.1 and observe from column (4) of Annex A, Table A.1 which are the most appropriate weakest
test specimen options for further testing.
4.3.10 If the complete selection of required parameter variations has not been covered by the tests
completed in accordance with 4.3.8 and 4.3.9 above, then an appropriate test or tests may be carried out
with the additional product variations incorporated.
4.4 Interpretation of test results
4.4.1 In order to maximize the field of extended application, it is important that the test reports shall
record details of any failures occurred throughout the test duration.
9

---------------------- Page: 11 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
4.4.2 Where a series of tests have been conducted, the field of extended application shall be based on
the lowest performance achieved from the complete series of tests unless premature failure has been
attributed to one or more specific construction parameter variations(s).
4.4.3 Where it has been possible, to identify specific parameter failures, the extended application for
all other construction parameter variations can be based on the performance achieved after isolating the
premature failure(s). The failed parameter shall be omitted from the extended application report and the
subsequent classification report.
5 Extended application report
Prepare an extended application report in accordance with the requirements of EN 15269-1 based on the
results of evaluations in accordance with the above.
6 Classification report
The classification report shall be determined from the results of the extended application report and shall
be presented in accordance with EN 13501-2.
10

---------------------- Page: 12 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
Annex A
(normative)

Construction parameter variations
Table A.1 below is designed to be used by experts competent in the field of fire resistance, smoke control
and durability of self-closing testing of sliding doorsets and/or integrated hinged pass doors, as
appropriate.
The table shall only be used to assess a field of extended application when at least one positive durability
of self-closing test to EN 12605:2000 and/or EN 1191, as appropriate, has generated a classification
according to EN 13501-2 for the required number of test cycles.
The first two columns identify possible variations to the construction details of the specimen tested. It is
presupposed that the variations do not restrain the doorset and/or its pass door from closing.
Column (3) leads to the judgement of the possibility of extending the field of application.
Where additional tests are deemed to be necessary, the type of test specimen approved for incorporation
of the changed parameter is defined in column (4). Where it is possible to use information from tests
performed on one configuration for evidence on a different configuration, this allowance has been made
in order to reduce the overall number of tests required for extended application evaluation e.g. single leaf
doorsets to double leaf doorsets.
Where an additional test is required in column (4), the test is a full scale test unless otherwise specified.
In order to maximize the possible field of application from a minimum number of tests, the parameter
changes have been spread over a series of test specimens. Where more than a single parameter variation
is required, the influence on other variations shall also be taken into account.
All parameter variations in Table A.1 presuppose that the total mass of doorset and/or its pass door does
not exceed the maximum mass having been tested. For simulation of a higher mass of the varied doorset
the test specimen for durability of self-closing test can be loaded with additional weight(s) attached to
the leaf according to the rules in Annex B.
11

---------------------- Page: 13 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
Table A.1 — Construction parameter variations
Construction Parameter Variation Possibility of extension Additional Evidence Required
(1) (2) (3) (4)
A Door leaf
A.1 General
Possible providing the overlap of the single leaf
doorset (door leaf to frame) is similar to the
overlap of the double doorset (meeting edge) and
A.1.1 Number of door leaves (not
all the constructional details have been tested (in
Single leaf doorset from double leaf Additional test single leaf
applicable for vertically sliding
the double doorset), otherwise not possible
doorset test doorset
doorsets)
without an additional test.
Any size variations of door leaf shall be in line
with A.2.1 to A.2.4 incl.
A.1.2 Number of door leaves (not
Double leaf doorset from single leaf Additional test double leaf
applicable for vertically sliding Not possible without an additional test
doorset test doorset or double leaf telescopic
doors)
Possible providing all constructional details have
A.1.3 Number of elements of single leaf Additional test single or double
Decrease been tested, otherwise not possible without an
telescopic doorsets, leaf telescopic doorset
additional test
A.1.4 Number of elements of single leaf Additional test single or double
Increase Not possible without an additional test
telescopic doorsets, leaf telescopic doorset
Possible providing all constructional details have
A.1.5 Number of elements of double leaf been tested and the reduction of elements is the Additional test double leaf
Decrease
telescopic doorsets – See Figure A.1 same for both door leaves, otherwise not possible telescopic doorset
without an additional test
A.1.6 Number of elements of double leaf
Additional test double leaf
telescopic doors, (not applicable for Increase Not possible without an additional test
telescopic doorset
vertically sliding doorsets)
12

