EN 507:2019
(Main)Roofing and cladding products from metal sheet - Specification for fully supported products of aluminium sheet
Roofing and cladding products from metal sheet - Specification for fully supported products of aluminium sheet
This document specifies requirements for roofing and cladding products used for assembly into coverings for wall claddings, linings and pitched roofs, made from aluminium sheet with or without additional surface treatment (organic coating or anodising).
This document establishes general characteristics, definitions and labelling of the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. Products can be prefabricated or semi-formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam roofs).
This document applies to all discontinuously laid and fully supported roofing and cladding products made of aluminium sheets. No requirements for supporting construction, design of roof system and execution of connections and flashings are included.
This document does not apply to self-supporting aluminium sheets that are covered by EN 508-2.
Dachdeckungs- und Wandbekleidungselemente aus Metallblech - Festlegungen für vollflächig unterstützte Bedachungselemente aus Aluminiumblech
Das vorliegende Dokument legt die Anforderungen an Dachdeckungs und Wandbekleidungselemente fest, die für die Herstellung von Außen und Innenwandbekleidungen sowie Eindeckungen von geneigten Dächern verwendet werden und aus Aluminiumblech mit oder ohne zusätzliche Oberflächenbehandlung (organische Beschichtungen oder Anodisierung) bestehen.
Dieses Dokument legt allgemeine Merkmale, Definitionen und Beschriftung für die Elemente fest, sowie die Anforderungen an die Werkstoffe, aus denen die Elemente hergestellt werden können. Es ist dafür bestimmt, von Herstellern verwendet zu werden, um sicherzustellen, dass ihre Produkte den Anforderungen entsprechen, oder vom Käufer, um zu überprüfen, ob die Produkte in Einklang mit den Anforderungen stehen, bevor sie das Werk verlassen. Diese Norm legt die Anforderungen fest, unter denen die Elemente allen normalen Einsatzbedingungen gerecht werden. Bei den Dachdeckungselementen kann es sich um vorgefertigte oder halbfertige Elemente sowie um Blechstreifen, Band und Bleche für die Verarbeitung auf der Baustelle (z. B. Stehfalzdächer) handeln.
Die Norm gilt für alle überlappenden, vollflächig unterstützten Dachdeckungs und Wandbekleidungselemente aus Aluminiumblech. Anforderungen an die Unterkonstruktion, die Konstruktion des Dachsystems, die Ausführung der Verbindungen und der Zubehörteile sind nicht Teil dieser Norm.
Dieses Dokument gilt nicht für selbsttragende Aluminiumbleche, die von EN 508 2 abgedeckt werden.
Produits de couverture et bardage en tôle métallique - Spécification pour les produits de couverture en tôle d'aluminium totalement supportés
Le présent document spécifie les prescriptions relatives aux produits de couverture et de bardage destinés à être assemblés pour constituer des couvertures, des bardages, des parements intérieurs, des toits en pente, fabriqués à partir de tôles d'aluminium, avec ou sans traitement de surface supplémentaire (revêtement organique ou anodisation).
Le présent document donne les caractéristiques générales, les définitions et l'étiquetage applicables aux produits, de même que les prescriptions relatives aux matériaux à partir desquels les produits peuvent être fabriqués. Il est destiné à être utilisé soit par les producteurs en vue de démontrer que leurs produits sont conformes aux prescriptions, soit par les acheteurs pour vérifier que les produits sont conformes avant leur expédition de l'usine. Il spécifie les prescriptions relatives aux produits pour leur permettre de répondre à toutes les conditions normales en service. Les produits peuvent être des produits préfabriqués ou des demi-produits partiellement formés ainsi que des bandes, des bobines ou des tôles pour des applications de façonnage sur chantier (couvertures à joints debout par exemple).
Le présent document s'applique à tous les produits de couverture et de bardage posés en discontinu et totalement supportés réalisés à partir de tôles en aluminium. Elle ne comporte aucune prescription relative au support de couverture, à la conception de la toiture et à l’exécution des assemblages et solins.
Le présent document ne traite pas des tôles d’aluminium autoportantes, qui sont couvertes par
l’EN 508-2.
Pločevina za pokrivanje streh in oblaganje sten - Specifikacija za povsem podprte proizvode iz aluminijske pločevine
Ta evropski standard določa zahteve za izdelke za pokrivanje streh in oblaganje sten, ki se uporabljajo v prevlekah za zunanje in notranje stenske obloge ter poševne strehe, izdelane iz aluminijeve pločevine z dodatno površinsko obdelavo ali brez nje (organska prevleka ali anodiziranje).
Ta standard določa splošne lastnosti, definicije in označevanje izdelkov ter zahteve za materiale, iz katerih so izdelki lahko proizvedeni. Namenjen je proizvajalcem, da se zagotovi skladnost njihovih izdelkov z zahtevami, oziroma kupcem, da lahko preverijo skladnost izdelkov pred razpošiljanjem iz tovarne. Določa zahteve za izdelke, ki omogočajo, da slednji izpolnjujejo vse običajne pogoje uporabe. Izdelki so lahko predizdelani ali poloblikovani izdelki ter tudi trakovi, zvitki in plošče za namestitev na mestu uporabe (npr. kritine s stoječim zgibom).
