Railway applications - Track - Performance requirements for fastening systems - Part 3: Fastening systems for wood and polymeric composite sleepers

This document is applicable to fastening systems, in Categories A - E as specified in EN 13481-1:2012, 3.1 for use on wood or polymeric composite sleepers in ballasted or ballastless track, including track on open deck bridges, with respective maximum axle loads and minimum curve radii as shown in Table 1.
[Table 1 - Fastening category criteria]
NOTE   The maximum axle load for Categories A and B does not apply to maintenance vehicles.
The requirements apply to:
-   fastening systems that act on the foot and/or web of the rail including direct fastening systems and indirect fastening systems;
-   fastening systems for rail sections included in EN 13674-1:2011+A1:2017 (excluding 49E4) or EN 13674-4:2019.
This document is not applicable to fastening systems for other rail sections, rigid fastening systems, special fastening systems used at bolted joints or glued joints or special low clamping force fastenings used to mitigate track-bridge interaction effects.
This document is for type approval of complete fastening systems.

Bahnanwendungen - Oberbau - Leistungsanforderungen für Schienenbefestigungssysteme - Teil 3: Befestigungssysteme für Holz- und Polymerverbundschwellen

Dieses Dokument ist anzuwenden für Befestigungssysteme in den Kategorien A bis E, wie in EN 13481 1:2012, 3.1, festgelegt, für die Verwendung auf Holz- oder Polymerverbundschwellen in Schottergleisen oder in Festen Fahrbahnen, einschließlich Gleisen in Brücken mit offener Fahrbahn, jeweils mit maximalen Auslegungsachslasten und Mindestbogenradien, wie in Tabelle 1 dargestellt.
Die Anforderungen gelten für:
—   Befestigungssysteme, die am Schienenfuß und/oder Schienensteg wirken, einschließlich direkter und indirekter Befestigungssysteme;
—   Befestigungssysteme für Schienenprofile nach EN 13674 1:2011+A1:2017 (außer 49E4) oder EN 13674 4:2019.
Dieses Dokument ist nicht anzuwenden für Befestigungssysteme für andere Schienenprofile, starre Befestigungssysteme, spezielle Befestigungssysteme, die für verschraubte oder geklebte Schienenstöße verwendet werden oder Spezialbefestigungen mit niedriger Spannkraft, die zur Abschwächung von wechselseitigen Einflüssen zwischen Gleis und Brücke verwendet werden.
Dieses Dokument gilt für die Typzulassung kompletter Befestigungssysteme.

Applications ferroviaires - Voie - Exigences de performance pour les systèmes de fixation - Partie 3 : Systèmes de fixation pour traverses en bois et en composite à matrice polymère

Le présent document est applicable aux systèmes de fixation des catégories A à E spécifiées dans l'EN 13481-1:2012, 3.1 pour utilisation sur des traverses en bois ou en composite à matrice polymère en voie ballastée ou sans ballast, y compris sur des ponts à tablier à l'air libre, avec des charges à l'essieu maximales respectives et des rayons de courbure minimaux selon le Tableau 1.
[Tableau 1 - Critères de classification des systèmes de fixation]
NOTE   La charge à l'essieu maximale pour les catégories A et B ne s'applique pas aux véhicules de maintenance.
Les exigences s'appliquent :
-   aux systèmes de fixation qui agissent sur le patin et/ou l'âme du rail, y compris les systèmes de fixation directs et les systèmes de fixation indirects ;
-   aux systèmes de fixation pour les profils de rail décrits dans l'EN 13674-1:2011+A1:2017 (à l'exclusion du profil 49E4) ou l'EN 13674-4:2019.
Le présent document ne s'applique pas aux systèmes de fixation destinés à d'autres profils de rail, aux systèmes de fixation rigides, aux systèmes de fixation spéciaux utilisés au droit des éclisses ou aux fixations par effort d'application au patin du rail utilisées pour limiter les effets liés à l'interaction voie-ouvrage d’art.
Le présent document est destiné à l'homologation de type de systèmes de fixation complets.