---------------------- Page: 14 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
Construction Parameter Variation Possibility of extension Additional Evidence Required
(1) (2) (3) (4)
Possible if tested at least one leaf (single, primary
or secondary) with the minimum of two panels
A.1.7 Number of panels per door leaf or Additional test single or double
and the intended jointing technique centrally
Increase
element – See Figure A.2 leaf doorset
located in the door leaf.
Otherwise not possible without an additional test
A.1.8 Number of panels per door leaf or
Decrease Possible -
element – See Figure A.3
A.1.9  Ventilation grilles (louvres) in door Possible providing the requirements of Annex B
Additional test single or double
leaf tested without ventilation grille Add are fulfilled, otherwise not possible without an
leaf doorset
(louvers) additional test
Possible providing the requirements of Annex B
A.1.10 Ventilation grilles (louvres) in door Additional test single or double
Remove are fulfilled, otherwise not possible without an
leaf leaf doorset
additional test
A.1.11 Location of Ventilation grilles
(louvres) in door leaf tested with Alternative Possible -
ventilation grille (louvres)
A.1.12 Size of ventilation grilles (louvres) in Increase/decrease Possible providing the requirements of Annex B
Additional test single or double
door leaf tested with ventilation are fulfilled, otherwise not possible without an
leaf doorset
grille (louvres) additional test
A.2 Size variations/single or multiple panel construction
A.2.1 Size (area, width, height) of door leaf Decrease Possible -
Possible providing the requirements of Annex B Additional test double for single
A.2.2 Width of door leaf – See Figure A.4 Increase are fulfilled, otherwise not possible without an and double leaf doorsets or
additional test single for single leaf doorsets
Possible providing the requirements of Annex B Additional test double for single
A.2.3 Height of door leaf – See Figure A.5 Increase are fulfilled, otherwise not possible without an and double leaf doorsets or
additional test single for single leaf doorsets
13

---------------------- Page: 15 ----------------------
SIST EN 17020-3:2023
EN 17020-3:2022 (E)
Construction Parameter Variation Possibility of extension Additional Evidence Required
(1) (2) (3) (4)
Possible providing the requirements of Annex B Additional test double for single
A.2.4 Area of door leaf Increase are fulfilled, otherwise not possible without an and double leaf doorsets or
additional test single for single leaf doorsets
A.2.5 Width of vertical door leaf panel for
a sliding doorset with more than one Decrease Possible -
panel
Possible providing the requirements of Annex B Additional test double for single
A.2.6 Height of vertical door leaf panel Increase are fulfilled, otherwise not possible without an and double leaf doorsets or
additional test single for single leaf doorsets
A.2.7 Height of vertical door leaf panel Decrease Possible -
Possible providing the requirements of Annex B Additional test double for single
A.2.8 Width of vertical door leaf panel Increase are fulfilled, otherwise not possible without an and double leaf doorsets or
additional test single for single leaf doorsets
Possible providing the requirements of Annex B Additional test double for single
A.2.9 Area of vertical door leaf panel Increase are fulfilled, otherwise not possible without an and double leaf doorsets or
additional test single for single leaf doorsets
A.2.10 Number of horizontal joints between
Increase Possible -
panels
Possibl
...