Standard se uporablja za vse nezvezno položene in povsem podprte izdelke za pokrivanje streh in oblaganje sten, izdelane iz aluminijeve pločevine. Standard ne vključuje zahtev za podporne konstrukcije, projektiranje strešnega sistema ter postavitev povezav in obrob.
Ta standard se ne uporablja za samonosilne aluminijeve pločevine, zajete v standardu EN 508-2.
General Information
Relations
Overview
EN 507:2019 - Roofing and cladding products from metal sheet - Specification for fully supported products of aluminium sheet (CEN) defines requirements for aluminium-based roofing and wall cladding products intended for fully supported installations. The standard covers prefabricated and semi‑formed elements as well as strip, coil and sheet for on‑site forming (e.g. standing seam roofs), with or without surface treatments such as organic coatings or anodising. EN 507:2019 is aimed at ensuring products meet normal service conditions and provides rules for product characteristics, material selection, labelling and factory quality control.
Key topics and requirements
- Scope and application
- Applies to discontinuously laid, fully supported roofing and cladding products made from aluminium sheet.
- Excludes self‑supporting aluminium products (covered by EN 508‑2) and does not cover supporting construction, system design or flashings.
- Materials
- Permitted aluminium alloys and tempers are referenced to material standards (EN 485, EN 1396); alloy/temper selection must meet corrosion resistance, strength and formability requirements.
- Suppliers are expected to provide inspection documents (EN 10204) where applicable.
- Surface treatments
- Accepts factory organic coatings (coil‑coated, post‑coated, laminated films) and anodised finishes; performance and test methods reference EN 1396 (coil coatings) and EN ISO 7599 (anodising).
- Reverse‑side coatings or special films may be used to reduce condensation dripping and aid handling/storage.
- Product requirements
- Mechanical properties, dimensions and tolerances are specified by cross‑references (EN 1396 for coated products; EN 485‑2 and EN 485‑4 for uncoated products).
- Includes provisions for sampling, type testing, marking, labelling, packaging, transport, storage and handling.
- Quality management
- Manufacturers must implement a permanent quality control system (aligned with EN ISO 9001 principles).
Applications and who uses EN 507:2019
- Manufacturers and fabricators of aluminium roofing and cladding products use EN 507:2019 to design, produce and certify fully supported sheets, coils and prefabricated elements.
- Purchasers, specifiers, architects, façade engineers, contractors and procurement teams use the standard to verify product compliance before dispatch and to specify materials in tenders.
- Test laboratories and certification bodies reference the standard for type testing and conformity assessment.
- Typical applications: pitched roofs with standing seams, internal linings, external wall cladding systems and decorative façades where aluminium sheet is fully supported.
Related standards
- EN 1396 - Coil coated aluminium (performance and test methods)
- EN 485‑1 / EN 485‑2 / EN 485‑4 - Aluminium sheet material conditions, mechanical properties and tolerances
- EN ISO 7599 - Anodizing of aluminium
- EN 508‑2 - Self‑supporting metal roofing products (aluminium)
Keywords: EN 507:2019, aluminium roofing, aluminium cladding, fully supported products, organic coating, anodised aluminium, CEN standard, roofing and cladding standards.
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2019
Nadomešča:
SIST EN 507:2000
Pločevina za pokrivanje streh in oblaganje sten - Specifikacija za povsem podprte
proizvode iz aluminijske pločevine
Roofing and cladding products from metal sheet - Specification for fully supported
products of aluminium sheet
Dachdeckungs- und Wandbekleidungselemente aus Metallblech - Festlegungen für
vollflächig unterstützte Bedachungselemente aus Aluminiumblech
Produits de couverture et bardage en tôle métallique - Spécification pour les produits de
couverture en tôle d'aluminium totalement supportés
Ta slovenski standard je istoveten z: EN 507:2019
ICS:
77.150.10 Aluminijski izdelki Aluminium products
91.060.20 Strehe Roofs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 507
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2019
EUROPÄISCHE NORM
ICS 77.150.10; 91.060.20 Supersedes EN 507:1999
English Version
Roofing and cladding products from metal sheet -
Specification for fully supported products of aluminium
sheet
Produits de couverture et bardage en tôle métallique - Dachdeckungs- und Wandbekleidungselemente aus
Spécification pour les produits de couverture en tôle Metallblech - Festlegungen für vollflächig unterstützte
d'aluminium totalement supportés Bedachungselemente aus Aluminiumblech
This European Standard was approved by CEN on 26 May 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 507:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, symbols and abbreviations . 6
3.1 Terms and definitions . 6
3.2 Symbols and abbreviations . 7
4 Requirements . 8
4.1 General . 8
4.2 Materials . 8
4.2.1 Aluminium . 8
4.2.2 Organic coatings . 9
4.2.3 Anodizing . 10
4.3 Products . 10
4.3.1 Flat products . 10
4.3.2 Formed (prefabricated) products . 10
4.3.3 Safety in case of fire . 10
5 Sampling and test methods . 10
5.1 Flat products . 10
5.2 Formed (prefabricated) products . 11
5.2.1 Sampling . 11
5.2.2 Testing . 11
6 Designation. 11
7 Marking, labelling, packaging, special ordering conditions, transport, storage and
handling . 11
7.1 Marking and labelling . 11
7.2 Packaging and any special ordering conditions . 12
7.3 Transport, storage and handling . 12
Bibliography . 13
European foreword
This document (EN 507:2019) has been prepared by Technical Committee CEN/TC 128 “Roof covering
products for discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest byFebruary 2020, and conflicting national standards shall
be withdrawn at the latest by February 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 507:1999.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
In comparison to the previous edition following technical changes were made:
— scope of the standard has been extended to cladding products;
— reference has been added to anodised aluminium sheets;
— list aluminium alloys suitable without further proof provided their properties conform to the values
given in the respective material standards (EN 485 or EN 1396) as well as concerning organic
coatings suitable for application to aluminium substrates within the scope of this standard have been
changed;
— Annex A concerning the national A-deviations was deleted.