Železniške naprave - Zgornji ustroj proge - Zahteve za izdelavo pritrdilnih sistemov - 3. del: Pritrdilni sistemi za lesene in polimerne kompozitne prage

Ta evropski standard se uporablja za pritrdilne sisteme v kategorijah od A do C
iz točke 3.1 standarda EN 13481-1:2012 za lesene ali polimerne prage pri zgornjem ustroju s tamponskim slojem z največjo osno obremenitvijo in najmanjšim krivinskim polmerom, kot je prikazano v preglednici 1.
Preglednica 1 – Merila za kategorije pritrjevanja
Kategorija       Največja osna obremenitev        Najmanjši krivinski polmer
                                kN                                   m
A                          130                                   40
B                          180                                   80
C                          260                                  150
D                          260                                   400
E                          350                                   150
OPOMBA: Največja osna obremenitev za kategoriji A in B ne velja za vzdrževalna vozila.
Zahteve se uporabljajo za:
– pritrdilne sisteme, ki delujejo na vznožje in/ali stojino tirnice, vključno z neposrednimi
in posrednimi pritrdilnimi sistemi;
– pritrdilne sisteme za dele železnice iz standarda EN 13674-1 (razen 49E4) ali EN 13674-4.
Ne uporablja se za pritrdilne sisteme za druge dele železnice, toge pritrdilne sisteme
ali posebne pritrdilne sisteme, ki se uporabljajo pri zakovičenih spojih ali zlepljenih spojih.
Ta standard naj se uporablja le za odobritev tipa celotnih pritrdilnih sistemov.

General Information

Status
Published
Publication Date
12-Jul-2022
Withdrawal Date
30-Jan-2023
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
13-Jul-2022
Due Date
30-Sep-2022
Completion Date
13-Jul-2022

Relations

Buy Standard

Standard
EN 13481-3:2022
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2022
Nadomešča:
SIST EN 13481-3:2012
Železniške naprave - Zgornji ustroj proge - Zahteve za izdelavo pritrdilnih sistemov
- 3. del: Pritrdilni sistemi za lesene in polimerne kompozitne prage
Railway Applications - Track - Performance Requirements for Fastening Systems - Part
3: Fastening Systems for wood and polymeric composite sleepers
Bahnanwendungen - Oberbau - Leistungsanforderungen für
Schienenbefestigungssysteme - Teil 3: Befestigungssysteme für Holz- und
Polymerverbundschwellen
Applications ferroviaires - Voie - Exigences de performance pour les systèmes de
fixation - Partie 3 : Systèmes de fixation pour traverses en bois et en composite à
matrice polymère
Ta slovenski standard je istoveten z: EN 13481-3:2022
ICS:
93.100 Gradnja železnic Construction of railways
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13481-3
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2022
EUROPÄISCHE NORM
ICS 93.100 Supersedes EN 13481-3:2012
English Version
Railway applications - Track - Performance requirements
for fastening systems - Part 3: Fastening systems for wood
and polymeric composite sleepers
Applications ferroviaires - Voie - Exigences de Bahnanwendungen - Oberbau -
performance pour les systèmes de fixation - Partie 3 : Leistungsanforderungen für
Systèmes de fixation pour traverses en bois et en Schienenbefestigungssysteme - Teil 3:
composite à matrice polymère Befestigungssysteme für Holz- und
Polymerverbundschwellen
This European Standard was approved by CEN on 8 May 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13481-3:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 3
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Symbols . 9
5 Requirements determined by laboratory testing . 9
5.1 Specimens used for laboratory testing . 9
5.2 Longitudinal rail restraint . 10
5.2.1 General case . 10
5.2.2 Special case for long structures . 10
5.3 Torsional resistance . 10
5.4 Clamping force and uplift stiffness . 10
5.5 Vertical stiffness . 10
5.6 Effect of repeated loading . 11
5.7 Effect of exposure to severe environmental conditions . 12
5.8 Electrical resistance of fastening system and sleeper . 12
5.9 Pull-out resistance of embedded fastening components (polymeric composite
sleepers only) . 12
6 Other requirements . 12
6.1 Dimensions . 12
6.2 Effect of the fastening system tolerances on track gauge . 13
6.3 In-service testing . 14
6.4 Attenuation of noise and vibration . 14
7 Fitness for purpose . 15
8 Marking, labelling and packaging . 15
Annex A (informative) Vibration and noise . 16
A.1 General . 16
A.2 Symbols . 16
A.3 Parameters for environmental vibration calculations . 16
A.4 Calculating the vibration attenuation . 17
A.5 Environmental noise . 17
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive (EU) 2016/797 aimed to be covered . 18
Bibliography . 20