SLOVENSKI STANDARD
oSIST prEN 17020-3:2021
01-junij-2021
Razširjena uporaba rezultatov preskusov trajnosti samozapiranja za požarno
odporna in/ali dimotesna vrata in okna, ki se odpirajo - 3. del: Trajnost
samozapiranja jeklenih drsnih vrat
Extended application of test results on durability of self-closing for fire resistance and/or
smoke control doorsets and openable windows - Part 3: Durability of self-closing of steel
sliding doorsets
Erweiterter Anwendungsbereich von Prüfergebnissen zur Dauerhaftigkeit der
Selbstschließung für Feuerschutz und/oder Rauchschutztüren und zu öffnende Fenster
- Teil 3: Dauerhaftigkeit der Selbstschließung von Schiebetoren aus Stahl
Application étendue des résultats d ’essais de durabilité de la fermeture automatique des
blocs-portes et fenêtres ouvrantes résistants au feu et/ou étanches à la fumée - Partie 3
: Durabilité de la fermeture automatique des blocs-portes coulissants en acier
Ta slovenski standard je istoveten z: prEN 17020-3
ICS:
13.220.50 Požarna odpornost Fire-resistance of building
gradbenih materialov in materials and elements
elementov
91.060.50 Vrata in okna Doors and windows
oSIST prEN 17020-3:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 17020-3:2021

---------------------- Page: 2 ----------------------
oSIST prEN 17020-3:2021


DRAFT
EUROPEAN STANDARD
prEN 17020-3
NORME EUROPÉENNE

EUROPÄISCHE NORM

May 2021
ICS 13.220.50; 91.060.50
English Version

Extended application of test results on durability of self-
closing for fire resistance and/or smoke control doorsets
and openable windows - Part 3: Durability of self-closing
of steel sliding doorsets
 Erweiterter Anwendungsbereich von Prüfergebnissen
zur Dauerhaftigkeit der Selbstschließung für
Feuerschutz- und/oder Rauchschutztüren und zu
öffnende Fenster - Teil 3: Dauerhaftigkeit der
Selbstschließung von Schiebetoren aus Stahl
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 127.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17020-3:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Determination of the field of extended application . 7
4.1 General . 7
4.2 Procedure for evaluation . 8
4.3 Procedure for maximum field of extended application . 8
4.4 Interpretation of test results . 9
5 Extended application report . 9
6 Classification report . 9
Annex A (normative) Construction parameter variations . 10
Annex B (normative) Construction parameter variation simulation by applying additional
weights . 63
Bibliography . 64
2

---------------------- Page: 4 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
European foreword
This document (prEN 17020-3:2021) has been prepared by Technical Committee CEN/TC 127 “Fire
safety in buildings”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
A list of all parts in the EN 17020 series can be found on the CEN website.
3

---------------------- Page: 5 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
Introduction
The EN 15269 series of standards covering extended application of test results for fire resistance and/or
smoke control for door, shutter and openable window assemblies, including their elements of building
hardware, does not include the durability of self-closing of the doorsets following an extended application
process. This document is one of the EN 17020 series of standards intended to be used for the purpose of
producing an extended application report based on the evaluation of one or more durability of self-
closing tests. These European Standards may also be used to identify the best selection of test specimens
required to cover a wide range of product variations.
Before there can be any consideration for extended application, the doorset should have been tested in
accordance with EN 12605:2017+A1:2020 or EN 1191 to achieve a test result which could generate a
classification in accordance with EN 13501-2 and EN 16034 at least equal to the classification
subsequently required from extended application considerations.
4

---------------------- Page: 6 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
1 Scope
This document is applicable to the following types of steel based doorsets: horizontally sliding doorsets
(single and double), telescopic doorsets (single and double) and single vertically sliding doorsets as
covered by EN 15269-7 or EN 15269-20.
This document prescribes the methodology for extending the application of test results obtained from
durability of self-closing test(s) conducted in accordance with EN 12605:2017+A1:2020 or EN 1191.
Subject to the completion of the appropriate self-closing test(s), the extended application can cover all or
some of the following non-exhaustive list:
— door leaf;
— pass doors;
— wall/ceiling fixed elements (frame/suspension system);
— ventilation grilles and/or louvres;
— glazing for door leaf;
— items of building hardware;
— decorative finishes;
— intumescent, smoke, draught or acoustic seals;
— alternative supporting construction(s).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 1191, Windows and doors - Resistance to repeated opening and closing - Test method
EN 1363-1, Fire resistance tests - Part 1: General requirements
EN 1363-2, Fire resistance tests - Part 2: Alternative and additional procedures
EN 1634-1, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and
elements of building hardware - Part 1: Fire resistance test for door and shutter assemblies and openable
windows
EN 1634-3, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and
elements of building hardware - Part 3: Smoke control test for door and shutter assemblies
EN 12209, Building hardware - Mechanically operated locks and locking plates - Requirements and test
methods
EN 12433-1, Industrial, commercial and garage doors and gates - Terminology - Part 1: Types of doors
EN 12433-2, Industrial, commercial and garage doors and gates - Terminology - Part 2: Parts of doors
5