These changes or additions can be found in the following Clauses and subclauses: 1; 2; 3.1.2; 3.1.3; 3.1.5;
3.1.6; 3.1.7; 3.2; 4.1; 4.2.1; 4.2.2; 4.2.3; 4.3.3; 5.1; 5.2.1; 5.2.2.2 and 7.3.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
Introduction
Figure 1 indicates the position of this standard in the CEN framework of standards concerning roofing
and cladding products of metal sheet.
Figure 1 — Framework of standards
In this standard the performance of the product has been defined in terms of a number of type tests.
The performance of a roof or cladding constructed with these products depends not only on the
properties of the product as it is required by this document, but also on the design, construction and
performance of the roof or the cladding as a whole in relation to the environment and conditions of use.
Metallic coated aluminium sheet can be easily fabricated. It can be sheared, punched, pressed, drawn,
folded, roll-formed without difficulty within the given limits of the properties listed in the respective
material specifications.
Coil coated sheet can be fabricated like metallic coated aluminium sheet in most applications, but
minimum bend radius, design of forming tools, process temperature, etc. are chosen according to material
properties.
1 Scope
This document specifies requirements for roofing and cladding products used for assembly into coverings
for wall claddings, linings and pitched roofs, made from aluminium sheet with or without additional
surface treatment (organic coating or anodising).
This document establishes general characteristics, definitions and labelling of the products, together with
requirements for the materials from which the products can be manufactured. It is intended to be used
either by manufacturers to ensure that their products comply with the requirements or by purchasers to
verify that the products comply before they are despatched from the factory. It specifies the requirements
for products which enable them to meet all normal service conditions. Products can be prefabricated or
semi-formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam
roofs).
This document applies to all discontinuously laid and fully supported roofing and cladding products made
of aluminium sheets. No requirements for supporting construction, design of roof system and execution
of connections and flashings are included.
This document does not appl
...
Frequently Asked Questions
EN 507:2019 is a standard published by the European Committee for Standardization (CEN). Its full title is "Roofing and cladding products from metal sheet - Specification for fully supported products of aluminium sheet". This standard covers: This document specifies requirements for roofing and cladding products used for assembly into coverings for wall claddings, linings and pitched roofs, made from aluminium sheet with or without additional surface treatment (organic coating or anodising). This document establishes general characteristics, definitions and labelling of the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. Products can be prefabricated or semi-formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam roofs). This document applies to all discontinuously laid and fully supported roofing and cladding products made of aluminium sheets. No requirements for supporting construction, design of roof system and execution of connections and flashings are included. This document does not apply to self-supporting aluminium sheets that are covered by EN 508-2.
This document specifies requirements for roofing and cladding products used for assembly into coverings for wall claddings, linings and pitched roofs, made from aluminium sheet with or without additional surface treatment (organic coating or anodising). This document establishes general characteristics, definitions and labelling of the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. Products can be prefabricated or semi-formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam roofs). This document applies to all discontinuously laid and fully supported roofing and cladding products made of aluminium sheets. No requirements for supporting construction, design of roof system and execution of connections and flashings are included. This document does not apply to self-supporting aluminium sheets that are covered by EN 508-2.
EN 507:2019 is classified under the following ICS (International Classification for Standards) categories: 77.150.10 - Aluminium products; 91.060.20 - Roofs. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 507:2019 has the following relationships with other standards: It is inter standard links to EN 507:1999, prEN 507. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 507:2019 is associated with the following European legislation: EU Directives/Regulations: 305/2011. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase EN 507:2019 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...