European foreword
This document (EN 13481-3:2022) has been prepared by Technical Committee CEN/TC 256 “Railway
applications”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2023, and conflicting national standards shall
be withdrawn at the latest by January 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13481-3:2012.
The main changes compared to the previous edition are as follows:
a) introduction of the application for fastenings on polymeric composite sleepers;
b) inclusion of tests for fastenings with very low stiffness;
c) changes to the loading conditions for Category B fastenings;
d) inclusion of details of in-service testing, replacing the reference to EN 13146-8, which is to be
withdrawn;
e) editorial changes to make clear which requirements are based on laboratory testing.
This European Standard is one of the series EN 13481 “Railway applications — Track — Performance
requirements for fastening systems”, which consists of the following parts:
— Part 1: Definitions
— Part 2: Fastening systems for concrete sleepers in ballast
— Part 3: Fastening systems for wood and polymeric composite sleepers
— Part 4: Fastening systems for steel sleepers
— Part 5: Fastening systems for ballastless tracks
— Part 7: Fastening systems for switches and crossings, check rails, insulated rail joints and rail expansion
devices
NOTE Part 6 does not exist in this series.
These European Standards are supported by the test methods in the series EN 13146 “Railway
applications — Track — Test methods for fastening systems”.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral part
of this document.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
Introduction
A series of tests is used to assess the suitability of fastening systems for use in railway track, i.e. for type
approval of complete fastening systems. This document only sets requirements considered relevant to
ensure the safe, long-term operation of the track systems. The test methods are described in other
associated standards.
The various categories of rail fastenings used in this document are defined in EN 13481-1:2012.
1 Scope
This document is applicable to fastening systems, in Categories A – E as specified in EN 13481-1:2012,
3.1 for use on wood or polymeric composite sleepers in ballasted or ballastless track, including track on
open deck bridges, with respective maximum axle loads and minimum curve radii as shown in Table 1.
Table 1 — Fastening category criteria
Category Maximum design axle load Minimum curve radius
kN m
A 130 40
B 180 80
C 260 150
D 260 400
E 350 150
NOTE The maximum axle load for Categories A and B does not apply to maintenance vehicles.
The requirements apply to:
— fastening systems that act on the foot and/or web of the rail including direct fastening systems and
indirect fastening systems;
— fastening systems for rail sections included in EN 13674-1:2011+A1:2017 (excluding 49E4) or
EN 13674-4:2019.
This document is not applicable to fastening systems for other rail sections, rigid fastening systems,
special fastening systems used at bolted joints or glued joints or special low clamping force fastenings
used to mitigate track-bridge interaction effects.
This document is for type approval of complete fastening systems.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 13145:2001+A1:2011, Railway applications — Track — Wood sleepers and bearers
EN 13146-1:2019, Railway applications — Track — Test methods for fastening systems — Part 1:
Determination of longitudinal rail restraint
EN 13146-2:2012, Railway applications — Track — Test methods for fastening systems — Part 2:
Determination of torsional resistance
EN 13146-4:2020, Railway applications — Track — Test methods for fastening systems — Part 4: Effect of
repeated loading
EN 13146-5:2012 , Railway applications — Track — Test methods for fastening systems — Part 5:
Determination of electrical resistance
EN 13146-6:2012, Railway applications — Track — Test methods for fastening systems — Part 6: Effect of
severe environmental conditions
EN 13146-7:2019, Railway applications — Track — Test methods for fastening systems — Part 7:
Determination of clamping force and uplift stiffness
EN 13146-9:2020, Railway applications — Track — T
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.