---------------------- Page: 7 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
EN 12605:2017+A1:2020, Industrial, commercial and garage doors and gates - Mechanical aspects - Test
methods
EN 13501-2, Fire classification of construction products and building elements - Part 2: Classification using
data from fire resistance tests, excluding ventilation services
EN 14846, Building hardware - Locks and latches - Electromechanically operated locks and striking plates
- Requirements and test methods
EN 15269-1, Extended application of test results for fire resistance and/or smoke control for door, shutter
and openable window assemblies, including their elements of building hardware - Part 1: General
requirements
EN 15269-7, Extended application of test results for fire resistance and/or smoke control for door, shutter
and openable window assemblies, including their elements of building hardware - Part 7: Fire resistance for
steel sliding doorsets
EN 15685:2015, Building hardware – Multipoint locks, latches and locking plates - Requirements and test
methods
EN ISO 13943, Fire safety - Vocabulary (ISO 13943)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1191, EN 1363-1,
EN 1363-2, EN 1634-1, EN 1634-3, EN 15269-1, EN 15269-7, EN 12433-1, EN 12433-2 and
EN ISO 13943 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/ui
— IEC Electropedia: available at http://www.electropedia.org/
3.1
full scale test
test of a full size doorset in accordance with EN 12605:2017+A1:2020 or EN 1191
3.2
panel
part of a leaf or element of a doorset indicated as 1 in Figures 1 and 2
6

---------------------- Page: 8 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)

Key
1 panel
2 leaf
3 element
Figure 1 — Double leaf telescopic door

Key
1 panel
2 leaf
Figure 2 — Double leaf sliding door
3.3
leaf
part of a doorset indicated as 2 in Figures 1 and 2
3.4
element
part of a leaf indicated as 3 in Figure 1
4 Determination of the field of extended application
4.1 General
4.1.1 Before there can be any consideration for extended application, the doorset shall have been tested
in accordance with EN 12605:2017+A1:2020 or EN 1191 to achieve a test result which could generate a
classification in accordance with EN 13501-2 and/or correspond to a use category according to
EN 16034.
4.1.2 A review of the doorset construction parameters can indicate, that one or more characteristics
can be improved by a particular parameter variation. All evaluations shall be made on the basis of
retaining the classifications obtainable from testing to EN 12605:2017+A1:2020 and/or EN 1191,
including those with a lower number of opening and closing cycles. However, this shall never lead to an
increased classification for any specific parameter beyond that achieved during any one test unless
specifically identified in the relevant Construction Parameter Variation tables.
7

