prEN 4500-004
(Main)Aerospace series - Metallic materials - Rules for drafting and presentation of material standards - Part 004: Specific rules for titanium and titanium alloys
Aerospace series - Metallic materials - Rules for drafting and presentation of material standards - Part 004: Specific rules for titanium and titanium alloys
The EN 4500 series specifies the rules for the drafting and presentation of metallic material standards for aerospace applications.
This Part 004 specifies the “Specific rules for titanium and titanium alloys”.
Luft- und Raumfahrt - Metallische Werkstoffe - Regeln für das Erstellen und die Gestaltung von Werkstoffnormen - Teil 004: Besondere Regeln für Titan und Titanlegierungen
Die Reihe EN 4500 legt die Regeln für das Erstellen und die Gestaltung von Normen für metallische Werkstoffe zur Anwendung in der Luft- und Raumfahrt fest.
Dieser Teil 004 legt die „Besonderen Regeln für Titan und Titanlegierungen“ fest.
Série aérospatiale - Matériaux métalliques - Règles pour la rédaction et la présentation des normes matériaux - Partie 004 : Règles spécifiques au titane et aux alliages de titane
No Scope available
Aeronavtika - Kovinski materiali - Pravila za načrtovanje in predstavljanje standardov za materiale - 004. del: Posebna pravila za titan in titanove zlitine
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2025
Aeronavtika - Kovinski materiali - Pravila za načrtovanje in predstavljanje
standardov za materiale - 004. del: Posebna pravila za titan in titanove zlitine
Aerospace series - Metallic materials - Rules for drafting and presentation of material
standards - Part 004: Specific rules for titanium and titanium alloys
Luft- und Raumfahrt - Metallische Werkstoffe - Regeln für das Erstellen und die
Gestaltung von Werkstoffnormen - Teil 004: Besondere Regeln für Titan und
Titanlegierungen
Série aérospatiale - Matériaux métalliques - Règles pour la rédaction et la présentation
des normes matériaux - Partie 004 : Règles spécifiques au titane et aux alliages de
titane
Ta slovenski standard je istoveten z: prEN 4500-004
ICS:
01.120 Standardizacija. Splošna Standardization. General
pravila rules
49.025.30 Titan Titanium
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2025
ICS 01.120 Will supersede EN 4500-004:2024
English Version
Aerospace series - Metallic materials - Rules for drafting
and presentation of material standards - Part 004: Specific
rules for titanium and titanium alloys
Série aérospatiale - Matériaux métalliques - Règles Luft- und Raumfahrt - Metallische Werkstoffe - Regeln
pour la rédaction et la présentation des normes für das Erstellen und die Gestaltung von
matériaux - Partie 004 : Règles spécifiques au titane et Werkstoffnormen - Teil 004: Besondere Regeln für
aux alliages de titane Titan und Titanlegierungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 4500-004:2025 E
worldwide for CEN national Members.
Contents Page
Foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Rules for drafting a European standard for aerospace metallic materials. 6
4.1 General. 6
4.2 Title . 6
4.2.1 General. 6
4.2.2 Method of melting . 6
4.2.3 Form entries . 7
4.2.4 Additional information entries . 8
4.3 Introduction . 8
4.4 Scope, normative references, terms and definitions, requirements . 8
4.5 Table 1 . 9
4.5.1 Line 1: Material designation . 9
4.5.2 Line 2: Chemical composition. 9
4.5.3 Line 3: Method of melting . 9
4.5.4 Line 4.1: Form . 9
4.5.5 Line 4.2: Method of production . 9
4.5.6 Line 4.3: Further intended processing . 9
4.5.7 Line 4.4: Limit dimension(s) . 9
4.5.8 Line 5.1: Technical specification . 9
4.5.9 Line 5.2: Dimensional standard . 10
4.5.10 Line 6.1: Delivery condition and Heat treatment . 10
4.5.11 Line 6.2: Delivery condition code . 10
4.5.12 Line 7: Use condition and Heat treatment . 10
4.5.13 Line 8.1: Test sample(s) . 10
4.5.14 Line 8.2: Test piece(s) . 10
4.5.15 Line 8.3: Heat treatment . 11
4.5.16 Line 9: Dimensions concerned . 11
4.5.17 Line 10: Thickness of cladding on each face . 11
4.5.18 Line 11: Direction of test piece . 11
4.5.19 Lines 12 to 16: Tensile (T) . 11
4.5.20 Line 17: Hardness . 11
4.5.21 Line 18: Shear strength . 11
4.5.22 Line 19: Bending . 11
4.5.23 Line 20: Impact strength . 11
4.5.24 Lines 21 to 26: Creep (C) . 11
4.5.25 Line 27 . 11
4.5.26 Line 29: Reference heat treatment . 12
4.5.27 Lines 30 to 94 . 12
4.5.28 Line 95: Marking inspection . 12
4.5.29 Line 96: Dimensional inspection . 12
4.5.30 Line 97 . 12
4.5.31 Line 98: Notes . 12
4.5.32 Line 99: Typical use . 12
4.5.33 Line 100: Product qualification . 12
4.6 Bibliography . 12
Annex A (informative) Completion of title page . 13
Annex B (informative) Completion of the introduction . 14
Annex C (informative) Completion of the scope, normative references, terms and
definitions, and requirements . 15
Annex D (informative) Completion of Table 1 . 16
Annex E (informative) Completion of the bibliography. 22
Bibliography . 23
Foreword
This document (prEN 4500-004:2025) has been by the Technical Committee ASD-STAN/D04
“Material”.
This document is currently submitted to the CEN Enquiry
This document will supersede EN 4500-004:2024.
EN 4500-004:2024:
— addition of the lines 4.3 "Further intended processing" and 5.2 "Dimensional standard" in the body
of the document and in Annex D;
— addition of introductory sentences to Table 1 in Annex C to highlight the fact that the table is a
normative element and that all the documents that it lists shall be applied;
— overall editorial modifications to give clarity on the normative or informative nature of the
references made to other documents or Annexes;
— restructuring of the document and simplification of the Template to achieve a single continuous
table.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
Introduction
This document is part of the series of EN metallic material standards for aerospace applications. The
general organization of this series is described in EN 4258.
The EN 4500 series (Aerospace series — Metallic materials — Rules for drafting and presentation of
material standards) is composed by the following documents:
— General rules EN 4500-001;
— Specific rules for aluminium, aluminium alloys and EN 4500-002;
magnesium alloys
— Specific rules for heat-resisting alloys EN 4500-003;
— Specific rules for titanium and titanium alloys EN 4500-004;
— Specific rules for steels EN 4500-005;
— Specific rules for filler metals for welding EN 4500-002 to EN 4500-005;
— Specific rules for filler metals for brazing EN 4500-006.
Basis for the drafting of all European standards is CEN/CENELEC Internal Regulations — Part 3:
Principles and rules for the structure and drafting of CEN
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.