prEN 16585-3
(Main)Railway applications - Design for PRM use - Equipment and components on board rolling stock - Part 3: Clearways and internal doors
Railway applications - Design for PRM use - Equipment and components on board rolling stock - Part 3: Clearways and internal doors
This document describes the specific ‘Design for PRM use’ requirements applying to rolling stock and the assessment of those requirements. The following applies to this document:
— The definitions and requirements describe specific aspects of ‘Design for PRM use’ required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI
— This document defines elements which are universally valid for obstacle-free travelling including toilets, elements for sitting, standing and moving and clearways and internal doors. The definitions and requirements of this standard are to be used for rolling stock applications
— This document only refers to aspects of accessibility for PRM passengers; it does not define non-PRM related requirements and definitions.
— This document assumes that the rolling stock is in its defined operating condition.
— Where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements.
The 'Equipment and components' standard is written in three parts:
— Part 1 contains:
— Toilets
— Part 2 contains:
— Handholds
— Seats
— Wheelchair spaces
— This document is Part 3 and contains:
— Clearways
— Internal doors.
Bahnanwendungen - Gestaltung für die Nutzung durch PRM - Ausstattung und Bauteile in Schienenfahrzeugen - Teil 3: Lichte Räume und Innentüren
Applications ferroviaires - Conception destinée à l'usage par les PMR - Equipements et éléments à bord du matériel roulant - Partie 3 : Passages et portes intérieures
Železniške naprave - Načrtovanje za osebe z omejenimi gibalnimi sposobnostmi - Oprema in sestavni deli na železniških vozilih - 3. del: Prehodi in notranja vrata
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 16585-3:2022
01-julij-2022
Železniške naprave - Načrtovanje za osebe z omejenimi gibalnimi sposobnostmi -
Oprema in sestavni deli na železniških vozilih - 3. del: Prehodi in notranja vrata
Railway applications - Design for PRM use - Equipment and components on board
rolling stock - Part 3: Clearways and internal doors
Bahnanwendungen - Gestaltung für die Nutzung durch PRM - Ausstattung und Bauteile
in Schienenfahrzeugen - Teil 3: Lichte Räume und Innentüren
Applications ferroviaires - Conception destinée à l'usage par les PMR - Equipements et
éléments à bord du matériel roulant - Partie 3 : Passages et portes intérieures
Ta slovenski standard je istoveten z: prEN 16585-3
ICS:
11.180.01 Pripomočki za Aids for disabled and
onesposobljene in handicapped persons in
hendikepirane osebe na general
splošno
45.060.20 Železniški vagoni Trailing stock
oSIST prEN 16585-3:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 16585-3:2022
---------------------- Page: 2 ----------------------
oSIST prEN 16585-3:2022
DRAFT
EUROPEAN STANDARD
prEN 16585-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2022
ICS 11.180.01; 45.060.20 Will supersede EN 16585-3:2017
English Version
Railway applications - Design for PRM use - Equipment
and components on board rolling stock - Part 3: Clearways
and internal doors
Applications ferroviaires - Conception destinée à Bahnanwendungen - Gestaltung für die Nutzung durch
l'usage par les PMR - Equipements et éléments à bord PRM - Ausstattung und Bauteile in Schienenfahrzeugen
du matériel roulant - Partie 3 : Passages et portes - Teil 3: Lichte Räume und Innentüren
intérieures
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 256.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16585-3:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 16585-3:2022
prEN 16585-3:2022 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Symbols and abbreviations . 8
5 Requirements and assessment . 8
5.1 General. 8
5.2 Doors .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.