---------------------- Page: 9 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
4.1.3 If, when following the extended application procedure, any part of the classified product cannot
be achieved by extended application rules, that part shall be omitted from the subsequent extended
application report and classification report.
4.2 Procedure for evaluation
4.2.1 Identify the variations from the original test specimen(s) which are required to be covered by an
extended application report.
4.2.2 Locate the variations in the appropriate parameter variation by reference to columns (1) and (2)
of Annex A, Table A.1.
4.2.3 Establish from the contents of column (3) of Annex A, Table A.1 whether any extended application
is available without the need for further testing.
4.2.4 Where this is deemed to be possible, this can be recorded in the extended application report
together with any appropriate restrictions and the stated rules from column (3) in Annex A, Table A.1.
4.2.5 Where the variations required can only be achieved from additional testing according to
column (4), the additional test can be made on a similar specimen type to the original test against which
the extended application is sought. Alternatively, column (4) in Table A.1 identifies an option for
alternative testing and relevant test parameters.
4.3 Procedure for maximum field of extended application
4.3.1 It is possible to provide a limited field of extended application from the results of a single test.
However, where a manufacturer intends to produce a range of sliding doors incorporating single leaf
door assemblies and also double leaf door assemblies, with or without pass doors, with or without
glazing, with alternative items of building hardware, etc., it is recommended that careful consideration is
given to the complete range of doorset designs and options in order to minimize the testing required
before testing commences.
4.3.2 Establish all the parameter variations, which are required to be part of the product range.
4.3.3 Determine which are the most important specification requirements and incorporate as many as
possible into the specimen(s) for the first tests in the series.
4.3.4 Conduct the first durability test or a series of tests and then establish, which of the original desired
parameter variations have not been covered by this test(s).
4.3.5 Identify these parameter variations in Annex A, Table A.1 and establish if any extended
application is possible without further testing.
4.3.6 Record this for the extended application report together with any restrictions and rules given in
column (3) in Annex A, Table A.1.
4.3.7 Evaluate which, if any, of the desired parameter variations have not been covered by the initial
field of extended application derived from 4.3.6 above.
4.3.8 Determine if the product range is to include only single leaf doorsets or if the range is to also
include double leaf configurations. Where only single doorsets are to be part of the product range, the
outstanding construction parameter variations shall only be incorporated into specimens for the single
leaf doorsets. Where single leaf and double leaf doorsets are to be included in the product range, the
outstanding construction parameter variations for the extended application of single leaf doorsets may
8

---------------------- Page: 10 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
be incorporated into either repeated single leaf doorset tests or, in the weakest option, as defined in
column (4) of the table in Annex A, Table A.1, double leaf doorset configurations.
4.3.9 Select the required outstanding parameter variations from column (1) and column (2) of Annex A,
Table A.1 and observe from column (4) of Annex A, Table A.1 which are the most appropriate weakest
specimen options for further testing.
4.3.10 If the complete selection of required parameter variations has not been covered by the tests
completed in accordance with 4.3.8 and 4.3.9 above, then an appropriate test or tests may be carried out
with the additional product variations incorporated.
4.4 Interpretation of test results
4.4.1 In order to maximize the field of extended application, it is important that the test reports shall
record details of any failures occurred throughout the test duration.
4.4.2 Where a series of tests have been conducted, the field of extended application shall be based on
the lowest performance achieved from the complete series of tests unless premature failure has been
attributed to one or more specific construction parameter variations.
4.4.3 Where it has been possible, to identify specific parameter failures, the extended application for
all other construction parameter variations can be based on the performance achieved after isolating the
premature failure(s).
5 Extended application report
Prepare an extended application report in accordance with the requirements of EN 15269-1 based on the
results of evaluations in accordance with the above.
6 Classification report
The classification report shall be determined from the results of the extended application report and shall
be presented in accordance with EN 13501-2:2016, Annex A.
9

---------------------- Page: 11 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
Annex A
(normative)

Construction parameter variations
Table A.1 below is designed to be used by experts competent in the field of fire resistance and self-closing
durability testing of steel sliding doorsets.
The table shall only be used to assess a field of extended application when at least one positive self-closing
durability test to EN 12605:2017+A1:2020 or EN 1191 has generated a classification according to
EN 13501-2 and EN 16034.
The first two columns identify possible variations to the construction details of the specimen tested. It is
presupposed that the variation does not restrain the door closing.
Column (3) leads to the judgement of the possibility of extending the field of application.
Where additional tests are deemed to be necessary, the type of specimen approved for incorporation of
the changed parameter is defined in column (4). Where it is possible to use information from tests
performed on one configuration for evidence on a different configuration, this allowance has been made
in order to reduce the overall number of tests required for extended application evaluation e.g. single leaf
doorsets to double leaf doorsets.
Where an additional test is required in column (4), the test is a full scale test unless otherwise specified.
In order to maximize the possible field of application from a minimum number of tests, the parameter
changes have been spread over a series of test specimens. Where more than a single parameter variation
is required, the influence on other variations shall also be taken into account.
10

---------------------- Page: 12 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
Table A.1 — Construction parameter variations
Construction Parameter Variation Possibility of extension Additional Evidence Required
(1) (2) (3) (4)
A Door leaf
A.1 General
Possible providing the overlap of the single leaf
door is similar to the overlap of the double door
(meeting edge) and all the constructional details
A.1.1 Number of leaves (not
Single leaf from double
have been tested (in the double door), otherwise
applicable for vertically Additional test single leaf doorset
leaf door test
not possible without an additional test.
sliding doors)
Any size variations of door leaf shall be in line
with A.2.1 to A.2.4 incl.
A.1.2 Number of leaves (not
Double leaf from single Additional test double leaf doorset
applicable for vertically Not possible without an additional test
leaf door test or double leaf telescopic
sliding doors)
A.1.3 Number of elements of Possible providing all constructional details have
Additional test single or double
telescopic doors, single Decrease been tested, otherwise not possible without an
leaf telescopic
leaf additional test
A.1.4 Number of elements of
Additional test single or double
telescopic doors, single Increase Not possible without an additional test
leaf telescopic
leaf
Possible providing all constructional details have
A.1.5 Number of elements of
been tested and the reduction of elements is the Additional test double leaf
telescopic doors, double Decrease
same for both leaves, otherwise not possible telescopic
leaf — See Figure A.1
without an additional test
A.1.6 Number of elements of
telescopic doors, double Additional test double leaf
Increase Not possible without an additional test
leaf (not applicable for telescopic
vertically sliding doors)
11

---------------------- Page: 13 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
Construction Parameter Variation Possibility of extension Additional Evidence Required
(1) (2) (3) (4)
Possible if tested at least one leaf (single, primary
or secondary) with the minimum of two panels
A.1.7 Number of panels per
Additional test single or double
and the intended jointing technique centrally
leaf/element- See Add
leaf doorset
located in the door leaf.
Figure A.2
Otherwise not possible without an additional test
A.1.8 Number of panels per
leaf/element- See Reduce Possible -
Figure A.3
A.1.9 Ventilation grilles Possible providing the requirements of Annex B
Additional test single or double
(louvres) in door leaf Add are fulfilled, otherwise not possible without an
leaf doorset
tested without ventilation additional test
A.1.10 Ventilation grilles
Remove Possible -
(louvres) in door leaf
A.1.11 Ventilation grilles
(louvres) in door leaf
Change of Location Possible -
tested with ventilation
grille
Smaller size/Larger size Smaller size: Possible
A.1.12 Ventilation grilles
(louvres) in door leaf Additional test single or double
Larger size: possible providing the requirements
tested with ventilation leaf doorset
of Annex B are fulfilled, otherwise not possible
grille
without an additional test
A.2 Size variations/single or multiple panel construction
A.2.1 Size (area, width, height)
Decrease Possible -
of door leaf
Possible providing the requirements of Annex B Additional test double for single
A.2.2 Width of door leaf — See
Increase are fulfilled, otherwise not possible without an and double leaf door sets or single
Figure A.4
additional test for single leaf door sets
12

---------------------- Page: 14 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
Construction Parameter Variation Possibility of extension Additional Evidence Required
(1) (2) (3) (4)
Possible providing the requirements of Annex B Additional test double for single
A.2.3 Height of door leaf — See
Increase are fulfilled, otherwise not possible without an and double leaf door sets or single
Figure A.5
additional test for single leaf door sets
Possible providing the requirements of Annex B Additional test double for single
A.2.4 Area of door leaf Increase are fulfilled, otherwise not possible without an and double leaf door sets or single
additional test for single leaf door sets
A.2.5 Width of vertical door leaf
panel for a sliding door Decrease Possible -
with more than one panel
Possible providing the requirements of Annex B Additional test double for single
A.2.6 Height of vertical door
Increase are fulfilled, otherwise not possible without an and double leaf door sets or single
leaf panel
additional test for single leaf door sets
A.2.7 Height of vertical door
Decrease Possible -
leaf panel
Possible providing the requirements of Annex B Additional test double for single
A.2.8 Width of vertical door leaf
Increase are fulfilled, otherwise not possible without an and double leaf door sets or single
panel
additional test for single leaf door sets
Possible providing the requirements of Annex B Additional test double for single
A.2.9 Area of vertical door leaf
Increase are fulfilled, otherwise not possible without an and double leaf door sets or single
panel
additional test for single leaf door sets
A.2.10 Number of horizontal
Increase Possible -
joints between panels
Possible
A.2.11 Number of horizontal
decrease -
joints between panels

13

---------------------- Page: 15 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
Construction Parameter Variation Possibility of extension Additional Evidence Required
(1) (2) (3) (4)
Additional test double for single
Possible providing the requirements of Annex B
and double leaf door sets or single
are fulfilled and by a maximum of 25 %,
A.2.12 Thickness of the door leaf increase
for single leaf door sets
otherwise not possible without an additional test

Additional test double for single
Possible by a maximum of 25 %,
A.2.13 Thickness of the door leaf Decrease and double leaf door sets or single
otherwise not possible without an additional test
for single leaf door sets
A.3 Materials and constructions
Possible providing the requirements of Annex B Additional test double for single
A.3.1 Density of core material Increase are fulfilled, otherwise not possible without an and double leaf door sets or single
additional test for single leaf door sets
A.3.2 Density of core material Decrease Possible -
Possible providing the requirements of Annex B Additional test double for single
A.3.3 Thickness of core
Increase are fulfilled, otherwise not possible without an and double leaf door sets or single
material
additional test for single leaf door sets
A.3.4 Thickness of core
Decrease Possible -
material
A.3.5 Pattern of core material Increase number of
Possible -
— See Figure A.6 pieces
A.3.6 Pattern of core material Decrease number of
Possible -
— See Figure A.7 pieces
A.3.7 Number of layers of
identical core material — Increase Possible -
See Figure A.8
14

---------------------- Page: 16 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
Construction Parameter Variation Possibility of extension Additional Evidence Required
(1) (2) (3) (4)
A.3.8 Number of layers of
identical core material — Decrease Possible -
See Figure A.9
A.3.9 Number of layers of
different materials — See Increase Possible -
Figure A.10
A.3.10 Number of layers of
different materials — See Decrease Possible -
Figure A.11
Change of
A.3.11 Core material (single
supplier/manufacturer of
thickness or in
identical material with Possible -
combination of different
identical composition
layers)
and properties
A.3.12 Type of core material
(single thickness or in
Alternative composition Possible -
combination of different
layers)
2
A.3.13 Amount of adhesives/m
– Products < Euroclass Increase Possible -
i
A1
2
A.3.14 Amount of adhesives/m
Possible by a maximum of 50 %
Additional test single or double
– Products < Euroclass Decrease
leaf doorset
otherwise not possible without an additional test
i
A1

i
The term "Euroclass A1" stands for the reaction to fire class "A1" according to EN 13501-1.
15

---------------------- Page: 17 ----------------------
oSIST prEN 17020-3:2021
prEN 17020-3:2021 (E)
Construction Parameter Variation Possibility of extension Additional Evidence Required
(1) (2) (3) (4)
2
A.3.15 Amount of adhesives/m
– Products of Euroclass Increase Possible -
i
A1
2
A.3.16 Amount of adhesives/m
Possible by a maximum of 50 %
Additional test single or double
– Products of Euroclass Decrease
leaf doorset
otherwise not possible without an additional test
i
A1
Change of
supplier/manufacturer of
A.3.17 Type of adhesives identical material with Possible -
identical composition
and properties
A.3.18 Type of adhesives Alternative composition Possible -
A.3.19 Metal armour sheet
Possible providing the requirements of Annex B Additional test double for single
(internally or externally
Add are fulfilled, otherwise not possible without an and double leaf door sets or single
mounted) — See
additional test for single leaf door sets
Figure A.12
A.3.20 Metal armour sheet
(internally or externally
Remove Possib
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.